Denon AVR-2805 Operating Instructions Manual page 9

• When making connections, also refer to the eperating instructions of the ether components.
• The signals input to the celor difference (component) video jacks are net outputs to the VIDEO output jack (yeliew) or the S-Videe output jack.
• Some vide() sources with compenent video outputs are labeled Y, CB, CR, or Y, Pb, Pr, er Y, R-Y, B>4 These terms all refer to component vide()
color difference eutput
• The function assigned to the component video input can be changed at the system setup. For details, see "Setting the Video Input Mede'.
(See page 41 )
'-COMPONENT
VIDEO OUT
%@@
®6eee° " ..............
.... == ] ] ,,_*- , . ..................
o@®®©©@@i®© o
I Connecting a DVD player ]
DVD IN jacks
• Connect the DVD player's color difference (component) video output jacks
(COMPONENT VIDEO OUTPUT) to the COMPONENTVIDEO-1 IN jack using
x,,, v,. cords.
• In the same way, another video source with component video outputs such
I ... ,o.stun.r. etc., ,com.n.t, v=.
Y Ca OR MONITOR OUT jack
_, t I _®@',@ I
• Connect the TV's color difference (component) video input jacks
_ (COMPONENT VIDEO INPUT)to the COMPONENT MONITOR OUT
jack using 75 _/ohrns coaxial video pin-plug cords.
• The color difference input jacks may be indicated differently on
some TVs, monitors or video components CCR, CB and Y", "R-
__ Y, B-Y and Y", "Pr, Pb and Y", etc.). For details, carefully read the
operating instructions included with the TV or other component.
MONITOR OUT jacks
,@@@@@@®@®°
i
5
!£i£ £i :iBi£!i £iii!!!!!!!!!!!!!!!!ii i
!i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i !i
With the AVR-280B/985, the Video signal and the S-video signal
which were inputted are converted mutually. And also the
Video signal and the S-Video signal which were inputted are
converted into a higher quality.
The flow of the
This unit's input jacks This unit's output jacks
this unit's internal
e60 1 signals. : @@B
(ColorDiffrenceVideo jackl IColorDiffrenceVideo jack)
..... @
..... (S-Video jack) (S-Videojack)
The AVR-2805/985 is equipped with a function fer up-converting
video signals.
Because of this, the AVR-2805/985's MONITOR OUT jack can be
connected to the monitor (TV) with a set ef canes offering a higher
quality connectien, regardless ef hew the player and the AVR-
2805/985's video input jacks are cennected.
Generally speaking, cennections using the component vide() jacks
effer the highest quality playback, fe/ewed by connectiens using the
S-Videe jacks, then connectiens using the regular vide() jacks
(yellow).
NOTE:
Dewn-converting from the component vide() signal te the S-Video
and composite video signal is not possible, so when not using the
component video monitor output terminal connect the player using
the S-Video or composite vide() input terminal.
Cautions on the video conversion function:
When the component video terminals are used to connect the AVR-
2805/985 with a TV (or moniter, projector; etc.) and the video (yeliew)
er S video terminals are used to connect the AVR-2B05/985 with a
VTR, depending en the combination of the TV and VTR the picture
may flicker in the horizental direction, be distorted, be out of sync or
not display at all when playing vide() tapes.
If this happens, connect a cemmercially available video stabilizer, etc.,
with a TBC (time base correcter) function between the AVR-2BOB/9B5
and the VTR, er if yeur VTR has a TBC function, turn it en.