Toshiba Tosvert VF-AS1 Instruction Manual page 264

2. Basic parameter [3/4]
Communi
Title cation Function
No.
Motor electronic thermal
 0600
protection level 1
Electronic thermal
 0017 protection characteristic
selection
Current/voltage unit
 0701
selection
FM terminal meter
 0005
selection
FM terminal meter
0006

adjustment
AM terminal meter
0670

selection
AM terminal meter
0671

adjustment
0300 PWM carrier frequency

Auto-restart control
0301

selection
Regenerative power
 0302
ride-through control
Dynamic braking
 0304
selection
 0308 Dynamic braking resistance 0.5~1000Ω
Allowable continuous
 0309
braking resistance
*1:  For the adjustment range, see the table on page K-40.
*2: For 200V-55/75kW models and 400V-90kW to 400V-500kW models, the carrier frequency is between 2.5 and 8.0kHz inclusive.
*3: Default values vary depending on the capacity.  See the table of K-48.
*4: Default setting value is adjusted for connection of frequency meters "QS60T". (Between FM and CCA: Approx. 3.6V) (Between AM and CCA: Approx. 3.6V)
Adjustment range
10~100%
Overload
Setting Motor type
protection
0 ○ (protect) × (not stall)
1 Standard ○ (protect) ○ (stall)
Motor
2 × (not protect) × (not stall)
3 × (not protect) ○ (stall)
4 ○ (protect) × (not stall)
5 ○ (protect) ○ (stall)
VF Motor
6 × (not protect) × (not stall)
7 × (not protect) ○ (stall)
0:%, 1:A (ampere)/V (volt)
0~76 *1
-
0~76 *1
-
1.0~16.0kHz (2.5~8.0kHz) *2
0:Disabled
1:At auto-restart after momentary stop
2:When turning ST on or off
3:1+2
4:At start-up
0:Disabled
1:Power ride-through
2:Deceleration stop during power failure
3:Synchronized deceleration/acceleration (synchronized
acceleration/deceleration signal)
4:Synchronized deceleration/acceleration (synchronized
acceleration/deceleration signal+power failure)
0:Disabled
1:Enabled (braking resistance overload detect)
2:Enabled (braking resistance overload not detect)
0.01~600.0kW
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum
setting unit Default Write during
(Panel/Communi setting running
cation)
1/1 100 Enabled
OL stall
1/1 0 Enabled
1/1 0 Enabled
1/1 0 Enabled
1/1 *4 Enabled
1/1 2 Enabled
1/1 *4 Enabled
0.1/0.1 *3 Enabled
1/1 0 Disabled
1/1 0 Disabled
1/1 0 Disabled
0.1/0.1 *3 Disabled
0.01/0.01 *3 Disabled
Vector control
PM
Speed Torque V/f Reference
control
control control
●/● ●/● ● ●
●/● ● ●
5. 14
●/● ●/● ● ●
●/● ●/● ● ●
●/● ●/● ● ●
●/● ●/● ● ●
●/● ●/● ● ●
●/● ●/● ● ● 5. 17
●/● ●/● ● ● 5. 18.1
●/● -/- ● ● 5. 18. 2
●/● ●/● ● ● 5. 19
●/● ●/● ● ● 5. 19
●/● ●/● ● ● 5. 19
5. 14
5. 14
5. 15
5. 16
5. 16
5. 16
5. 16