Add Token; Delete Token; Token Status; User Rf Keyfobs - Bosch Solution 16plus Installation Manual

Solution 16
plus Installation Manual

Access > Token >

Add Token

This command allows the Installer or Master User to assign
a Token ID for each user. Only one Token can be assigned to
each user. To change a Token for an existing user you will
need to first delete the old Token before adding the new one.
See MENU 1-2-1 — Delete Token
Enter [MENU] + [1] + [2] + [0] and use the up and down arrows
1)
to highlight the user in the list then press [OK]. The system will
only list users that dont already have Tokens assigned.
Ur001 John Smith
Ur002 Debbie Smith
Ur003 User 3 Name
Press  OK or MENU
2) Swipe the token card past the reader. As you swipe the token,
the reader will sound a single beep to confirm that the token
has been learnt.
To add token for Ur001
John Smith present new
token at R001
Press OK or MENU
i
If the Add Token command is initiated from a keypad that does
not have a built in reader, you will need to select a reader from
the list before proceeding. Swipe the Token at the selected reader.
Note
Access > Token >

Delete Token

This command allows the Installer or Master User to delete
Token IDs which have been programmed into the system.
1) Enter [MENU] + [1] + [2] + [1] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that have Tokens assigned to them.
Ur001 John Smith
Ur002 Debbie Smith
Ur003 User 3 Name
Press  OK or MENU
Press [OK] to delete the token or press [MENU] to exit without
2)
saving.
To delete token for Ur001
John Smith press OK
Press OK or MENU
5-4
Access Programming

-
MENU 1-2-0
 
-
MENU 1-2-1
 
Access > Token >

Token Status

This command allows the Installer or Master User to identify who
a Token has been assigned to. You will need to have the token
in order to do the test. This command can only be performed at
a prox keypad.
1) Enter [MENU] + [1] + [2] + [2]. The system will prompt you to
swipe the token to be checked.
Present token to be
Identified at R001
Press OK or MENU
2) Present the token to the keypad, you will hear a confirmation
beep and the display will show the token status.
Token belongs to Ur002
Debbie Smith
Press OK or MENU
To exit, press [OK] or [MENU].
3)
U SER RF KEYFOBS
This section outlines how to add and delete RF keyfobs. RF
Keyfobs provide an alternate method for users to turn the
system on and off.
There are two methods for adding RF Keyfobs, Direct Entry and
Learn Mode. The system will prompt for the appropriate method
depending on the Receiver type fitted to the system.
The RF Keyfob must be compatible with the RF Receiver that has
been programmed in MENU 3-5-0 — Input Type.
Refer to MENU 6-2-2 — RF Device Options to configure the
following preferences for RF Keyfobs.
™ Audible RF Keyfob Panic,
™ Report RF Keyfob Panic and
™ RF Keyfob 'Part On' Arming Allowed.
RF Keyfobs will follow all user settings.
Access > RF Keyfob >

Add Keyfob

This menu allows the Installer or a Master User to assign an RF
Keyfob to a user. All users can have an RF Keyfob assigned if
required.
Keyfob Direct Entry Mode
1) Enter [MENU] + [1] + [3] + [0] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that dont already have an RF Keyfob assigned.
-
MENU 1-2-2
 
-
MENU 1-3-0
 
Bosch Security Systems 05/10 BLCC100I