Yanmar 6LY3 series Service Manual page 319

Troubleshooting by DTC Fault Codes
12/05
TFX Diagnostic Screen Display Procedure 1
Figure 13-6
When powered-up, the i5601E Digital Displays will initially display an introductory screen showing the software
revision level. They will then display one of the following four screens:
These screens show all of the key engine data and can be accessed by pushing a single button. The right-most
button allows the contrast and brightness to be set.
TFX Diagnostic Screen Display Procedure 2
Figure 13-7
The i5601E was set up at the factory with the keys assigned and locked as shown on page 6 of this manual. This
mode is the default mode and allows start up and operation of the engine. It serves many applications quite well.
The i5601E Digital Display unit has many additional features and capabilities. This section of the book shows
the use of some of these features.
Changing the basic set up is typically accomplished in one of two ways.
1. Go to the systems menu and alter basic selections.
2. Enable the right arrow key on the basic screens to allow changing of the data shown in the default
displays.
To enter the Main Menu press and hold key 5 until the menu appears.
To move around the menus use the softkeys at the bottom of the screen.
The function of a particular softkey changes from screen to screen to
whatever is most appropriate for the given screen.
NOTE : Any changes to the setup menus may require reconfiguring the i5601E HOT KEY SETUP.
BACK
EXIT
MORE
ON
OFF
6LY3 Service Manual
i5601E Digital Display Setup
Keys 1 2
Returns you to the previous menu or screen.
Decreases the setting of a selected menu item.
Moves the cursor arrow down to select the
next menu item in a list.
Exits the current menu and returns you to the
prior screen.
Increases the setting of a selected menu item.
Reveals additional keys and swaps them with
those currently shown.
Toggles the operational status of a currently
selected menu item.
Moves the cursor arrow up to select the
previous menu item in a list.
© 2007 Yanmar Marine International
In the unlikely event that an engine fault occurs, a warning box appears in the
display showing the cause of the fault, and the action to take. "Press Any Key
To Continue."
Pressing any key acknowledges the alarm and immediately switches the display to the Alarms screen. The
i5601E continues to beep until all alarm conditions (engine faults) have cleared. Unacknowledged alarms are
shown as flashing boxes. Press any key to acknowledge alarm boxes that may still be flashing, and they will then
change to a stready highlighted state.
Alarm blocks remain highlighted as long as the alarm condition (engine fault) remains and will automatically
reset to an un-highlighted state after the alarm condition has passed.
Note: The i5601E is an extremely versitle display. The four-left keys can be reconfigured to allow the user to
display whatever screens he or she desires. For additional operational details, refer to Appenbdix A and the
technical manual.
Figure 13-6
MAIN MENU
ALARMs / DIAGs
MONITOR SETTINGS
CALIBRATION
FACTORY SETTINGS
Password Protected
3 4 5
Buttons
"Down" Arrow moves menu selection down
"Up" Arrow moves menu selection up
"Right" Arrow acts on current menu item
BACK "Back" Moves back to previous menu
Figure 13-7
TROUBLESHOOTING
Engine Diagnostic Code Summary Screen
i5601E Menu Navigation
Performs the function indicated by a pop-up menu,
if present.
With no pop-up menu showing, briefly press to
display the Lighting & Contrast menu.
With no pop-up menu showing, press and HOLD
to display the MAIN MENU.
ALARMs / DIAGs
Diag Codes
Alarms
Network Status
Network Modes
MONITOR SETTINGS
HOT KEYS LOCK
Units Menu
Language Menu
USER SETTINGS
Tach Range 0-3000
Reset Main1 Time
SPEED
Docking Mode
Depth Offset
Fwd Throt Curv
Default Monitor
Beeper ON Rev Throt Curv
About
Split Range
Prog Shift Delay
Station Protect
CALIBRATION
USER SETTINGS
TROLLING
TROLLING
Troll Mode
Lever
FACTORY SETTINGS
Max Throttle
Eng Display: PORT
Valve CAL
Set idle rpm
Sync: Pwr Train
SETUP TROLL VALVE
Lead Eng Port
T Engage Dry 0.0
RPM ENGAGE 450
Setup TROLL Valve Trans Type
Fixed Shift Dry 0.0
SYSTEM SELECT
0006320
1
1
0.0
N
SPLIT
40%
50%
ZF
0006316
13-29