Disassembly Procedures; Moving And Replacing Range; Maintop Removal-Slide-In; Control Panel Diassembly-Slide-In - Amana ARGS7650 Service Manual

Disassembly Procedures

!

Moving and Replacing Range

1. Turn off electrical power and gas to the range.
2. Pull the oven forward out of the cabinet opening.
3. Unplug the power cord leading from unit and
disconnect the gas line.
4. Replace the range using the installation instructions
and anti-tip bracket(s).
Maintop Removal–Slide-In
1. Turn off electrical power and gas to the range.
2. Disconnect gas and power from unit.
3. Remove screws securing top surface burners.
4. Remove surface burner and disconnect spark ignitor
wire from surface burner.
5. Raise and remove maintop from unit.
Control Panel Disassembly–Slide-In
1. Turn off electrical power and gas to the range.
2. See "Maintop Removal–Slide-In" for removal.
3. Carefully pull surface burner knobs outward to
remove.
4. Remove screws located on front of control panel.
5. Remove screws securing end caps to unit.
6. Remove screws securing control panel to unit.
7. Pull control panel forward and tilt downward.
8. Remove screws securing ERC to control panel.
9. Depress side locking arms, push forward on oven
light switch, and disconnect wire terminals from
switch.
10.Replace and reassemble in reverse order.
ERC–Slide-In
!
While unplugging electrical connections pins may be
damaged, use extreme care when disconnecting.
1. Remove control panel, see "Control Panel Removal–
Slide-In" procedure, (steps 1-6).
2. Remove screws securing ERC to control panel.
3. Disconnect wires from ERC.
4. Replace and reassemble in reverse order.
Oven Light Switch–Slide-In
1. Remove control panel, see "Control Panel Removal–
Slide-In" procedure, (steps 1-6).
2. Depress side locking arms and push forward on
switch to release from control panel.
3. Disconnect wire terminals from switch.
4. Replace and reassemble in reverse order.
WARNING
WARNING
To avoid risk of electrical shock, personal injury, or
death: disconnect electrical and gas supply before
servicing.
Top Surface Valve and Spark Switch–
Slide-In
1. Remove control panel, see "Control Panel Removal–
Slide-In" procedure, (steps 1-6).
2. Remove spark switch by pulling straight off valve.
3. Remove wires by depressing release arm or pulling
terminal off.
3. Remove screw securing valve to front manifold.
4. Replace and reassemble in reverse order.
Spark Module–Slide-In
1. See "Maintop Removal–Slide-In" for removal.
2. Remove screws securing spark module bracket.
3. Disconnect wire terminals from spark module.
4. Replace and reassemble in reverse order.
ERC Cooling Fan–Slide-In
1. See "Maintop Removal–Slide-In" for removal.
2. Disconnect wire terminals from fan motor.
3. Remove screws securing cooling fan bracket.
4. Replace and reassemble in reverse order.
Oven High Limit/Thermal Fan Switch–
Slide-In
1. See "Maintop Removal–Slide-In" for removal.
2. Disconnect wire terminals from limiter.
3. Remove screws securing limiter.
4. Replace and reassemble in reverse order.
Maintop Removal–Freestanding
1. Turn off electrical power and gas to the range.
2. Disconnect gas and power from unit.
3. Remove screws securing surface burners to
maintop.
4. Raise and remove maintop assembly.
5. Replace and reassemble in reverse order.
Front Control Panel–Freestanding
1. Turn off electrical power and gas to the range.
2. Disconnect gas and power from unit.
3. Remove surface knobs.
4. Remove screws securing control panel to unit.
5. Pull forward on the bottom of control panel, then
slide forward.
6. Replace and reassemble in reverse order.
41 RS2310002 Rev. 1