Brother DCP-1510 Service Manual page 175

1.3.16 1.3.16 Fine-tune sc Fine-tune scanning position (fu
<Function> <Function>
This function is used to adjust the scanning start/end positions for the ADF and the document This function is used to adjust the scanning start/end positions for the ADF and the document
scanner unit. scanner unit.
<Operating Procedure> <Operating Procedure>
(1 (1) ) Nu
(2) "SCAN (2)
(3) (3) The curre
(4) (4) Pre
(5) (5) Press the [O
1.3.17 Acquire white leve 1.3.17 Acquire white level data and se
<Function> <Function>
This function is used to obtain the white level of the CIS unit, and store this data and the scan This function is used to obtain the white level of the CIS unit, and store this data and the scan
area in the EEPROM of the main PCB. area in the EEPROM of the main PCB.
<Operating Procedure> <Operating Procedure>
(1 (1) ) Nu
(2) If an erro (2)
(3) Press the [S (3)
anning position (function code:
Nume meri ric ke c key pa y pad mo d mode dels ls
Press the [5] and [4] buttons in this order in the initial state of maintenance mode. Press the [5] and [4] buttons in this order in the initial state of maintenance mode.
Non-numeric key pad models Non-numeric key pad models
Pres Pr ess th s the [ e [ ] or ] or [ [ ] bu ] butt tton t
[OK] button. [OK] button.
"SCAN ST START ART ADJ." ADJ." is di is displaye
After two seconds, " After two seconds, " : ADF : ADF
to a to adj djus ust it t its st s star art pos t positi ition on. Pre
scanner unit. scanner unit.
The current scann nt scanning posi ing position comp
(Compensation levels can be adjusted in 101 steps from 50 to -50.) (Compensation levels can be adjusted in 101 steps from 50 to -50.)
Press th ss the [ e [ ] button t ] but ton to adj o adjust t
the [ [ the ] bu ] button tton to a to adju djust i st it to t
Press the [OK] button. " K] button. "Accept Accepted" is disp
the initial state of maintenance mode. the initial state of maintenance mode.
l data and set CIS scan area (f
Nume meri ric ke c key pa y pad mo d mode dels ls
Press the [5] button twice in the initial state of maintenance mode. Press the [5] button twice in the initial state of maintenance mode.
Non-numeric key pad models Non-numeric key pad models
Pres Pr ess th s the [ e [ ] or ] or [ [ ] bu ] butt tton t
[OK] button. [OK] button.
If an error occu r occurs in the m rs in the machine
P P r r e e s s s s [ [ ] ] , , [ [ ] ] , , [ [ ] ] a a n n d d [ [
If there is no error in the machine, proceed to step (3). If there is no error in the machine, proceed to step (3).
Press the [Start] but tart] button. "SCAN ton. "SCANNER AREA SET" is dis
level data is obtained. level data is obtained.
After several seconds, the After several seconds, the compensation value for the w
stored in the EEPROM, and the machine returns to the initial state of maintenance stored in the EEPROM, and the machine returns to the initial state of maintenance
mode. If any error is detected during this operation, "SCANNER ERROR" is displayed mode. If any error is detected during this operation, "SCANNER ERROR" is displayed
on the LCD. on the LCD.
In this case, turn the power switch of the machine OFF and do repairs in reference to In this case, turn the power switch of the machine OFF and do repairs in reference to
chapter 1. chapter 1.
4-24 4-24
nction code: 54) 54)
on to di o disp spla lay "M y "MAI AINTE NTENA NANC
splayed on d on the LC the LCD. D.
: FB" is displayed on the LCD. Select the preferred item : FB" is displayed on the LCD. Select the preferred item
. Press [ ss [ ] to s ] to sel elec ect the A t the ADF a
tion compensati ensation level i on level is displ
ust the co he compe mpensa nsatio tion lev n level to
t to the n he nega egativ tive di e direc rectio tion. n.
ed" is displayed on t layed on the LCD, and t
t CIS scan area (function code: 55)
on to di o disp spla lay "M y "MAI AINTE NTENA NANC
achine, "ME AF ST , "ME AF STOP" is d OP" is display
] ] b b u u t t t t o o n n s s i i n n t t h h i i s s o o r r d d e e r r . .
NER AREA SET" is displayed on th
compensation value for the white level data/scanning wid
NCE 54 E 54" on " on th the LC e LCD an D and pr d pres
DF and [ nd [ ] to se ] to sele lect t ct the do he docu
s displayed on the LC ayed on the LCD. D.
el to the p the posi ositiv tive di e direct rection o ion or pre
he LCD, and the machi he machine return ne returns to
unction code: 55)
NCE 55 E 55" on " on th the LC e LCD an D and pr d pres
isplayed on the ed on the LCD. LCD.
played on the LCD, and the wh e LCD, and the white
hite level data/scanning width is
Confidential Confidential
ess th s the e
cume ment nt
r press ss
s to
ess th s the e
ite
th is