Mitsubishi Q64AD-GH User Manual page 8

3.4.5 Averaging process specification (buffer memory address 9: Un\G9)............................................. 3-38
3.4.6 A/D conversion completed flag (buffer memory address 10: Un\G10) .......................................... 3-39
3.4.7 CH digital output value (16bit) (buffer memory addresses 11 to 14: Un\G11 to Un\G14).......... 3-39
3.4.8 Write data error codes (buffer memory address 19: Un\G19) ........................................................ 3-40
3.4.9 Setting range (buffer memory address 20: Un\G20)....................................................................... 3-40
3.4.10 Offset/gain setting mode (buffer memory addresses 22, 23: Un\G22, Un\G23) ......................... 3-41
3.4.11 CH maximum value/minimum value storage area (16bit)
(buffer memory addresses 30 to 37: Un\G30 to Un\G37) ............................................................ 3-41
3.4.12 Input signal error detection/warning output settings (buffer memory address 47: Un\G47)........ 3-42
3.4.13 Warning output flag (buffer memory address 48 :Un\G48) .......................................................... 3-42
3.4.14 Input signal error detection flag (buffer memory address 49: Un\G49)........................................ 3-43
3.4.15 CH digital output value (32bit) (buffer memory addresses 54 to 61: Un\G54 to Un\G61)........ 3-43
3.4.16 CH maximum value/minimum value storage area (32bit)
(buffer memory addresses 62 to 77: Un\G62 to Un\G77) ............................................................ 3-44
3.4.17 CH process alarm upper/lower limit value
(buffer memory addresses 86 to 117: Un\G86 to Un\G117) ........................................................ 3-44
3.4.18 CH rate alarm warning detection period
(buffer memory addresses 118 to 121: Un\G118 to Un\G121) .................................................... 3-45
3.4.19 CH rate alarm upper/lower limit value
(buffer memory addresses 122 to 137: Un\G122 to Un\G137) .................................................... 3-46
3.4.20 CH input signal error detection setting value
(buffer memory addresses 138 to 141: Un\G138 to Un\G141) .................................................... 3-47
3.4.21 Mode switching setting (buffer memory addresses 158, 159: Un\G158, Un\G159).................... 3-48
3.4.22 Pass data classification setting (buffer memory addresses 200: Un\G200) (Q64AD-GH only).. 3-48
3.4.23 Industrial shipment settings and user range settings offset/gain value
(buffer memory addresses 202 to 233: Un\G202 to Un\G233) .................................................... 3-49
4 SETUP AND PROCEDURES BEFORE OPERATION
4.1 Handling Precautions.............................................................................................................................. 4- 1
4.2 Setup and Procedures before Operation ............................................................................................... 4- 2
4.3 Part Identification Nomenclature ............................................................................................................ 4- 3
4.4 Wiring....................................................................................................................................................... 4- 5
4.4.1 Wiring precautions............................................................................................................................ 4- 5
4.4.2 External wiring .................................................................................................................................. 4- 6
4.5 Switch Setting for Intelligent Function Module ....................................................................................... 4- 8
4.6 Offset/Gain Settings ................................................................................................................................ 4-10
4.6.1 Offset/Gain Settings (Q64AD-GH)................................................................................................... 4-10
4.6.2 Offset/Gain Settings (Q62AD-DGH)................................................................................................ 4-14
4.6.3 A/D conversion value storage during offset/gain setting................................................................. 4-17
5 UTILITY PACKAGE (GX Configurator-AD)
5.1 Utility Package Functions........................................................................................................................ 5- 1
5.2 Installing and Uninstalling the Utility Package........................................................................................ 5- 2
5.2.1 User precautions .............................................................................................................................. 5- 2
5.2.2 Operating environment..................................................................................................................... 5- 4
A - 6
4- 1 to 4-17
5- 1 to 5-31
A - 6