Roland R1000 Series Manual page 97

B0046991 / Rev. 1.6
The fault message "30" means teach-in fault. This means that a teach-in has been attempted with a
sheet which is 25% thinner or 34% thicker than the nominal value of the selected measuring
program. This could mean that the selected measuring program is not intended for the sheet
presently in front of the sensor or that an incorrect sheet is being used for the teach-in process.
The described data formats above must be followed exactly for data transmission otherwise the
R1000 will issue an fault message.
All available fault messages and their meaning are described in chapter "9. Fault messages".
For downloading, the R1000 sends the data of all measuring programs complete as one block.
The format of the table below applies. If the data is requested for the currently selected program or
one specific program then the R1000 sends the data in the format described below but for one
program only.
Program no.
Sensor no.
Nominal value
Lower limit %
Upper limit %
Teach factor S1
Teach factor S2
Teach factor S3
Teach factor S4
Program no.
Sensor no.
Nominal value
Lower limit %
Upper limit %
Teach factor S1
Teach factor S2
Teach factor S3
Teach factor S4
Program no.
Program no.
Sensor no.
Nominal value
Lower limit %
Upper limit %
Teach factor S1
Teach factor S2
Teach factor S3
Teach factor S4
Pos : 51 /Komponenten allgemei n/Leers eite @ 0\mod_1165223317234_501.doc @ 2343 @ @ 1
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone +49 (0)7236-9392-0 · Fax +49 (0)7236-9392-33
Double Sheet Detector R1000 series E20
Byte Byte Byte Byte Byte
0 1 2 3 4
STX - P + 0
STX - J + 0
STX - N + X
STX - u + 0
STX - o + 0
STX - t + 1
STX - Q + 1
STX - G + 1
STX - E + 1
STX - P + 0
STX - J + 0
STX - N + X
STX - u + 0
STX - o + 0
STX - t + 1
STX - Q + 1
STX - G + 1
STX - E + 1
03 - 254
STX - P + 0
STX - J + 0
STX - N + X
STX - u + 0
STX - o + 0
STX - t + 1
STX - Q + 1
STX - G + 1
STX - E + 1
Manual
Byte Byte Byte Byte Byte
5 6 7 8 9
0 0
0 0 1
0 0 0 ZZ ZE
• X X X X
0 0 0 ZZ ZE
0 0 ZH ZZ ZE
• 0 0 0 0
• 0 0 0 0
• 0 0 0 0
• 0 0 0 0
0 0
0 0 2
0 0 0 ZZ ZE
• X X X X
0 0 0 ZZ ZE
0 0 ZH ZZ ZE
• 0 0 0 0
• 0 0 0 0
• 0 0 0 0
• 0 0 0 0
0 0
2 5 5
0 0 0 ZZ ZE
• X X X X
0 0 0 ZZ ZE
0 0 ZH ZZ ZE
• 0 0 0 0
• 0 0 0 0
• 0 0 0 0
• 0 0 0 0
Communication with the PLC
Byte Byte Byte Byte Byte
10 11 12 13 14
- - QH QZ QE
- - QH QZ QE
Dimension QH QZ QE
% - QH QZ QE
% - QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
- - QH QZ QE
- - QH QZ QE
Dimension QH QZ QE
% - QH QZ QE
% - QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
- - QH QZ QE
- - QH QZ QE
Dimension QH QZ QE
% - QH QZ QE
% - QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
0 0 QH QZ QE
Byte
15
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
ETX
97