Solid Top Range Hob; Electric Oven; Replacing Components; Reminders For Replacing Components - KBS Gastrotechnik 700 Series Instructions For Installation, Operation And Maintenance

• Insufficient voltage or incorrect electric connection of the ap-
pliance.
• Defective energy regulator
• Element defective or not properly connected (burnt internal
heating element).
Heating cannot be adjusted
Possible causes:
• Temperature thermostat defective.
17.2

SOLID TOP RANGE HOB

The hotplate does not heat.
Possible causes:
• Check the fuses.
• Power supply main switch disconnected.
• Insufficient voltage or incorrect electric connection of the ap-
pliance.
• Temperature thermostat defective.
• Element defective or not properly connected (burnt internal
heating element).
Heating cannot be adjusted
Possible causes:
• Temperature thermostat defective.
17.3

ELECTRIC OVEN

The appliance does not heat.
Possible causes:
• Temperature thermostat defective.
• Heating elements defective.
• Safety thermostat tripped.
Heating cannot be adjusted
Possible causes:
• Temperature thermostat defective.

18 REPLACING COMPONENTS

REMINDERS FOR REPLACING COMPONENTS.

• Disconnect the appliance electric supply, if present, before
carrying out any operation.
• After replacing a gas system component, check for gas leaks
at connection points.
• After replacing an electrical system component, check it is
correctly wired.
• When replacing the radiant hotplates, handle and re-assem-
ble parts with the utmost care.
18.1

GLASS CERAMIC HOB

Replacing the radiant hotplates
• Remove the control panel.
• Remove the tray by tilting it downwards and pulling it out.
• Replace the faulty component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the thermostat
• Remove the control panel.
• Remove the tray by tilting it downwards and pulling it out.
• Remove the bulb from its seat and replace the faulty part.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Glass ceramic hob
• In the event the glass ceramic hob is broken, contact our
company to have it replaced.
18.2 SOLID TOP RANGE HOB
Replacing the radiant hotplates
• Remove the control panel.
• Remove the tray by tilting it downwards and pulling it out.
• Replace the faulty component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the thermostat
• Remove the control panel.
• Remove the tray by tilting it downwards and pulling it out.
• Remove the bulb from its seat and replace the faulty part.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the fan and thermal fuse
• Remove the control panel.
• Remove the fan lid.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
18.3 ELECTRIC OVEN
Replacing the knob and indicator light
• Remove the control panel.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the working thermostat and safety thermostat.
• Remove the control panel.
• Remove the bulb from its seat on the side of the oven.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.
Replacing the heating element
• Remove the oven floor (only for lower heating elements).
• Undo the screw securing the element to the oven and pull the
element out by approx. 10 cm.
• Remove and replace the component.
• Re-assemble all parts. For assembly, proceed in reverse or-
der.

19 CLEANING THE INTERIOR

• Check the condition of the inside of the appliance.
• Remove any built-up dirt.
• Check and clean the fumes exhaust system.

20 MAIN COMPONENTS

20.1 SOLID TOP RANGE HOB
• Indicator light
• Fan
• Cooking zone heating element
20.2 GLASS CERAMIC HOB
• GLASS CERAMIC HOB
7