Siemens SINUMERIK 840D sl Operating Manual page 12
Hide thumbs
Also See for SINUMERIK 840D sl:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
Table of contents
8.1.5.1
Function..................................................................................................................................... 281
8.1.6
Boring (CYCLE86) .................................................................................................................... 284
8.1.6.1
Function..................................................................................................................................... 284
8.1.7
Tapping (CYCLE84, 840).......................................................................................................... 286
8.1.7.1
Function..................................................................................................................................... 286
8.1.8
Drill and thread milling (CYCLE78) ........................................................................................... 291
8.1.8.1
Function..................................................................................................................................... 291
8.1.9
Positioning and position patterns .............................................................................................. 295
8.1.10
Arbitrary positions (CYCLE802)................................................................................................ 297
8.1.11
Position pattern Line (HOLES1), Grid or Frame (CYCLE801).................................................. 300
8.1.12
Circle position pattern (HOLES2).............................................................................................. 302
8.1.13
Displaying and hiding positions................................................................................................. 304
8.1.14
Repeating positions................................................................................................................... 305
8.2
Milling ........................................................................................................................................ 307
8.2.1
Face milling (CYCLE61)............................................................................................................ 307
8.2.1.1
Function..................................................................................................................................... 307
8.2.2
Rectangular pocket (POCKET3)............................................................................................... 310
8.2.3
Circular pocket (POCKET4) ...................................................................................................... 313
8.2.4
Rectangular spigot (CYCLE76)................................................................................................. 318
8.2.5
Circular spigot (CYCLE77)........................................................................................................ 321
8.2.5.1
Function..................................................................................................................................... 321
8.2.6
Multi-edge (CYCLE79) .............................................................................................................. 323
8.2.6.1
Function..................................................................................................................................... 323
8.2.7
Longitudinal groove (SLOT1) .................................................................................................... 326
8.2.8
Circumferential groove (SLOT2) ............................................................................................... 329
8.2.9
Open groove (CYCLE899) ........................................................................................................ 332
8.2.10
Long hole (LONGHOLE) - only for G code programs............................................................... 339
8.2.11
Thread milling (CYCLE70) ........................................................................................................ 341
8.2.12
Engraving (CYCLE60)............................................................................................................... 344
8.3
Contour milling .......................................................................................................................... 351
8.3.1
General...................................................................................................................................... 351
8.3.2
Representation of the contour................................................................................................... 351
8.3.3
Creating a new contour ............................................................................................................. 353
8.3.4
Creating contour elements ........................................................................................................ 355
8.3.5
Changing the contour................................................................................................................ 360
8.3.6
Contour call (CYCLE62) - only for G code program ................................................................. 361
8.3.7
Path milling (CYCLE72) ............................................................................................................ 362
8.3.8
Contour pocket/contour spigot (CYCLE63/64).......................................................................... 366
8.3.9
Predrilling contour pocket (CYCLE64) ...................................................................................... 368
8.3.10
Milling contour pocket (CYCLE63)............................................................................................ 371
8.3.11
Residual material contour pocket (CYCLE63) .......................................................................... 373
8.3.12
Milling contour spigot (CYCLE63)............................................................................................. 375
8.3.13
Residual material contour spigot (CYCLE63) ........................................................................... 377
8.4
Turning - only for G code programs .......................................................................................... 380
8.4.1
General...................................................................................................................................... 380
8.4.2
Stock removal (CYCLE951) ...................................................................................................... 380
8.4.3
Groove (CYCLE930) ................................................................................................................. 383
8.4.4
Undercut form E and F (CYCLE940) ........................................................................................ 386
8.4.5
Thread undercut (CYCLE940) .................................................................................................. 388
8.4.6
Thread turning (CYCLE99) ....................................................................................................... 391
8.4.7
Thread chain (CYCLE98).......................................................................................................... 400
12
Operating Manual, 09/2011, 6FC5398-7CP40-2BA0
Milling
Advertisement
Table of Contents
