Brother DCP-1510 Service Manual page 33

3 3 . . 2 2 E E r r r r o o r r M M e e s s s s a a g g e e s s
Cartridge Error Cartridge Error
C C o o o o l l i i n n g D
C C ov
Document Jam Document Jam
Drum ! Drum !
Drum End Soon Drum End Soon
Jam Inside 1 Jam Inside 1
Jam Inside 2 Jam Inside 2
Jam Inside 3 Jam Inside 3
Jam Tray Jam Tray
Machine Error** Machine Error**
No Drum No Drum
No Paper No Paper
No Toner No Toner
O O u u t t o o f f M M e e m m o o r r y y
F F i i r r s s t t l l i i n n e e S S e e c c o o n n d d l l i i n n e e
Put the Toner Cartridge Put the Toner Cartridge
back in back in
g Do o w w n n W W a a i i t f t fo o r a r a w w h h i i l l e e
ove e r i r is O s Op p e e n n C C l l o o s s e t e th h e T
Clear the scanner jam, Clear the scanner jam,
then press the Stop Key. then press the Stop Key.
Open the Scanner Cover Open the Scanner Cover
and Top Cover and slide and Top Cover and slide
the green tab across the the green tab across the
Drum Unit several times. Drum Unit several times.
Open the Scanner Cover and Open the Scanner Cover and
Top Cover, pull out the Drum Top Cover, pull out the Drum
Unit and remove the jammed Unit and remove the jammed
paper, then press Start. paper, then press Start.
Open the Scanner Cover Open the Scanner Cover
and remove the jammed and remove the jammed
paper, then press Start. paper, then press Start.
Remove the jammed Remove the jammed
paper, then press Start. paper, then press Start.
Remove the jammed paper Remove the jammed paper
from Tray then press Start. from Tray then press Start.
Open the Scanner Cover Open the Scanner Cover
and Top Cover, then install and Top Cover, then install
the Drum Unit. the Drum Unit.
Load paper, then press Load paper, then press
Start. Start.
Open the Scanner Cover Open the Scanner Cover
and Top Cover, then install and Top Cover, then install
the Toner Cartridge. the Toner Cartridge.
Pr Pre e s s s s St Sto o p p K K e e y y
The new toner sensor could not The new toner sensor could not
detect the new toner cartridge detect the new toner cartridge
correctly. correctly.
Cooling down the machine to Cooling down the machine to
protect the inside of the machine. protect the inside of the machine.
The top cover sensor detected that The top cover sensor detected that
e To o p C p Co o v v e e r r . .
the top cover was open. the top cover was open.
The document is too long or cannot The document is too long or cannot
be fed. be fed.
Detected discharge that may be Detected discharge that may be
attributable to dirty corona wire on attributable to dirty corona wire on
the drum unit. the drum unit.
The number of pages printed with the The number of pages printed with the
- -
drum unit is reaching the life limit. drum unit is reaching the life limit.
The eject sensor does not detect The eject sensor does not detect
paper pass after the paper printing paper pass after the paper printing
position sensor detected the paper position sensor detected the paper
pass. pass.
The eject sensor remains ON The eject sensor remains ON
(paper pass detected) even after (paper pass detected) even after
the paper printing position sensor the paper printing position sensor
detected the end of paper pass. detected the end of paper pass.
When the power switch was turned When the power switch was turned
ON, the eject sensor detected ON, the eject sensor detected
paper pass. (Cannot determine paper pass. (Cannot determine
whether the top cover is open or whether the top cover is open or
whether it is a paper jam.) whether it is a paper jam.)
The paper feed sensor does not The paper feed sensor does not
detect paper pass even after the detect paper pass even after the
paper has been fed for the specified paper has been fed for the specified
time. time.
A machine error occurred. A machine error occurred.
- -
Refer to error codes for "**". Refer to error codes for "**".
Detected that the drum unit was not Detected that the drum unit was not
set by GRID current error. set by GRID current error.
When printing from the paper tray, When printing from the paper tray,
the paper feed sensor detected that the paper feed sensor detected that
there was no paper set in the paper there was no paper set in the
tray. tray.
The new toner sensor terminal The new toner sensor terminal
detected that the toner cartridge detected that the toner cartridge
was not set by the terminal was not set by the terminal
conduction failure. conduction failure.
There is insufficient memory to There is insufficient memory to
expand PC print data. expand PC print data.
1-18 1-18
Refer Refer
D D e e s s c c r r i i p p t t i i o o n n
A200 A200
A300 A300
7D00 7D00
- -
paper
C700 C700
to: to:
4F01 4F01
6801 6801
6001 6001
6A00 6A00
4000 4000
7000 7000
7100 7100
7300 7300
6200 6200
9302 9302
6101 6101
Confidential Confidential