Mar31/82 - Raytheon BEECH BARON 58P Maintenance Manual

BEECHCRAFT
BARON 58P AND BARON 58TC
MAINTENANCE MANUAL
FULLY EXTrNDED
RETAINING RING
SPRING GUIDE
3/4" (APPROX)- APPLY GREASE
(LIOHTLY HERE ONLY)
ABSOLUTELY NO GREASE
SPRING GUIDE
TUBE
IFI THIS AREA
MAIN ASSY
COUNTERBALANCE
SPRING
60-3(4-1
ROTOR LOCK
FIGURE 202
e.
Remove the screws, washers and nuts wnlcn
glareshield.
secure
the support
assemblies
to the seat back frame
b. Pull up
Sentry
on
the front of the
glareshield
and
assembly
and
remove
the support
assemblies,
disconnect the wiring
for the compass and the floodlights
f.
Temporarily
install
an
appropriate size and length
(TJ-3 thru TJ-168,
TK-1 thru TK-84)
or
annunciator panel
screw,
washer and
nut in the
screw
hole in each support
lights (TJ-169
and after, TK-85 and
after)
at
the connectors.
assembly
to
hold the assembly together.
Mark and line drill
c.
Pull the glareshield
away from the
slide-on
a
.156/.160-inch diameter hole through
the complete
fasteners located in three
places
at the base
of the
support
assembly
as
shown in the illustration.
windshield.
g.
Remove and discard the existing
roll pin from the d.
Disconnect the RH
and LH
glareshield air
upper hole
in the
support
assembly. Line drill
or ream
this
conditioning
ducts from the main ducts
at
the
clamps.
hole
to
.193/.200-inch diameter. (See Figure 203).
e.
Disconnect the defroster duct from the main
h. Remove the
screw,
washer and
nut
which
was
defroster duct tube at
the clamp.
temporarily
installed
in step
"f".
f. Remove the
glareshield from the
airplane.
i.
Drill
or ream
the upper hole in the filler plates only
to
.256/.267-inch diameter.
(See Figure 203).
i.
Deburr all holes and
reassemble
the support
assembly with
a new
MS171559 roll
pin in the center hale.
GLARESHIELD INSTALLA TION
k.
Reinstall the
support
assembly
in the seat
back
frame
assembly with
one
each existing
screw,
washer and
a.
Place the glareshield in the airplane and
nut
and
one
each
new
MS27039-1-21
screw,
AN960D10 reconnect the electrical wiring
for the compass and the flood
washer and MS21083N3
nut.
lights (TJ-3 thru TJ-168, TK-1 thru TK-84)
or
annunciator
I.
Reassemble the seat back
locking mechanism
to
panel lights (TJ-169 and after,
TK85 and after.)
the support
assemblies.
b. Connect the defroster duct
at
the glareshield
to
m.
Reinstall the plastic shell
on
the
seat
back and
the main defroster duct tube and
secure
with the duct
reinstall the
seat back assembly
on
the seat.
clamp. Connect the RH and LH air conditioning ducts
to
the
n.
Reinstall the third and fourth
seats
in the
airplane.
main air conditioning ducts and
secure
them with clamps.
c.
Place the glareshield down in
position making
sure
that it fits properly
over
the fasteners
at
the base of the
GLARESHIELD REMOVAL windshield.
d. Secure the glareshield
on
both sides with the
a.
Remove the
attaching
screws on
both sides of
the
attach
screws.
25-00-00
Page
203
A16
Mar31/82