Cisco Catalyst 3030 Command Reference Manual page 46

auto qos voip
If this is the first port on which you have enabled auto-QoS, the auto-QoS-generated global configuration
commands are executed followed by the interface configuration commands. If you enable auto-QoS on
another port, only the auto-QoS-generated interface configuration commands for that port are executed.
When you enable the auto-QoS feature on the first port, these automatic actions occur:
QoS is globally enabled (mls qos global configuration command), and other global configuration
•
commands are added.
When you enter the auto qos voip cisco-phone interface configuration command on a port at the
•
edge of the network that is connected to a Cisco IP Phone, the switch enables the trusted boundary
feature. The switch uses the Cisco Discovery Protocol (CDP) to detect the presence or absence of a
Cisco IP Phone. When a Cisco IP Phone is detected, the ingress classification on the port is set to
trust the QoS label received in the packet. When a Cisco IP Phone is absent, the ingress classification
is set to not trust the QoS label in the packet. The switch configures ingress and egress queues on
the port according to the settings in
When you enter the auto qos voip cisco-softphone interface configuration command on a port at
•
the edge of the network that is connected to a device running the Cisco SoftPhone, the switch uses
policing to decide whether a packet is in or out of profile and to specify the action on the packet. If
the packet does not have a DSCP value of 24, 26, or 46 or is out of profile, the switch changes the
DSCP value to 0. The switch configures ingress and egress queues on the port according to the
settings in
When you enter the auto qos voip trust interface configuration command on a port connected to the
•
interior of the network, the switch trusts the CoS value for nonrouted ports in ingress packets (the
assumption is that traffic has already been classified by other edge devices). The switch configures
the ingress and egress queues on the port according to the settings in
You can enable auto-QoS on static, dynamic-access, and voice VLAN access, and trunk ports. When
enabling auto-QoS with a Cisco IP Phone on a routed port, you must assign a static IP address to the IP
phone.
When a device running Cisco SoftPhone is connected to a switch or routed port, the switch supports only
Note
one Cisco SoftPhone application per port.
After auto-QoS is enabled, do not modify a policy map or aggregate policer that includes AutoQoS in its
name. If you need to modify the policy map or aggregate policer, make a copy of it, and change the
copied policy map or policer. To use the new policy map instead of the generated one, remove the
generated policy map from the interface, and apply the new policy map.
To display the QoS configuration that is automatically generated when auto-QoS is enabled, enable
debugging before you enable auto-QoS. Use the debug auto qos privileged EXEC command to enable
auto-QoS debugging. For more information, see the
To disable auto-QoS on a port, use the no auto qos voip interface configuration command. Only the
auto-QoS-generated interface configuration commands for this port are removed. If this is the last port
on which auto-QoS is enabled and you enter the no auto qos voip command, auto-QoS is considered
disabled even though the auto-QoS-generated global configuration commands remain (to avoid
disrupting traffic on other ports affected by the global configuration). You can use the no mls qos global
configuration command to disable the auto-QoS-generated global configuration commands. With QoS
disabled, there is no concept of trusted or untrusted ports because the packets are not modified (the CoS,
DSCP, and IP precedence values in the packet are not changed). Traffic is switched in pass-through mode
(packets are switched without any rewrites and classified as best effort without any policing).
Cisco Catalyst Blade Switch 3030 Command Reference
2-18
Table 2-2
Table 2-2 and Table 2-3.
Chapter 2 Cisco Catalyst Blade Switch 3030 Cisco IOS Commands
and Table 2-3.
Table 2-2
debug auto qos command.
and Table 2-3.
78-17262-01