Teledyne D series Installation And Operation Manual page 148

D Series Syringe Pumps
Section 7 Modbus Configuration
Table 7-5 Coils (Continued)
Register Address
00078 77
00079 78
00080 79
00081 80
00082 81
00083 82
00084 83
00085 84
00086 85
00087 86
00088 87
00089 88
00090 89
00091 90
00092 91
00093 92
00094 93
00095 94
00096 95
00097 96
00098 97
00099 98
00100 99
00101 100
00102 101
00103 102
00104 103
00105 103
00106 105
00107 106
00108 107
00109 108
00110 109
00111 110
00112 111
00113 112
00114 113
7-6
Type Size Description
R/W 1 BIT 0: DIGITAL OUTPUT BIT 8 HIGH 1: DIGITAL OUTPUT BIT 8 LOW
0: Disable Dispense Mode A 1: Enable Dispense Mode A Only configure if in Constant Flow
R/W 1 BIT
Mode
0: Disable Dispense Mode B 1: Enable Dispense Mode B Only configure if in Constant Flow
R/W 1 BIT
Mode
0: Disable Dispense Mode C 1: Enable Dispense Mode C Only configure if in Constant Flow
R/W 1 BIT
Mode
0: Disable Dispense Mode D 1: Enable Dispense Mode D Only configure if in Constant Flow
R/W 1 BIT
Mode
R/W 1 BIT 1: Reset total volume delivered by multi-pump pair AB
R/W 1 BIT 1: Reset total volume delivered by multi-pump pair CD
R/W 1 BIT 1: Pressure Units =ATM
R/W 1 BIT 1: Pressure Units = BAR
R/W 1 BIT 1: Pressure Units = kPa
R/W 1 BIT 1: Pressure Units = PSI
R/W 1 BIT 1: Flow Units = ml/min
R/W 1 BIT 1: Flow Units = ml/hr
R/W 1 BIT 1: Flow Units = ul/min
R/W 1 BIT 1: Flow Units = ul/hr
R/W 1 BIT 0: Overpressure Alarm OFF 1: Overpressure Alarm ON
R/W 1 BIT 0: Overpressure Display OFF 1: Overpressure Display ON
R/W 1 BIT 0: Overpressure Shutdown OFF 1: Overpressure Shutdown ON
R/W 1 BIT 0: Underpressure Alarm OFF 1: Underpressure Alarm ON
R/W 1 BIT 0: Underpressure Display OFF 1: Underpressure Display ON
R/W 1 BIT 0: Underpressure Shutdown OFF 1: Underpressure Shutdown ON
R/W 1 BIT 0: Overflow Alarm OFF 1: Overflow Alarm ON
R/W 1 BIT 0: Overflow Display OFF 1: Overflow Display ON
R/W 1 BIT 0: Overflow Shutdown OFF 1: Overflow Display ON
R/W 1 BIT 0: Underflow Alarm OFF 1: Underflow Alarm ON
R/W 1 BIT 0: Underflow Display OFF 1: Underflow Display ON
R/W 1 BIT 0: Underflow Shutdown OFF 1: Underflow Shutdown ON
R/W 1 BIT 0: Poor Fill Alarm A OFF 1: Poor Fill Alarm A ON
R/W 1 BIT 0: Poor Fill Alarm B OFF 1: Poor Fill Alarm B ON
R/W 1 BIT 0: Poor Fill Alarm C OFF 1: Poor Fill Alarm C ON
R/W 1 BIT 0: Poor Fill Alarm D OFF 1: Poor Fill Alarm D ON
R/W 1 BIT 1: Stop all motor and reset flow rate and pressure set-points to default.
R 1 BIT 0: Transducer of Pump A not connected 1: Transducer of Pump A connected
R 1 BIT 0: Pump A not at upper flag limit 1: Pump A at upper Flag Limit (Empty)
R 1 BIT 0: Pump A not at lower flag limit 1: Pump A at lower flag limit (Full)
R 1 BIT 1: Pump A is overpressure
R 1 BIT 1: Pump A is underpressure