HP HSR6800 Configuration Manual page 343
Hide thumbs
Also See for HSR6800:
- Command reference manual (170 pages) ,
- Installation manual (146 pages) ,
- Configuration manual (95 pages)
Table of Contents
Advertisement
[ASBR-PE2-mpls] quit
[ASBR-PE2] mpls ldp
[ASBR-PE2-mpls-ldp] quit
# Configure interface Serial 2/1/1, and start IS-IS and enable MPLS and LDP on the interface.
[ASBR-PE2] interface serial 2/1/1
[ASBR-PE2-Serial2/1/1] ip address 9.1.1.1 255.0.0.0
[ASBR-PE2-Serial2/1/1] isis enable 1
[ASBR-PE2-Serial2/1/1] mpls
[ASBR-PE2-Serial2/1/1] mpls ldp
[ASBR-PE2-Serial2/1/1] quit
# Configure interface Loopback 0 and start IS-IS on it.
[ASBR-PE2] interface loopback 0
[ASBR-PE2-LoopBack0] ip address 4.4.4.9 32
[ASBR-PE2-LoopBack0] isis enable 1
[ASBR-PE2-LoopBack0] quit
# Configure interface Serial 2/1/2 and enable MPLS on it.
[ASBR-PE2] interface serial 2/1/2
[ASBR-PE2-Serial2/1/2] ip address 11.0.0.1 255.0.0.0
[ASBR-PE2-Serial2/1/2] mpls
[ASBR-PE2-Serial2/1/2] quit
# Create routing policies.
[ASBR-PE2] route-policy policy1 permit node 1
[ASBR-PE2-route-policy1] apply mpls-label
[ASBR-PE2-route-policy1] quit
[ASBR-PE2] route-policy policy2 permit node 1
[ASBR-PE2-route-policy2] if-match mpls-label
[ASBR-PE2-route-policy2] apply mpls-label
[ASBR-PE2-route-policy2] quit
# Start BGP on ASBR-PE 2 and redistribute routes from IS-IS process 1.
[ASBR-PE2] bgp 600
[ASBR-PE2-bgp] import-route isis 1
# Configure the capability to advertise labeled routes to IBGP peer 5.5.5.9 and to receive
labeled routes from the peer.
[ASBR-PE2-bgp] peer 5.5.5.9 as-number 600
[ASBR-PE2-bgp] peer 5.5.5.9 connect-interface loopback 0
[ASBR-PE2-bgp] peer 5.5.5.9 label-route-capability
# Use routing policy policy2 to filter routes advertised to IBGP peer 5.5.5.9.
[ASBR-PE2-bgp] peer 5.5.5.9 route-policy policy2 export
# Use routing policy policy1 to filter routes advertised to EBGP peer 11.0.0.2.
[ASBR-PE2-bgp] peer 11.0.0.2 as-number 100
[ASBR-PE2-bgp] peer 11.0.0.2 route-policy policy1 export
# Configure the capability to advertise labeled routes to EBGP peer 11.0.0.2 and to receive
labeled routes from the peer.
[ASBR-PE2-bgp] peer 11.0.0.2 label-route-capability
[ASBR-PE2-bgp] quit
4.
Configure PE 2:
# Start IS-IS on PE 2.
<PE2> system-view
335
Advertisement
Table of Contents
Troubleshooting
