Surfaces Susceptible To Mud And Spray; Rubber Seals; Battery Box And Lid; Paint Free Areas - Raytheon BEECH BARON 58P Maintenance Manual

BEECHCRAFT
BARON
58P AND BARON 58tC
MAINTENANCE MANUAL
Apply
an
elastomeric rain erosion coating to the base of the
a.
Engine
controls.
radome and extending four
to
six inches
upward and
b. Flight control cables and chains.
feathering
out. Spray with only
one
coat
of primer
and
c.
Control
pedals.
maximum
of
two
topcoats
of non-metallic
pigmented paint.
d. Exhaust manifolds
and exhaust stacks.
e.
Firewalls and wrought
aluminum surfaces forward
of the
firewall, with the
following
exception:
SURFACES SUSCEPTIBLE
TO MUD AND SPRAY
i. Aluminum
parts attached directly
to the
firewall shall be primed and painted in detail.
Apply
one
coat of white
epoxy
paint
to
the following
areas:
f. Aluminum flexible
conduit.
g.
All tubing
except unplated steel, which shall
a.
Main and
nose
landing
gear
wheel wells,
receive
two
coats of primer
on
the exterior, and
except
as
b. Interior surface of landing
gear doors.
noted for the
interior of the engine
compartment,
and
c.
Main and
nose
landing gear assemblies,
interiors where the color scheme
must be maintained.
h. Interiorof all fluid lines.
i. Chromium plated
portions of the
landing
gear
RUBBER SEALS
piston tubes.
j. Rubber
and rubber like surfaces.
Apply
one
coat
of
a
thoroughly dissolved solution of
one
k. Electrical wiring, unless otherwise
noted
as a
part Oakite No. 6 and
two parts
water to all rubber surfaces
specific
requirement.
that
are
to
come
into contact with metal
or
other rubber
i.
Glide
path antenna (if installed).
surfaces. Apply
a
thin coat of Dow Coming
No. 7 after the
m.
Pitot
mast
and static button.
finish
topcoat is
dry,
n.
Cabin
door sill and upper latch.
ENCLOSED AREAS SUB3ECT TO HIGH HUMIDITY
The
following items
are
painted with
Insignia Red, Ameron
94-509 Baking Enamel
on
all Baron 55P aircraft.
Steel, aluminum
or
magnesium
parts
and assemblies which
are
enclosed
and subject to high
humidity
should be
a.
Fuel selector handle.
protected
against
corrosion
by coating with either
epoxy
b.
Landing
gear emergency
operation handle.
primer,
Mll-C-16173
corrosion
preventative compound, light
c.
Control
lock assembly
except
the portion
of the
grease or
heavy
oil,
pin which extends
into
the control column.
d. Lock assembly, rudder pedal safety
and chain.
BATTERY BOX AND LID
Apply
a
minimum of three
coats
of
vinyl
paint
to
the interior
The
following
items
are
painted with Instrument Black,
ANA
of the
battery box and lid in the following
manner:
color No. 51.
a.
One
coat
of EX2016G wash primer.
a.
Console
cover.
b.
One
coat
of intermediate vinyl paint.
b.
Elevator
tab drum shield.
c.
One
coat
of finish vinyl paint,
c.
Upper
and lower center console.
d. Engine control
levers.
e.
Nose gear indicator bezel.
NOTE
f. Instrument faces and bezels.
g.
Radio.
To insure complete coverage, each
coat must
h. Bendix
ignition switch handles.
be of
a
different color
and
must
completely hide
i. Instrument
panel cutout
covers.
the preceding
coat.
The final
coat
shall
be
gray
in color.
Apply Aluminum Lacquer
to all sound deadener material
above
the baggage
compartment
floor in the forward
PAINT FREE AREAS
baggage
compartment.
The following
areas
shall be kept
free from
paint:
"END"
20´•00-00
Page
206
Oct 26/79