Table of Contents
Advertisement
Available languages
Available languages
a) Use the
buttons to go to the set-up menu
press the
button;
b) Select the password
"7"
with the
button;
c) Scroll with the buttons
; will flash
;
[30]
"--0"
d) Press the
button and enter the value
button;
e) Press the button
to confirm;
f) The configuration currently in use will be displayed;
g) To modify, press the
new configuration with the
h) Press the button
to confirm the settings.
After changing the configuration, a communication error
message may appear for a few seconds� Ignore it and switch
the stove off with the safety switch on the back, wait a
few seconds and switch it on again�
9�5 CONFIGURATION SELECTION
9�5�1 Configuration 1 (default)
Set this configuration to switch the stove on and off
manually or with a program.
The stove will modulate the power according to the
ambient temperature read by the probe on board.
It is possible to set the "Eco-mode" function so that the
stove switches off or on again according to the set room
temperature.
In this configuration it is also possible to set the anti-
freeze function, which will work with the timer enabled.
9�5�2 Configuration 2
Set this configuration when the stove is controlled by a
room thermostat (or chronothermostat).
In this configuration the stove switches off when the
room thermostat is satisfied.
The antifreeze function cannot be set in this configuration
either.
The connector terminals are located on the back of the
stove.
The first time, following the installation of the
chronothermostat, the stove must be switched on
manually while the chronothermostat is in the "called"
state� This operation is also necessary in the event of a
power failure or if the stove is switched off manually�
To avoid overlapping operating time bands, we recommend
disabling the stove timer (set to OFF)�
9�6 SETTING THE DISPLAY BRIGHTNESS
Display brightness when in standby mode can be set.
a) Use the arrow buttons
and then press
;
b) Use the
button to select the password
to confirm;
c) Use the
button to scroll to and select submenu
then press
to confirm;
d) Set the desired brightness (
buttons and then press
with the
button and confirm
and select the submenu
with the
"54"
button and enter the value of the
buttons;
to go to the setup menu
and then press
"7"
[11]
,
-
) using the
OFF
1
5
to confirm.
9�7 SETTING THE DISPLAY MODE
and
The data shown on the display when this is in standby
mode can be set.
a) Use the arrow buttons
then press
to confirm;
b) Use the
button to select the password
to confirm;
c) Use the
button to scroll to and select submenu
then press
to confirm;
d) Set one of the following values using the
• The display remains on the last operation set by
OFF
the user;
• All operating parameters are displayed cyclically;
1
• The room probe temperature is shown;
2
• The current time is shown;
3
e) Press the button
9�8 SETTING THE VOLUME
The volume of the buzzer can be set based on requirements:
a) Use the arrow buttons
and then press
b) Use the
button to select the password
press
to confirm;
c) Use the
button to scroll to and select submenu
then press
to confirm;
d) Set the desired volume (
and then press
9�9 IMPROVING THE COMBUSTION
A good combustion depends on several factors (type of
installation, operation and maintenance conditions, type
of pellet etc ..)
If at the end of combustion in the fire pot are many waste,
it is advisable to change the combustion configurations
(increasing the value) to find the most satisfactory
solution.
a) Use the arrow buttons
and then press
b) Use the
button to select the password
press
to confirm;
c) Use the
button to scroll to and select submenu
then press
to confirm;
d) Set one of the following values using the
"2", "3"
e) Press the button
and
ENGLISH
to go to the setup menu
and then press
"7"
and
to confirm the settings.
to go to the setup menu
to confirm;
"7"
,
-
) using the
OFF
1
5
to confirm.
to go to the setup menu
to confirm;
"7"
to confirm the settings.
and
and
[12]
buttons:
and then
and
[13]
buttons
and then
and
[14]
buttons: "1",
23
Advertisement
Chapters
Table of Contents
