Standard Default Setting; Factory Default Setting - Toshiba TOSVERT VF-PS1 Instruction Manual

5.20

Standard default setting


• Function
This parameter is to set two or more parameters at a time for different commands. Using this parameter, all
parameters can be also return to their respective default settings by one operation, and save or set specific
parameters individually.
Title

Note 1: This parameter is used to change the settings of other parameters. Therefore,  is always displayed.
Note 2:  cannot be set during the inverter operating. Always stop the inverter first and then program.
5
Note 3: When parameter  is invoked, the value set previously is displayed on the left side of the parameter.
Note 4: If  is set to , the optional communication devices DEV002Z, PDP002Z, MTS001Z, APG001Z,
LIU006Z, BCN001Z, IPE001Z and CCL001Z cannot be used with the inverter. (The personal computer
communications software PCM001Z cannot be used, either.) Furthermore, the copy function of the LED
extended panel option (RKP002Z) does not work normally, so use only the parameter setting function and the
monitoring function.
Note 5: If the power is turned off while the parameter  is being set, an error () will occur when the power
is turned back on. If the error occurs, set  again.
[Programmed value]
50Hz default setting (=)
Setting  at  causes all the following parameters to be set for operation using a base frequency of 50Hz.
(This does not change the settings of any other parameters.)
• Upper limit frequency 
• Base frequency 2 
• Maximum frequency 
• Base frequency 1 
• RR/S4 input point 2 frequency 
• VI/II input point 2 frequency 
• RX input point 2 frequency 
• AI1 input point 2 frequency 
• AI2 input point 2 frequency 
• RP/high-speed pulse input point 2 frequency  : 50Hz
60Hz default setting (=)
Setting  at  causes all the following parameters to be set for operation using a base frequency of 60Hz.
(This does not change the settings of any other parameters.)
• Upper limit frequency 
• Base frequency 2 
• Maximum frequency 
• Base frequency 1 
• RR/S4 input point 2 frequency 
• VI/II input point 2 frequency 
• RX input point 2 frequency 
• AI1 input point 2 frequency 
• AI2 input point 2 frequency 
• RP/high-speed pulse input point 2 frequency  : 60Hz

: Factory default setting

Function
: –
:50Hz default setting
:60Hz default setting
:Factory default setting
:Trip clear
:Cumulative operation time cleared
Factory default
:Initialization of type information
setting
:Save user-defined parameters
:Reset of user-defined parameters
:Cumulative fan operation time record clear
:Acceleration/deceleration time setting 0.01 sec.~600.0 sec.
[Note 4]
:Acceleration/deceleration time setting 0.1 sec.~6000 sec.
Adjustment range
: 50Hz • Commercial power/inverter switching frequency  : 50Hz
: 50Hz • PID deviation upper limit 
: 50Hz • PID deviation lower limit 
: 50Hz • Process upper limit 
: 50Hz • PID output upper limit 
: 50Hz • Motor rated rotational speed :1400~1480min-1 (According to model)
: 50Hz • Point 2 frequency 
: 50Hz
: 50Hz
: 60Hz • Commercial power/inverter switching frequency  : 60Hz
: 60Hz • PID deviation upper limit 
: 60Hz • PID deviation lower limit 
: 60Hz • Process upper limit 
: 60Hz • PID output upper limit 
: 60Hz • Motor rated rotational speed :1680~1775min-1 (According to model)
: 60Hz • Point 2 frequency 
: 60Hz
: 60Hz
E-40
E6581386
Default setting

: 50Hz
: 50Hz
: 50Hz
: 50Hz
: 50Hz
: 60Hz
: 60Hz
: 60Hz
: 60Hz
: 60Hz