Ras Security Pin; Log Threshold; Ring Count - Bosch Solution 16plus Installation Manual

For higher security the panel can be configured to always
use this number for callback verification when establishing a
SolutionLink remote access connection. The following steps
outline the callback procedure.
Step 1) Use Solutionlink RAS to call panel from remote computer.
Step 2) Panel will answer, acknowledge the request and then hang
up.
Step 3) Panel will then dial the callback number.
Step 4) SolutionLink will answer the call and establish a RAS session.
i See MENU 5-3-4 to force Callback Verification for every RAS
Session.
Note
Press [MENU] + [5] + [3] + [0]. The keypad will display the
1)
current Call Back telephone number if programmed.
Call Back Number P001
Press  0-9 OK to SAVE
2) Using the numeric keys, enter all the digits of the Call Back
number. You can change a single digit by scrolling the cursor
left or right. For special characters including, pause, * or #, use
the up and down arrow keys.
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
i
You must add any area codes or other special access numbers
which are required to be able to dial the remote computer from
the panel phone line. Simply add these numbers before the Call
Note
Back number.
Comms > Remote Access >

RAS Security PIN

The RAS security PIN programmed here must match the security
PIN programmed in the customer file of the SolutionLink RAS
upload/download database otherwise a connection to the
panel cannot be established.
1) Press [MENU] + [5] + [3] + [1]. The keypad will display the
current RAS Security PIN. The default = 12345678.
RAS Security PIN
12345678
Press 0-9 OK to SAVE
2) Using the numeric keys, enter all the digits of the new RAS
security PIN. You can change a single digit by scrolling the
cursor left or right.
Press [OK] to save and exit or press [MENU] to exit without
3)
saving.
Bosch Security Systems 05/10 BLCC100I
MENU 5-3-1

1 2 3 4 5 6 7
Solution 16
plus

Comms > Remote Access >

Log Threshold

The control panel can store up to 256 system events in its built
in history log. A newly installed panel will have 100% of its log
space available for new events (0% full). As the panel starts to
store events in the log, the capacity for new events is reduced.
The history log is 100% full when event 256 is stored in memory.
Event 257 will start to overwrite the oldest events in the log.
When the Log Threshold option is programmed, the panel will
send a 'Log Threshold' report to the base station when the event
log reaches the percentage as set since the last SolutionLink
session.
If the event log reaches 100% capacity before a SolutionLink RAS
session is established then the system will send a 'Log Overflow'
report. The panel will also log these events in its memory.
1) Press [MENU] + [5] + [3] + [2]. The keypad will display the
current threshold limit. The default is 70% full.
Log Threshold N001
070 Percent
Press 0-9 OK to SAVE
2) Using the numeric keys enter the new threshold limit, then
press [OK] to save and exit or press [MENU] to exit without
saving. There is no need to enter the % symbol.
i
Each time a SolutionLink RAS session is established with the
panel, the log information will be uploaded to the SolutionLink
database where it can be reported on or archived for later use
Note
Comms > Remote Access >

Ring Count

0 = No Answer
1 to 15 = Answer Ring Count
8 This menu sets the number of rings the panel will wait until
answering an incoming call. Programming a zero will stop the
panel from answering any incoming calls.
i In Software version 1.02 and higher, the ring count has been
changed to make it easy for new users to lean and simpler to use
when establishing a remote connection. In earlier versions, the
Note
panel would count rings as follows: RING..RING.......RING..RING
would be counted as 1 ring. The panel will now count rings as
follows: RING..RING would be counted as 1 ring. Occasionally,
you will hear half a ring at the moment the line is switched
through to the premises. In this case the panel will count the
rings as follows: RING.......RING..RING would be counted as 1
.
ring.
Press [MENU] + [5] + [3] + [3]. The keypad will display the
1)
current ring count.
Ring Count P001
15-15 Rings
Press  0-9 OK to SAVE
Installation Manual Comms Programming



MENU 5-3-2
7 0 %
MENU 5-3-3
20
9-7