Mitsubishi Electric FR-A820-00046 Instruction Manual page 367

Parameters
Positioning by a point table (Pr. 4 to Pr. 6, Pr. 24 to Pr. 27, Pr. 232 to Pr. 239, Pr. 465 to Pr. 494,
Pr. 1222 to Pr. 1281)
● Create a the point table by setting the following parameters.
Point
table
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Tab. 5-54:
Position data settings
● Set the position feed length to Pr. 465 to Pr. 494.
● The feed length set to each point table is selected by multi-speed terminals (RH, RM, RL and REX).
● Under vector control with encoder, set the value calculated with the following formula as the
position feed length: (encoder resolution × number of rotations × 4).
● For example, to stop the motor after 100 times of rotations using SF-V5RU, the value will be
calculated with 2048 (pulse/r) × 100 (rotations per minute) × 4 (multiplier) = 819200 (feed length)
To set 819200 as the first feed length, separate the number in to the upper and lower 4 digits as
shown below:
● Pr. 466 (upper) = 81 (decimal), Pr. 465 (lower) = 9200 (decimal)
● The position feed length of PM sensorless vector control is fixed at 4096 for each motor rotation.
Acceleration/deceleration time
● Set the acceleration/deceleration time for parameters corresponding to each point table.
● The frequency that will be the basis of acceleration/deceleration time is Pr. 20 "Acceleration/
deceleration reference frequency." However, 1 Hz/s is the minimum acceleration/deceleration rate
(acceleration/deceleration frequency divided by acceleration/deceleration time). If the accelera-
tion/deceleration rate is smaller than 1, the motor runs at 1 Hz/s or in the deceleration time.
● The maximum acceleration/deceleration time is limited at 360 s.
● During position control, acceleration/deceleration pattern is always the liner acceleration/decel-
eration, and the Pr. 29 "Acceleration/deceleration pattern selection" setting is ignored.
FR-A800
Position control under vector control and PM sensorless vector control
Position data
Maxi-
[command side]
mum eration
speed
Upper Lower
Pr. 466 Pr. 465 Pr. 4 Pr. 1222 Pr. 1223 Pr. 1224 Pr. 1225
Pr. 468 Pr. 467 Pr. 5 Pr. 1226 Pr. 1227 Pr. 1228 Pr. 1229
Pr. 470 Pr. 469 Pr. 6 Pr. 1230 Pr. 1231 Pr. 1232 Pr. 1233
Pr. 472 Pr. 471 Pr. 24 Pr. 1234 Pr. 1235 Pr. 1236 Pr. 1237
Pr. 474 Pr. 473 Pr. 25 Pr. 1238 Pr. 1239 Pr. 1240 Pr. 1241
Pr. 476 Pr. 475 Pr. 26 Pr. 1242 Pr. 1243 Pr. 1244 Pr. 1245
Pr. 478 Pr. 477 Pr. 27 Pr. 1246 Pr. 1247 Pr. 1248 Pr. 1249
Pr. 480 Pr. 479 Pr. 232 Pr. 1250 Pr. 1251 Pr. 1252 Pr. 1253
Pr. 482 Pr. 481 Pr. 233 Pr. 1254 Pr. 1255 Pr. 1256 Pr. 1257
Pr. 484 Pr. 483 Pr. 234 Pr. 1258 Pr. 1259 Pr. 1260 Pr. 1261
Pr. 486 Pr. 485 Pr. 235 Pr. 1262 Pr. 1263 Pr. 1264 Pr. 1265
Pr. 488 Pr. 487 Pr. 236 Pr. 1266 Pr. 1267 Pr. 1268 Pr. 1269
Pr. 490 Pr. 489 Pr. 237 Pr. 1270 Pr. 1271 Pr. 1272 Pr. 1273
Pr. 492 Pr. 491 Pr. 238 Pr. 1274 Pr. 1275 Pr. 1276 Pr. 1277
Pr. 494 Pr. 493 Pr. 239 Pr. 1278 Pr. 1279 Pr. 1280 Pr. 1281
Creating a point table
Accel- Decel- Auxilia-
Dwell
eration ry func-
time
time time
Point table selection signal
tion
REX RH
OFF ON
OFF OFF
OFF OFF
OFF OFF
OFF ON
OFF ON
OFF ON
ON OFF
ON OFF
ON OFF
ON OFF
ON ON
ON ON
ON ON
ON ON
RM RL
OFF OFF
ON OFF
OFF ON
ON ON
OFF ON
ON OFF
ON ON
OFF OFF
OFF ON
ON OFF
ON ON
OFF OFF
OFF ON
ON OFF
ON ON
5 - 165