Kyocera Mita FS-C8008DN - Color Laser Printer Quick Reference Manual
  1. Manuals
  2. Brands
  3. Kyocera Mita Manuals
  4. Printer
  5. Ecosys FS-C8008DN Series
  6. Quick reference manual

Kyocera Mita FS-C8008DN - Color Laser Printer Quick Reference Manual

Color laser printer
Hide thumbs Also See for FS-C8008DN - Color Laser Printer:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
FS-C8008N
FS-C8008DN
Color Laser Printer
Quick Reference Guide

Advertisement

Table of Contents
loading

Related Manuals for Kyocera Mita FS-C8008DN - Color Laser Printer

Summary of Contents for Kyocera Mita FS-C8008DN - Color Laser Printer

  • Page 1 FS-C8008N FS-C8008DN Color Laser Printer Quick Reference Guide...
  • Page 2 All rights are reserved. Copying or other repro- duction of all or part of this manual, any copyrightable subject matter without the prior written consent of Kyocera Mita Corpora- tion is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which the copying is done.
  • Page 3 FS-C8008N FS-C8008DN Quick Reference Guide...

  • Page 4: Table Of Contents

    Contents Guide to the information about the printer .........3 Understanding the Error Messages ...........4 Loading Paper .................14 Clearing Paper Jams ...............18 [Paper Jam — Right Cover #] ........19 [Paper Jam — Cassette #] ..........19 [Paper Jam — MP Tray] ..........20 [Paper Jam —...

  • Page 5: Guide To The Information About The Printer

    Software and Docu- These CDs include the printer software for ment CD-ROMs Kyocera Mita printers such as printer drivers, network printer monitors, and various soft- ware utilities. Also, these CDs include the Operation Guides and other documents.

  • Page 6: Understanding The Error Messages

    Understanding the Error Messages These messages appear on the printer’s message dis- play when the printer needs the operator’s attention. For more details, refer to chapter 4 of the Operation Guide. Message Corrective Action Add paper MPTray The paper has run out in the paper source displayed.
  • Page 7 Message Corrective Action The corresponding paper cassette is not Cassette # installed. Install the cassette. The cassette not loaded number can be 1 (topmost) to 6 (bottom); and for the DN model, 2 to 6. This message warns following two cases. Check waste Install the new waste toner box.
  • Page 8 Message Corrective Action The duplex drawer is not installed. Install Duplex drawer the duplex drawer. This message is appli- not loaded cable to the DN model. The face-down tray has become full Face-down tray (approx. 500 pages). You must remove all paper full printed pages from the face-down tray.
  • Page 9 Message Corrective Action The hard disk installed in the printer is not Format error formatted, and therefore cannot be read or Hard disk written. To format the hard disk, follow the procedure in the Installation Guide of the hard disk. A hard disk error has occurred.
  • Page 10 † Replacement of the maintenance kit is necessary at every 600,000 images of printing and requires professional servic- ing. Contact your Kyocera Mita dealer. Replace Maintenance Kit B. Replacement Install MK of the maintenance kit B is necessary at †...
  • Page 11 Message Corrective Action The paper cassette matching the paper Load Cassette # size and paper type of the print job is †† (A4)/(PLAIN) empty. Load paper into the paper cassette indicated by #. Press the GO key to resume printing. If you want to print from a different paper source, press the key to display...
  • Page 12 Message Corrective Action There is no paper cassette installed in the Load MP Tray printer that matches the paper size and †† (A4)/(PLAIN) paper type of the print job. Set paper in the MP tray. Press the GO key to resume printing.
  • Page 13 Message Corrective Action The total amount of data received by the Memory overflow printer exceeds the printer’s internal mem- Press GO ory. Try adding more memory. Press the GO key to resume printing. You can aban- don printing by the CANCEL key. If Auto Continue is set to On, printing will be automatically resumed after a preset period of time.
  • Page 14 Message Corrective Action The print job transferred to the printer was Print overrun too complex to print on a page. Press the ††† Press GO GO key to resume printing. (The page may break in some pages.). You can abandon printing by the CANCEL key.
  • Page 15 Message Corrective Action A tray of the optional sorter (SO-30) is full. Sorter tray Remove paper sheets in the correspond- paper full ing tray as displayed in place of ##. The optional sorter (SO-30) tray is full. Sorter Remove printed pages. paper full The optional sorter (SO-30) is not installed Sorter...

  • Page 16: Loading Paper

    Loading Paper Fan the media (paper/transparencies), then tap it on a level surface to avoid media jams or skewed Caution printing. Loading paper into the cassette Pull out the paper feed cassette until it stops. Lift the paper feed roller located on the right side of the cassette upright.
  • Page 17 Adjust the posi- Paper Stopper tion of the paper guides according to the size of the paper you will use. To move the paper guides, press the green- colored knobs. Paper Guide Align the paper stopper correctly with the markings in the cassette that match the paper size:...
  • Page 18 Square the edges Paper Limit Indicator of the paper and Paper Size Indicators Position insert into the paper feed cas- sette. Be sure that the paper does not exceed the paper limit indica- tors. The paper Paper Guide feed cassette can hold up to about 500 sheets.
  • Page 19 Loading paper into the MP (Multi-Purpose) tray Open the MP tray located on the right side of the printer. Paper Guide Paper Guide Adjust the position of the paper guides according to the size of the paper you will use. Square the edges of the paper and insert into the MP tray.

  • Page 20: Clearing Paper Jams

    Clearing Paper Jams The figure below is a simplified diagram showing the paper paths in the print system. You can clear paper jams easily and quickly if you become familiar with the paper paths and locations of potential jams. Depending on the indication on the message display, proceed as follows: When removing jammed paper, use extreme care to leave no paper debris in the printer.

  • Page 21: [Paper Jam - Right Cover #]

    [Paper Jam — Right Cover #] Open the paper feeder right cover according to the number in place of #, top (1) to bottom (3). Pull the paper out- ward. Close the right cover. [Paper Jam — Cassette #] Open the paper cassette accord- ing to the number in place of #, top...

  • Page 22: [Paper Jam - Mp Tray]

    [Paper Jam — MP Tray] Remove the jammed paper on the MP tray up and towards the right. [Paper Jam — Duplexer] Open the duplexer drawer. Lower Cover Open the upper and lower plastic covers and remove paper under the covers and rollers.

  • Page 23: [Paper Jam - Paper Transfer Unit]

    [Paper Jam — Paper Transfer Unit] Open the front cover. Pull the paper transfer unit out com- pletely. Paper Transfer Unit Remove the paper by swinging the green-col- ored lever to the right.
  • Page 24 Remove the paper on the rub- ber belts (black). Open the fuser access cover by pressing the green-colored lock lever.
  • Page 25 Open the fuser top cover. Raise the sub- cover by grasp- ing the clip marked as A on the rear side while removing the paper.
  • Page 26 If the paper is pinched between the rollers, turn the wheel. Rotate the wheel only in the direction illustrated in the diagram. Caution Turn the green- colored lever down to the six o’clock position. This allows you to draw out the pri- mary transfer roller.
  • Page 27 Turn the wheel (with gear teeth) on the right-hand side of the pri- mary transfer unit. Remove the jammed paper. Primary Transfer Unit Use care not to touch the drum component in the primary transfer unit. Caution Push the primary transfer unit back in.

  • Page 28: [Paper Jam - Left Cover]

    [Paper Jam — Left Cover] Open the face-up tray. Open the left cover by pulling the handle. Remove the jammed paper. If the paper is stuck under the roller, grasp the green-colored knob and rotate the roller in the direction indicated in the diagram so that the paper is driven out.

  • Page 29: [Paper Jam - Option Stacker/Finisher/Sorter]

    [Paper Jam — Option Stacker/Finisher/Sorter] Paper jam has occurred in the bulk stacker, document finisher, or sorter which is an optional equipment. Remove paper jam in the option unit.

  • Page 30: Toner Container Replacement

    Toner Container Replacement The life of the toner containers depends on the amount of toner required to accomplish your printing jobs. When 5 % coverage (a typical business document) of individual toner colors is assumed for A4 or letter size, †...

  • Page 31: Replacing The Toner Container

    Replacing the Toner Container You do not have to turn printer power off before starting the replacement. Any data that may be Note under printing process will be deleted if you turn printer power off. To replace the toner container, first make sure of the color of the toner container requiring replacement according to the message display.
  • Page 32 While pressing down the blue- colored lever at the end of the toner container, pull the toner con- tainer out. Put the old toner container in the plastic waste bag (contained in the toner kit) and dis- card it. Take the new toner container out of the toner kit.

  • Page 33: Replacing The Waste Toner Box

    Insert the new toner container all the way in. The container is locked automati- cally when it is properly seated. When the toner container has been replaced, proceed to the next section. Replacing the Waste Toner Box Replace the waste toner box each time you replace the toner container.
  • Page 34 The old waste toner box has a cap. Remove the cap (black) on the top of the box and put the cap onto the opening. This is to prevent the toner from spill- ing. Put the old waste toner box in the plastic waste bag (contained in the toner kit) and dis-...

  • Page 35: Cleaning The Printer

    Cleaning the Printer The following parts must be cleaned each time the toner container is replaced: • Registration roller • Belts • Main charger wire • Main charger grid These parts are explained in the following sections. In addition to this, it is recommended that these parts are cleaned periodically at least once a month.
  • Page 36 Clean the metal roller as shown (the registration roller) using the cleaning cloth (included in the toner kit). Registration Roller (Metal) Transfer Belt (brown) Clean the rubber belts (black) using Rubber Belts the cleaning cloth. Transfer Belt (brown)

  • Page 37: Cleaning The Main Charger Unit

    Cleaning the Main Charger Unit The main charger unit needs to be cleaned periodically as it gets contaminated with dioxide after a long usage, causing black streaks, etc. on the paper. The main charger is comprised of two main parts — the wire and the grid —...
  • Page 38 Cleaning the main charger grid — Take the grid cleaner (included in the toner kit) out of the protective bag Grid Cleaner and remove the cap. Attach the grid cleaner to the printer, with the pad facing up. Slightly lift the main charger unit.
  • Page 40 Kyocera Mita Corporation 2-28, 1-Chome, Tamatsukuri, Chuo-ku Osaka 540-8585, Japan Phone: (06) 6764-3555 2002.12 © 2002 by KYOCERA MITA CORPORATION 2CK80020A All rights reserved. Printed in Japan...

This manual is also suitable for:

Fs-c8008nFs-c8008n fs-c8008dn

Table of Contents