Brother DCP-1510 Service Manual page 25

3 3 . . E E
3 3 . . 1 1 E E r r r r o o r r C C o o d d e e s s
Errors in the shaded columns do not usually occur during normal use. The possible causes Errors in the shaded columns do not usually occur during normal use. The possible causes
are noise around the installation site, fluctuation of the power supply voltage, and failures in are noise around the installation site, fluctuation of the power supply voltage, and failures in
the software. the software.
codes codes
0100 0100
0201 0201
0202 0202
0203 0203
0204 0204
0205 0205
0206 0206
0207 0207
0208 0208
0209 0209
0300 0300
0305 0305
R R R R O O R I R IN N D D I I C C
Error Error
Problem Problem
- -
The speed of the main motor The speed of the main motor
does not stabilize within the does not stabilize within the
specified time. specified time.
- -
- -
- -
- -
- -
- -
- -
- -
Cannot detect the lock signal of Cannot detect the lock signal of
the polygon motor for the laser the polygon motor for the laser
unit (second time). unit (second time).
- -
A A T T I I O O N N S S
Refer Refer Error Error
to: to: codes codes
0401 0401
1-23 1-23 0402 0402
0405 0405
0501 0501
0502 0502
0503 0503
After the heat unit was heated After the heat unit was heated
0504 0504
0505 0505
0506 0506
0508 0508
1-23 1-23 050A 050A
050B 050B
1-10 1-10
Problem Problem
Cannot detect the synchronized Cannot detect the synchronized
signal of the polygon motor for signal of the polygon motor for
the laser unit. the laser unit.
- -
- -
The center thermistor of the The center thermistor of the
fuser unit has not reached the fuser unit has not reached the
specified temperature within the specified temperature within the
specified time. specified time.
The center thermistor has not The center thermistor has not
reached the specified reached the specified
temperature within the specified temperature within the specified
time after the fuser unit has time after the fuser unit has
reached to a certain temperature. reached to a certain temperature.
The center thermistor of the The center thermistor of the
fuser unit detected a fuser unit detected a
temperature higher than the temperature higher than the
specified value. specified value.
normally, the center thermistor of normally, the center thermistor of
the fuser unit detected a the fuser unit detected a
temperature lower than the temperature lower than the
specified value. specified value.
The center thermistor of the fuser The center thermistor of the fuser
unit detected a temperature rise unit detected a temperature rise
greater than the specified value greater than the specified value
within the specified time. within the specified time.
The center thermistor of the fuser The center thermistor of the fuser
unit detected a temperature fall unit detected a temperature fall
greater than the specified value greater than the specified value
within the specified time. within the specified time.
The side thermistor of the fuser The side thermistor of the fuser
unit did not reach to the specified unit did not reach to the specified
temperature when the heater temperature when the heater
was ON. was ON.
The hardware detected that the The hardware detected that the
center thermistor of the fuser unit center thermistor of the fuser unit
indicated a temperature error. indicated a temperature error.
When the temperature of the When the temperature of the
center thermistor of the fuser unit center thermistor of the fuser unit
is lower than the idle temperature, is lower than the idle temperature,
the side thermistor of the fuser the side thermistor of the fuser
unit detected a temperature unit detected a temperature
higher than the specified value. higher than the specified value.
Refer Refer
to: to:
1-23 1-23
1-24 1-24
1-24 1-24
1-24 1-24
1-24 1-24
1-24 1-24
1-24 1-24
1-25 1-25
1-25 1-25
1-25 1-25
Confidential Confidential