Programming Examples; Opening A Door Using A Single Digit Code; Opening A Garage Door Using A 4 Button Rf Keyfob; Auto Arming An Area - Bosch Solution 16plus Installation Manual


T
his section includes a number of programming examples
detailling how to implement some common installation
functionality.
Examples are provided to show;
™
How to Open a Garage Door using a Single Digit Code.
™
How to Open a Garage Door using a 4 Button Keyfob.
™
How to set Auto Arming for an Area.
™
How to operate an Output using a Schedule
™
How to Use a Reader to Unlock a Door.
™
How to Use a Reader to Unlock a Door and Disarm Area 1.
™
How to Use a Reader to Unlock a Door and Arm/Disarm.
™
How to use Call Line Identification.
™
How to send SMS Reports.

Opening a Door using a Single Digit Code

The Solution 16 can be used to operate an electrically
plus
controlled door using a single digit code. The example assumes
User 10 and Output 5 are being used. (Output 5 is located on the
CM110 Output Expander).
Procedure
1) Set User Pin Code Length MENU 1-5-0 = 0
(0 = Variable Length)
Set User 10 - PIN Code MENU 1-1-2 = 5
2)
Set User 10 - Area Assignment MENU 1-4-1 = NNNNNNNN
3)
4) Set Output 5 - Event Type MENU 4-1-1 = 56
(56 = Follow Pin)
5) Set Output 5 - Event Assignment MENU 4-1-2 = 10
(10 =User Number)
6) Set Output 5 - Output Polarity MENU 4-1-3 = 4
(4 = Normally Open One Shot Low)
Set Output 5 - Time Parameter MENU 4-1-4 = 000 000 005 000
7)
(5 seconds)
8) Enable Output 5 - Output Options MENU 4-1-5 = Display Status
Message
Bosch Security Systems 05/10 BLCC100I

Programming Examples

Wire Output 5 to the appropriate Door Controller input. Each
time button 5 on the keypad is pressed the door will activate.

Opening a Garage Door Using a 4 Button RF Keyfob

The following example show how to configure the Solution
16 to allow control of a grage door as well as arm and disarm
plus
functions using a 4 Button Keyfob. The example assumes User
10 and Output 5 are being used. (Output 5 is located on the
CM110 Output Expander).
Procedure
1) Set RF Receiver Type MENU 3-5-0 = D
(D = DS Type)
2) Assign Keyfob to User 10 MENU 1-3-0 = 123456789
Set Output 5 - Event Type MENU 4-1-1 = 53
3)
(53 = RF Keyfob Function 1)
4) Set Output 5 - Event Assignment MENU 4-1-2 = 1
(1 =Area Number)
5) Set Output 5 - Output Polarity MENU 4-1-3 = 4
(4 =Normally Open One Shot Low)
6) Set Output 5 - Time Parameter MENU 4-1-4 = 000 000 005 000
(5 seconds)
Enable Output 5 - Output Options MENU 4-1-5 = Display Status
7)
Message.

Auto Arming an Area

The Solution panel can be configured to automatically arm and
or disarm an area automatically if required.
Procedure
To setup an Auto Arming time, select a schedule that is not
being used, and program the schedule name to something
convenient. Set the start time for the schedule to the arming
time you require. The stop time should be set to 12:00am or --:--
am, which prevents the system from auto disarming.
Now set the Schedule Function, MENU 7-5-3 to Area On/Off and
the Schedule Index, MENU 7-5-4 to correspond to the area to
operate. If an index of 0 is used then arming will occur for all
areas. Finally select the days of the week you wish auto arming
to occur in MENU7-5-2
SECT ION 1 2
12-1