Omron NJ Series Troubleshooting Manual page 24

Related Manuals
Manual name Cat. No.
NJ-series Troubleshoot- W503
ing Manual
CJ-series Special Unit W490
Manuals for NJ-series W498
CPU Unit W491
Z317
W492
W494
W497
W495
W493
Sysmac Studio Version 1 W504
Operation Manual
CX-Integrator W464
CS/CJ/CP/NSJ-series
Network Configuration
Tool Operation Manual
CX-Designer User's V099
Manual
CX-Protocol Operation W344
Manual
GX-series EtherCAT W488
Slave Unit User's Manual
MX2/RX Series Inverter I574
EtherCAT Communica-
tion Unit User's Manual
G5-series AC Servomo- I576
tors/Servo Drives with
Built-in EtherCAT Com-
munications User's Man-
ual
G5-series Linear I577
Motors/Drives with Built-
in EtherCAT Communica-
tions Linear Motor Type
User's Manual
22
Model numbers Application
NJ501-@@@@ Learning about the
NJ301-@@@@ errors that may be
detected in an NJ-series
Controller.
CJ1W-@@@@ Learning how to use CJ-
series Units with an NJ-
series CPU Unit.
SYSMAC- Learning about the
SE2@@@ operating procedures
and functions of the
Sysmac Studio.
Learning how to config-
ure networks (data links,
routing tables, Commu-
nications Unit settings,
etc.).
Learning to create
screen data for NS-
series Programmable
Terminals.
Creating data transfer
protocols for general-
purpose devices con-
nected to CJ-series
Serial Communications
Units.
GX-ID@@@@
Leaning how to connect
GX-OD@@@@ GX-series EtherCAT
GX-OC@@@@ Slave Units.
GX-MD@@@@
GX-AD@@@@
GX-DA@@@@
GX-EC@@@@
XWT-ID@@
XWT-OD@@
3G3AX-MX2- Leaning how to connect
ECT a 3G3AX-MX2-ECT or
3G3AX-RX-ECT 3G3AX-RX-ECT Ether-
CAT Communications
Unit for MX2/RX-series
Inverters.
R88D-KN@-ECT Leaning how to connect
R88M-K@ G5-series AC Servomo-
tors/Servo Drives with
Built-in EtherCAT Com-
munications.
R88D-KN@-ECT- Leaning how to connect
L G5-series Linear
R88L-EC-@W-@ Motors/Drives with Built-
R88L-EC-@M-@ in EtherCAT Communi-
cations Linear Motor
Type.
Description
Concepts on managing errors that may be detected
in an NJ-series Controller and information on individ-
ual errors are described.
Use this manual together with the NJ-series CPU
Unit Hardware User's Manual (Cat. No. W500) and
NJ-series CPU Unit Software User's Manual (Cat.
No. W501).
The methods and precautions for using CJ-series
Units with an NJ501 CPU Unit are described, includ-
ing access methods and programming interfaces.
Manuals are available for the following Units.
Analog I/O Units, Insulated-type Analog I/O Units,
Temperature Control Units, ID Sensor Units, High-
speed Counter Units, Serial Communications Units,
DeviceNet Units, EtherNet/IP Units, and CompoNet
Master Units.
Use these manuals together with the NJ-series CPU
Unit Hardware User's Manual (Cat. No. W500) and
NJ-series CPU Unit Software User's Manual (Cat.
No. W501).
Describes the operating procedures of the Sysmac
Studio.
Describes operating procedures for the CX-Integra-
tor.
Describes operating procedures for the CX-
Designer.
Describes operating procedures for the CX-Protocol.
Provides the specifications of and describes applica-
tion methods for GX-series EtherCAT Slave Units.
Describes the following information for the 3G3AX-
MX2-ECT and 3G3AX-RX-ECT EtherCAT Communi-
cations Unit for MX2/RX-series Inverters: installation,
parameter settings required for operation, trouble-
shooting, and inspection methods.
Describes the following information for the G5-series
AC Servomotors/Servo Drives with EtherCAT Com-
munications: installation, wiring methods, parameter
settings required for operation, troubleshooting, and
inspection methods.
Describes the following information for the G5-series
Linear Motors/Drives with EtherCAT Communica-
tions Linear Motor Type: installation, wiring methods,
parameter settings required for operation, trouble-
shooting, and inspection methods.
NJ-series Troubleshooting Manual (W503)