Mitsubishi Electric MELSEC FX3U Programming Manual page 882

FX /FX /FX Series Programmable Controllers
3G 3U 3UC
Programming Manual - Basic & Applied Instruction Edition
Number and name
High Speed Counter Comparison, High Speed Table, and Positioning [Positioning is supported in FX
M 8130 HSZ (FNC 55)instruction: Table comparison mode
HSZ (FNC 55)instruction:
[M]8131
Table comparison mode completion flag
HSZ (FNC 55) and PLSY (FNC 57) instructions:
M 8132
Speed pattern mode
HSZ (FNC 55) and PLSY (FNC 57) instructions:
[M]8133
Speed pattern mode completion flag
[M]8134
[M]8135
Not used
[M]8136
[M]8137
HSCT (FNC280) instruction:
[M]8138
Instruction execution complete flag
HSCS(FNC 53), HSCR(FNC 54), HSZ(FNC 55),
HSCT(FNC280) instructions:
[M]8139
High
executing
ZRN (FNC156) instruction:
M 8140
CLR signal output function enable
[M]8141
[M]8142
Not used
[M]8143
[M]8144
M 8145 [Y000] Pulse output stop command
M 8146 [Y001] Pulse output stop command
[M]8147 [Y000] Pulse output monitor (BUSY/READY)
[M]8148 [Y001] Pulse output monitor (BUSY/READY)
[M]8149 Not used
Inverter Communication Function (Refer to Data Communication Edition for details.)
[M]8150 Not used
*1
Inverter communication in execution [ch1]
[M]8151
*1
Inverter communication error [ch1]
[M]8152
*1
Inverter communication error latch [ch1]
[M]8153
*1
IVBWR (FNC274) instruction error [ch1]
[M]8154
[M]8154 Defined per use of EXTR (FNC180)
[M]8155 EXTR (FNC180) is using communicating port
*1
Inverter communication in execution [ch2]
[M]8156
Communication error or parameter error in EXTR
[M]8156
(FNC180) instruction
Inverter communication error [ch2]
*1
[M]8157
Communication
instruction is latched.
*1
Inverter communication error latch [ch2]
[M]8158
*1
IVBWR (FNC274) instruction error [ch2]
[M]8159
*1. Cleared when PLC switches from STOP to RUN.
*2. Available in Ver. 3.00 or later.
*3. Available in Ver. 1.10 or later.
880
Operation and function
speed counter comparison
error in EXTR
37 Operation of Special Devices (M8000 -, D8000 -)
37.1 Special Device List (M8000 -, D8000 -)
FX FX FX
3G 3U 3UC
–
–
–
–
– – –
– – –
– – –
– – –
–
–
instruction
– – –
– – –
– – –
– – –
– – –
– –
– –
– –
– –
– – –
– – –
*3
*3
*3
–
– – –
– – –
*3
– –
–
*3
(FNC180)
– – –
*3
–
Applicable model
Correspond
-ing special FX FX FX
1S 1N 2N
device
, FX , FX , and FX
3G 1S 1N
– –
D8130
– –
– –
D8131
to
D8134
– –
– – – –
– – – –
– – – –
– – – –
D8138 – – –
D8139 – – –
– –
– – – –
– – – –
– – – –
– – – –
– –
– –
– –
– –
– – – –
– – – –
D8151 – – –
D8152 – – –
D8153 – – –
D8154 – – –
*2
– – –
*2
D8155 – –
D8156
*2
D8156 – –
D8157
*2
D8157 – –
D8158 – – –
D8159 – – –
FX FX
1NC 2NC
PLCs.]
1NC
–
–
–
–
– –
– –
– –
– –
– –
– –
–
– –
– –
– –
– –
–
–
–
–
– –
– –
– –
– –
– –
– –
*2
–
*2
–
*2
–
*2
–
– –
– –