Brother DCP-1510 Service Manual page 162

Refer to the separate manual for details of worker switches. Refer to the separate manual for details of worker switches.
<Operating Procedure> <Operating Procedure>
(1 (1) ) Nu
(2) "WSW (2)
(3) (3) The di
(4) When cha (4)
(5) When worke (5)
Note: Note:
• • T T o cancel operation and
• • After ente
Nume meri ric ke c key pa y pad mo d mode dels ls
Press the [1] and [0] buttons in this order in the initial state of maintenance mode. Press the [1] and [0] buttons in this order in the initial state of maintenance mode.
Non-numeric key pad models Non-numeric key pad models
Pr Pres ess th s the [ e [ ] or ] or [ [ ] butt tton t ] bu
[OK] button. [OK] button.
"WSW00" 00" is di is displ splaye ayed on t d on the L
Numeric key pad models Numeric key pad models
Enter the worker switch number that you want to change the setting. Enter the worker switch number that you want to change the setting.
Non-numeric key pad models Non-numeric key pad models
Pres Pr ess th s the [ e [ ] or [ ] or [ ] bu ] butt tton t
the LCD and press the [OK] button. the LCD and press the [OK] button.
The displ splay sho ay shown bel wn below ap ow appear
S S e e l l e e c c t t o o r r N N o o . . 1 1 S S e e l l e e c c t t o o r r N N o o . . 8 8
WSWXX = 0 0 0 0 0 0 0 0 WSWXX = 0 0 0 0 0 0 0 0
Numeric key pad models Numeric key pad models
Pr Pres ess th s the [ e [ ] or [ ] or [ ] butto ] bu tton to m
setting by pressing the [1] or [0] button. setting by pressing the [1] or [0] button.
Non-numeric key pad models Non-numeric key pad models
Set t t the Se he va valu lue b e by p y pre ress ssin ing t g the
When changing the s nging the setting i etting is complet
value is stored in the EEPROM, an value is stored in the EEPROM, and the LCD returns to the ready
number entry ([WSW00]). number entry ([WSW00]).
When worker switch set r switch setting is comp ting is completed, pre
machine to the initial state of maintenance mode. machine to the initial state of maintenance mode.
o cancel operation and return to the initial return to the initial state of maintenance
[Stop/Exit] button. [Stop/Exit] button.
After entering the first digi ring the first digit of the number
the two digits firmware switch number selection, the machine returns to the initial state the two digits firmware switch number selection, the machine returns to the initial state
of maintenance mode of maintenance mode automatically. automatically.
4-11 4-11
on to di o disp spla lay "M y "MAI AINTE NTENA NANC
he LCD. CD.
on to di o disp spla lay th y the wo e worke rker sw r swit itch n
pears on the LC s on the LCD. D.
n to mov ove th e the cu e curs rsor t or to th o the de
he [ [ ] o ] or [ r [ ] but utto ton. n. ] b
s completed, pres ed, press the [OK] bu s the [OK] button. The ne
d the LCD returns to the ready state for worker switch
leted, press the [S ss the [Stop/Exi
state of maintenance mode, press the
t of the number, if there is no entry for one minute or longer on , if there is no entry for one minute or longer on
NCE 10 E 10" on " on th the LC e LCD an D and pr d pres
ch num umbe ber th r that y at you w ou wan ant to s
e desi sire red se d selec lecto tor r , an , and ch d chan
tton. The new select w selector settin
state for worker switch
top/Exit] button to retu t] button to return the rn the
mode, press the
Confidential Confidential
ess th s the e
t to set o et on n
ange t ge the he
or setting g