Tightening Torque - Brother DPC-8060 Service Manual

Tightening Torque

Location of screw
Ejector solenoid
Main motor
T1, MP, Register solenoid
Gear plate
Main shield
Ground wire
SW holder
Under bar
Paper feed unit
HVPS
LVPS
Base plate
Main PCB
Shield cover
Scanner plate
PE EG sensor
MP PE sensor
MP feed frame
Regist frame (2), MP tray
unit (2), Chute 2 (2)
Inner chute
Panel PCB
Cover
FG wire
Joint cover ASSY ALFB
Speaker hold spring
Side cover R ALFB
Side cover L ALFB
Driver PCB shield ALFB
Driver PCB shield ALFB
FB motor
FB FG harness
Drive plate ASSY
Pulley ASSY ALFB
Lock lever A
Lock lever B
Scanner top cover ASSY
Scanner unit
Screw type
Taptite, bind B M3 x 10
Taptite, cup S M3 x 6
Taptite, bind B M3 x 10
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Screw, pan (S/P washer) M3.5 x 6
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, cup S M3 x 6 SR
Taptite, cup S M3 x 6 SR
Taptite, cup S M3 x 6
Taptite, bind B M3 x 8
Taptite, bind B M3 x 8
Taptite, bind B M3 x 8
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, cup B M3 x 8
Taptite, bind B M4 x 12
Taptite, cup S M3 x 6 SR
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, bind B M4 x 12
Taptite, bind B M3 x 8
Taptite, cup S M3 x 6 SR
Screw, pan (S/P washer) M3 x 6
Taptite, cup S M3 x 6
Taptite, pan B M3 x 8
Taptite, B M3 x 6
Taptite, B M3 x 6
Taptite, B M3 x 6
Taptite, cup B M4 x 12
Taptite, cup B M4 x 20
5-2
Q'ty Tightening torque
N•m (kgf•cm)
1 0.5 ±0.1(5±1)
4 0.7 ±0.1(7±1)
3 0.5 ±0.1(5±1)
8 0.9 ±0.1(9±1)
3 0.9 ±0.1(9±1)
1 0.5 ±0.05 (5±0.5)
1 0.8 ±0.1(8±1)
4 0.7 ±0.1(7±1)
8 0.8 ±0.1(8±1)
2 0.8 ±0.1(8±1)
2 0.8 ±0.1(8±1)
9 0.8 ±0.1(8±1)
4 0.75 ±0.1(7.5±1)
4 0.75 ±0.1(7.5±1)
6 0.7 ±0.1(7±1)
1 0.5 ±0.1(5±1)
1 0.5 ±0.1(5±1)
2 0.5 ±0.1(5±1)
6 0.7 ±0.1(7±1)
6 (7) 0.8 ±0.1(8±1)
3 0.5 ±0.1(5±1)
6 0.8 ±0.1(8±1)
1 0.75 ±0.1(7.5±1)
4 0.8 ±0.1(8±1)
1 0.8 ±0.1(8±1)
2 0.8 ±0.1(8±1)
2 0.8 ±0.1(8±1)
2 0.4 ±0.05(4±0.5)
1 0.75 ±0.1(7.5±1)
2 0.7 ±0.1(7±1)
1 0.8 ±0.1(8±1)
4 0.5 ±0.1(5±1)
2 0.4 ±0.05(4±0.5)
2 0.4 ±0.05(4±0.5)
1 0.4 ±0.05(4±0.5)
6 0.8 ±0.1(8±1)
2 0.8 ±0.1(8±1)
Confidential