Dual Detune - Roland Super JX-10 Owner's Manual

5. EDIT PATCH PARAMETERS
The Tones and Patch Memories written in the JX-10's internal memory or in the cartridge memory can be edited to
your taste. This editing does not automatically rewrite the previous data. To write the edited data, take an
appropriate writing procedure as explained on page xxxx
a. Editing a Patch Memory
Each of the A-1 to H-8 Patch Memories consists of 39 different Factors and changing the values of the Factors will
edit a Patch Memory. Editing is quite simple; the value of each Factor has two figure number, so use the
appropriate number to call the Factor whose value you wish to change, then change it.
Patch Factors can be recalled through the numeric keypad 0 – 9.
Patch Factors can be assigned to C1/C2 sliders, pushing C1/C2 buttons and selecting the relevant Patch Factor
through α Dial. In this way, two selected Patch Factors can be controlled in real time.
Parameter
#
11 UPPER/LOwER BALANCE
12

DUAL DETUNE

13 Upper split point
14 Lower split point
15 Portamento Time
16 Bender ranGe
17 key mode
Range
00 to 99
-50 to 00 to +50
E1 to g7
E1 to g7
00 to 99
2, 3, 4, 7, 12
Up whole
Lo whole
Dual
Split
t.voice
x-fade
Roland JX-10 Manual – Firmware ver 3.00 ADDENDUM
Pag. 17 of 53
Description
This Factor determines the volume balance of the
Upper and the Lower. When the value is about 50, the
volumes of the both sections are the highest, and as
the value increases, the Lower volume decreases, the
Upper volume remaining the highest. That is, when the
value in the Display is 99, only the Upper sound will be
heard. When the value is smaller than 50, the opposite
effect will be obtained.
This Factor can detune the Lower sound from the
Upper sound. At "+" value, the Lower sound is raised,
at zero, the pitch is the same as the Upper, and at "-"
value, it is lowered.
The Split Point set with the Quick Edit is restricted to
the lowest note of the Upper section. Here, however,
these two Factors are used for setting two different
Split Points; the lowest note of the Upper section, and
the highest note of the Lower section. The value and
the note name. The lowers note is E1, the middle C is
C4 and the highest is G7. ("+" indication represents #.)
This Factor adjusts the Portamento time.
Higher value is the longer Portamento time.
This Factor sets the maximum effect of the Bender.
The value in the Display represents semi-tone. 2 is
major 2 , 3 is minor 3 , 4 is major 3
nd rd
and 12 is perfect octave.
The Key Modes which can be selected with the Quick
Edit Function are restricted to four modes; Upper
Whole, Lower Whole, Dual and Split. Here, however,
two more Key Modes, altogether 6 modes can be set.
T. VOICE and X-FADE can be selected by rotating the
α Dial counterclockwise, and other modes can be
selected by rotating it clockwise.
Touch Voice Select Mode (T. VOICE)
In this mode, either the Upper or Lower Tone is output
depending how you play the keyboard. That is, when
you play the keyboard hard, the Upper Tone Is
selected, and when you play softly, the Lower Tone
sounds. As shown in the left picture, the key touch
pressure that selects the Upper or the Lower Tone
changes depending on the Upper Split Point (= Factor
13). When the Split Point is set to higher note, stronger
key touch will be needed for obtaining the Upper Tone.
Cross Fade Mode (X-FADE)
This is a kind of Dual mode.
In this mode, the volume of the Lower Tone decreases
by stronger key touch, and the volume of the Upper
Tone decreases by weaker key touch. This mode,
therefore can be effectively used to change the volume
balance of the Tones by changing the playing manners
when you are using different Tones for the Upper and
the Lower.
, 7 is perfect 5
rd th