Page 1: Installation Guide
HP HSR6800 Routers Installation Guide 5998-4040 Part number: 5998-4040 Document version: 6PW102-20140210...
Page 2 The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Page 3: Table Of Contents
Contents Preparing for installation ············································································································································· 1 Safety recommendations ·················································································································································· 1 Safety symbols ·························································································································································· 1 Electricity safety ························································································································································ 2 Laser safety ································································································································································ 2 Router moving ··························································································································································· 2 ESD prevention ························································································································································· 3 Examining the installation site ········································································································································· 4 ...
Page 4 Transceiver module overview ······························································································································· 28 Fiber cable overview ············································································································································· 29 Connecting a fiber cable ······································································································································ 30 Connecting an E1/T1 cable ········································································································································· 31 Overview ································································································································································ 31 Connecting an E1/T1 cable ································································································································ 32 Connecting a CE3/CT3 cable ····································································································································· 34 ...
Page 5 Displaying the fan operating status ····················································································································· 60 Displaying the power module operating status ·································································································· 61 Displaying the alarming thresholds of a card ············································································································· 61 Port configuration and management ···························································································································· 62 Configuring a combo interface ···························································································································· 62 ...
Page 6 Labeling cables····························································································································································· 125 Cable management guidelines ··································································································································· 126 Cable routing example ················································································································································ 128 Support and other resources ·································································································································· 129 Contacting HP ······························································································································································ 129 Subscription service ············································································································································ 129 Related information ······················································································································································ 129 Documents ···························································································································································· 129 ...
Page 7: Preparing For Installation
SAP-4EXP SAP-4EXP IMPORTANT: For regulatory identification purposes, every HSR6800 Router is assigned a regulatory model number(RMN). These regulatory numbers should not be confused with the marketing name HP HSR6800, or product codes. Safety recommendations Safety symbols When reading this document, note the following symbols:...
Page 8: Electricity Safety
Electricity safety Locate the emergency power-off switch in the room before installation. Shut the power off at once in • case accident occurs. Disconnect the power cord of the router if necessary. • Use an uninterrupted power supply (UPS). Do not work alone when the router has power. Do not touch any power plug when it is connected. •...
Page 9: Esd Prevention
If the router needs to be moved over a long distance, remove all field replacement units (FRUs), such • as HIMs/MIMs, put them separately in anti-static bags, and install the filler panels supplied with router. • If the router needs to be moved over a short distance, make sure all FRUs are securely seated in slots and the screws are fastened.
Page 10: Examining The Installation Site
Figure 1 Attaching an ESD wrist strap (1) ESD wrist strap (2) Lock (3) ESD plug CAUTION: Check the resistance of the ESD wrist strap for safety. The resistance reading should be in the range of 1 to 10 megohm (Mohm) between human body and the ground. Examining the installation site The routers can only be used indoors.
Page 11: Humidity
Table 2 Temperature requirements Item Temperature Operating temperature 0°C to 45°C (32°F to 113°F) Storage temperature –40°C to +70°C (–40°F to +158°F) Humidity Maintain appropriate humidity in your equipment room, as described in Table Lasting high relative humidity tends to cause poor insulation, electricity creepage, mechanical •...
Page 12: Cooling System
Table 6 Harmful gas limits in an equipment room Max. (mg/m 0.006 0.05 0.01 Cooling system Fan trays of the routers are hot swappable and support automatic fan speed adjustment. To ensure good ventilation, the following requirements must be met: Leave at least 10 cm (3.94 in) of clearance at the inlet and outlet air vents.
Page 13: Emi
Figure 3 Airflow through the HSR6808 chassis Electromagnetic interference (EMI) might be coupled from the source to the router through the following coupling mechanisms: Capacitive coupling • Inductive coupling • Radiative coupling • • Common impedance coupling Conductive coupling • To prevent EMI, take the following actions: Take measures against interference from the power grid.
Page 14: Lightning Protection
Lightning protection To protect the router from lightning better, do as follows: • Make sure the grounding cable of the chassis is well grounded. For how to connect the grounding cable, see "Grounding the router." Make sure the grounding terminal of the AC power receptacle is well grounded. •...
Page 15 Mounting brackets Cable management M6 cage nut for the HSR6808 bracket for the M6 screws (supplied Cable tie (supplied with the (supplied with the HSR6808 (supplied with the router) (user-supplied) router) router) with the router) ESD gloves (user-supplied)
Page 16: Installing The Router
Installing the router Installation flow Figure 4 Installation flow Start Unpacking the router Install a cable management bracket （only on HSR6808 router） Install the router to a 19-inch rack Ground the router Install a power module Install an MPU and a switching fabric module Install an LPU Install a HIM/MIM...
Page 17: Installing The Router In A 19-Inch Rack
Figure 5 Installing a cable management bracket Installing the router in a 19-inch rack The procedures for installing an HSR6800 router in a rack are similar. This section uses an HSR6802 router as an example. To install the router in a rack, you need mounting brackets and a rack shelf.
Page 18: Installing The Mounting Brackets To The Router
Figure 6 Marking the positions of cage nuts Insert one edge of a cage nut into the hole. Use a flat-blade screwdriver to compress the other edge of the cage nut, and then push the cage nut fully into the hole. Repeat steps 3 and 4 to install other cage nuts to all the marked positions on the rack post.
Page 19: Installing The Router In A 19-Inch Rack
Figure 8 Installing the front mounting brackets to the two sides of the router Installing the router in a 19-inch rack Put the router on the rack shelf. Slide the router into the rack so the screw holes on the mounting brackets are aligned with holes that are installed with cage nuts on the rack posts.
Page 20: Installing A Power Module
Remove the two grounding screws from the rear panel of the chassis. Attach the grounding screw to the OT terminal of the grounding cable. Use a Phillips screwdriver to fasten the grounding screw into the grounding screw hole. Connect the other end of the grounding cable to the grounding strip of the rack. Figure 10 Connecting the grounding cable to the grounding hole of router IMPORTANT: The resistance reading should be smaller than 5 ohms between the chassis and the ground.
Page 21: Installing An Mpu And A Switching Fabric Module
Figure 11 Installing a power module Installing an MPU and a switching fabric module Installing an RSE-X2 MPU CAUTION: The RUN LED flashes fast when the MPU is starting up. Do not install or remove the MPU during this period. Otherwise, hardware might be damaged.
Page 22: Installing An Lpu
Face the front of the router and locate the slot. Loosen the captive screws with a Phillips screwdriver to remove the filler panel from the slot. Keep the removed filler panel for future use. Insert the SFE-X1 slowly along the slide rails until positioning pins on the backplane are seated in the positioning holes, and then push the ejector levers inward to lock the SFE-X1 in position.
Page 23: Installing A Him/Mim
To install a FIP-210: Face the front of the router and locate the slot to be used. Loosen the captive screws with a Phillips screwdriver to remove the filler panel from the slot. Keep the removed filler panel for future use. Skip this step if you install the FIP-210 to Slot 3 of the HSR6802/HSR6804, or Slot 7 of the HSR6808.
Page 24: Installing A Cf Card
Figure 15 Pushing the MIM into the slot Installing a CF card Push the CF card eject button all the way into the slot, and make sure the button does not project from the panel. Insert the CF card into the slot following the direction shown in Figure 16, and make sure it does not project from the slot.
Page 25 Install the upper and lower slide rails on the chassis as shown in Figure Use a Phillips screwdriver to fasten the fastening screws on the upper and lower slide rails. Figure 17 Installing the upper and lower slide rails Push the air filter along the slide rails from the rear side of the chassis to the front. Figure 18 Inserting the air filter to the slide rail Use a Phillips screwdriver to fasten the captive screws on the rear side of the air filter.
Page 26: Connecting The Power Cord
Figure 19 Fastening the captive screws Installing an air filter on an HSR6808 Face the front of the router. Align the positioning pins on the air filter with the screw holes on the inlet vent area, and use a Phillips screwdriver to fasten the screws on the air filter. Figure 20 Installing an air filter on an HSR6808 Connecting the power cord Connecting an AC power cord...
Page 27: Connecting Dc Power Cords
Figure 21 Connecting an AC power cord to the router Connecting DC power cords Connecting power cords for the PSR650-D WARNING! To avoid connection mistakes, identify the label on the DC power cord. Figure 22 DC power cords To connect DC power cords: Switch off the power supply.
Page 28 Figure 23 Connecting DC power cords Connecting power cords for the PSR1200-D Figure 24 DC power cords To connect DC power cords: Loosen the captive screws on the power module with a Phillips screwdriver to remove the power module connector.
Page 29 Figure 25 Removing the power module connector. Connect the end marked with "– " to the negative terminal (–) on the power module connector and fasten the fastening screw. Connect the end marked with "+"to the positive terminal (+) on the power module connector and fasten the fastening screw.
Page 30 Figure 27 Installing the power module connector to the power module Connect the other end of each power cord to the DC power source. Use cable ties to secure the power cords to the rack post.
Page 31: Connecting Interface Cables
Connecting interface cables Connecting the AUX cable Overview An AUX cable has a crimped RJ-45 connector at one end for connecting to the AUX port of the router, and D9 male connectors at the other end for connecting to the serial port of the modem. Figure 28 AUX cable Connecting the AUX cable Plug the D9 male connector at one end of the AUX cable into the serial port of the modem.
Page 32: Connecting An Ethernet Cable
Connecting an Ethernet cable Overview 10/100 Mbps Ethernet uses category-5 twisted pair cables, while 1000 Mbps Ethernet uses category-5 enhanced or category-6 twisted pair cables. Twisted pair cables include straight-through cables and crossover cables. Category-5 cables provide a transmission frequency of 100 MHz for voice and data transmission; they are mainly used in 100Base-T and 10Base-T networks.
Page 33: Making An Ethernet Cable
For the pinouts of the twisted pair cables, see the following tables. (A and B represent the two ends of a cable, respectively.) Table 7 Straight-through cable pinouts Pinout No. Orange/white Orange/white Orange Orange Green/white Green/white Blue Blue Blue/white Blue/white Green Green Brown/white...
Page 34: Connecting An Ethernet Cable
Transceiver module overview When you use a fiber port, you need an SFP, XFP, or SFP+ transceiver module and a fiber cable with an LC connector. For the compatibility between the cards and transceiver modules, see HP HSR6800 Routers Interface Module Guide.
Page 35: Fiber Cable Overview
There are multiple types of fiber connectors. Figure 34 shows an LC connector. Fiber ports of the HP HSR6800 routers support only LC connectors.
Page 36: Connecting A Fiber Cable
Figure 34 LC connector (1) LC connector (2) Optical fiber Connecting a fiber cable WARNING! Do not stare into any fiber port when you connect an optical fiber. The laser light emitted from the optical fiber might hurt your eyes. To connect a fiber cable: Remove the dust plug from a fiber port of the router.
Page 37: Connecting An E1/T1 Cable
Figure 35 Connecting a fiber cable Examine the LINK LED after connection. If the LED is on, the optical fiber link is present. If the LED is off, no link is present. This might be because the TX and Rx port of the optical fiber are not connected correctly.
Page 38: Connecting An E1/T1 Cable
• insertion, which might damage the interface module or even the router. HP recommends that you install a lightning protector at the input end of the 8T1 cables to protect them • against lightning strikes more efficiently when they are led outdoors.
Page 39 Figure 38 Connecting an E1 75-ohm cable • If you want to extend the cable, connect each BNC connector of the E1 75-ohm cable to one end of a coaxial connector, and connect the remote device to the other end of the coaxial connector through an E1 75-ohm adapter cable.
Page 40: Connecting A Ce3/Ct3 Cable
Overview CAUTION: HP recommends that you install a special lightning protector at the input end of the E3/T3 cables to protect them against lightning strikes more efficiently when they are routed outdoors. You can use a E3/T3 interface cable to connect the MIM- 1 CE3 and MIM- 1 CT3 modules.
Page 41: Connecting A Serial Port Cable
Figure 43 Connecting a CE3/CT3 cable Connecting a serial port cable Overview You can use a serial port cable to connect to the MIM-2SAE/MIM-4SAE/MIM-8SAE module. Select a serial port cable according to the link type. Figure 44 V.24 DTE cable Figure 45 V.24 DCE cable...
Page 42 Figure 46 V.35 DTE cable Figure 47 V.35 DCE cable Pos.28 Pos.1 Figure 48 X.21 DTE cable Pos.1 Pos.1 Pos.15 Pos.28 Figure 49 X.21 DCE cable...
Page 43: Connecting A Serial Port Cable
Figure 50 RS449 DTE cable Figure 51 RS449 DCE cable Figure 52 RS530 DTE cable Figure 53 RS530 DCE cable Connecting a serial port cable Check port type of the peer device and choose the synchronous serial interface cable of correct type.
Page 44 Identify the LINK LED on the SAE panel. If the LED is on, a link is present. If the LED is off, a fault has occurred on the link and signal is out of synchronization. In this case, examine the link.
Page 45: Accessing The Router
Accessing the router Login methods The following logins methods are available for you to log in to the router: • Logging in through the console port, which is the most common way to log in to a router and also the prerequisite for configuring other login methods.
Page 46: Setting Terminal Parameters
Figure 54 Connecting the console cable Setting terminal parameters Select Start > All Programs > Accessories > Communications > HyperTerminal. The Connection Description dialog box appears. Figure 55 Connection description Select the serial port to be used from the Connect using list, and click OK.
Page 47 Figure 56 Setting the serial port used by the HyperTerminal connection Set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to 1, and Flow control to None, and click OK. Figure 57 Setting the serial port parameters Select File >...
Page 48 Figure 58 HyperTerminal window On the Settings tab, set the emulation to VT100 and click OK. Figure 59 Setting terminal emulation in test Properties dialog box...
Page 49: Powering On The Router
Power on the router, and you can see the following information: System is starting... Booting Normal Extend BootWare..The Extend BootWare is self-decompressing......Done! **************************************************************************** HP HSR68 BootWare, Version 0.17 **************************************************************************** Copyright (c) 2010-2012 Hewlett-Packard Development Company, L.P. Compiled Date : Apr 10 2012...
Page 50: Logging In To The Router Through Telnet/Ssh
Specify an IP address for the PC, making sure the PC and the port are in the same network segment. For more information about how to log in to the router through Telnet/SSH, see HP HSR6800 Routers Configuration Guides. Logging in to the router through the AUX port After powering on the router, connect the console cable to the console port.
Page 51: Configuring Basic Settings
Connect the RJ-45 connector to the AUX port of the router. Then you can log in to the router through the AUX port. For more information about how to log in to the router through an AUX port, see HP HSR6800 Routers Fundamentals Configuration Guides.
Page 52: Replacement Procedures
Replacement procedures All modules of the HP HSR6800 routers are field replaceable. Safety recommendations Always wear an ESD wrist strap or ESD gloves when you replace the modules. All transceiver modules are hot swappable. If you need to replace LPUs or HIMs/MIMs when the router is powered on, use the command remove slot slot-number to stop them from working first.
Page 53: Replacing An Mpu And A Switching Fabric Module
If the router is installed with two MPUs, make sure both MPUs operate correctly before replacement. • To replace the active MPU, HP recommends that you execute the slave switchover command in the system view of the active MPU to trigger an active and standby switchover. For more information about the slave switchover command, see HP HSR6800 Routers High Availability Command Reference.
Page 54: Replacing An Lpu
Figure 62 Pulling the SFE-X1 out of the slot (HSR6808) Install a new SFE-X1. For the installation procedure, see "Installing an SFE-X1 switching fabric module." If you do not install a new SFE-X1 in the slot, install a filler panel. Replacing an LPU CAUTION: To avoid hardware damage, do not replace the LPU when its RUN LED is fast flashing.
Page 55: Replacing A Him/Mim
Figure 63 Pulling the FIP module out of the slot Install a new FIP module. For the installation procedure, see "Installing an LPU." If you do not install a new FIP module in the slot, install a filler panel. Replacing a HIM/MIM The procedures for replacing HIMs and MIMs are similar.
Page 56: Replacing A Cf Card
Replacing a CF card CAUTION: To avoid hardware damage, do not remove the CF card when the router is booting or the CF LED is flashing. To replace a CF card: Press the CF card eject button of the CF card reader so that the eject button projects from the panel. Press the eject button again to eject the CF card part-way out of the CF card reader, and then pull the CF card out of the CF card reader.
Page 57: Replacing A Fan Tray
Replacing a fan tray CAUTION: Keep your hands away from the spinning fan blades when removing the fan tray. • Do not keep the router working without a fan tray for more than two minutes because poor ventilation • might result in damage to the router. Replacing a fan tray for an HSR6802/HSR6804 router The methods for replacing fan trays for the HSR6802 and HSR6804 are the same.
Page 58: Replacing An Air Filter
Figure 68 Pulling out the fan tray Replacing an air filter IMPORTANT: You can clean the air filter with water, but wait until it is completely dry before installing it again. Replacing an air filter for an HSR6802/HSR6804 router Face the left side of the router. Use a Phillips screwdriver to completely loosen the captive screws of the air filter.
Page 59: Replacing An Air Filter For An Hsr6808 Router
Replacing a memory module CAUTION: Use the memory modules provided by HP only. Otherwise, the router might be unable to operate correctly. The MPUs and LPUs are equipped with memory modules. Before you install or remove a memory module, remove the MPU or LPU from the chassis first. For more information, see "Replacing an MPU and a...
Page 60: Memory Module Structure
For the memory module specifications, see "Appendix A Chassis views and technical specifications." Memory module structure Figure 72 Memory module structure (DDR2) (1) Connector edge (2) Polarization notch (3) Latch notch Figure 73 Memory module structure (DDR3) (1) Connector edge (2) Polarization notch (3) Latch notch Replacing a memory module...
Page 61 Carefully and firmly press the memory module at both ends until you hear a click. This indicates the memory module is seated in the memory module slot. Check that the release latches have firmly locked the memory module in position. Figure 74 Replacing a memory module...
Page 62: Hardware Management And Maintenance
Hardware management and maintenance The output depends on your router model and software version. For more information about the commands used in this chapter, see HP HSR6800 Routers Command References. Displaying the hardware information of the router Displaying the version information of the router Use the display version command to display software and hardware version information of the router.
Page 63: Displaying The Running Statistics For The Router
[FIXED PORT] MGE4/0/0 (Hardware)Ver.B, (Driver)1.0, (Cpld)1.0 Displaying the running statistics for the router For diagnosis or troubleshooting, you can use separate display commands to collect running status data module by module, or use the display diagnostic-information command to bulk collect running data for multiple modules.
Page 64: Displaying The Electrical Label Data
Slot 0: DEVICE_NAME: RT-RSE-X2 DEVICE_SERIAL_NUMBER: 210231A1RG0000000002 MAC_ADDRESS: 00FE-1230-1230 MANUFACTURING_DATE: 2011-12-12 VENDOR_NAME:HP Use the display device manuinfo slot slot-number command to display the electrical label data for • the card in the specified slot. <Sysname> display device manuinfo slot 0 Slot 0:...
Page 65: Displaying The Cpu Usage Statistics
Table 12 Command output Field Description DEVICE_NAME Card type. DEVICE_SERIAL_NUMBER Card serial number. MAC address of the card: • MAC_ADDRESS An MPU has a MAC address. • An LPU does not have a MAC address, and the field displays NONE. MANUFACTURING_DATE Manufacturing date of the card.
Page 66: Displaying The Cf Card Information
<Sysname> display memory System Total Memory(bytes): 4069505360 Total Used Memory(bytes): 277820968 Used Rate: 6% Table 14 Command output Field Description System Total Memory(bytes) Physical memory size (in bytes) of the MPU. Total Used Memory(bytes) Used memory size (in bytes) of the MPU. Used Rate Memory usage of the MPU.
Page 67: Displaying The Power Module Operating Status
Field Description Fan state: • Normal—The fan is operating correctly. State • Absent—The fan is not in position. • Fault—The fan has failed. Displaying the power module operating status Use the display power command to display the power module operating status. <Sysname>...
Page 68: Port Configuration And Management
Table 18 Command output Field Description SlotNo Slot number of the card. Temperature Current temperature of the card. Lower limit Low temperature threshold of the card. Upper limit High temperature threshold of the card. Port configuration and management Configuring a combo interface A combo interface is a logical interface that comprises an SFP port of a transceiver module and an RJ-45 Ethernet port.
Page 69: Displaying And Verifying Transceiver Modules
The system outputs alarm information for you to locate and troubleshoot faults of transceiver modules. For the HP-customized transceiver modules, the system can also monitor the key parameters, such as temperature, voltage, laser bias current, TX power, and RX power. When these parameters are abnormal, you can take corresponding measures to prevent transceiver module faults.
Page 70: Active And Standby Switchover For Mpus
[ interface-type interface-number ] modules. module in a specified interface. For more information about the transceiver module displaying commands, see HP HSR6800 Routers Command References. Active and standby switchover for MPUs CAUTION: Do not execute any command on the standby MPU.
Page 71: Displaying The Exception Handling Method
reboot—Rebooting the failed MPU so that the MPU restores to normal operating status. • • maintain—Maintaining the current status of the failed MPU so that the system does not take any restoration measures. Some software faults are hard to reproduce, and the printed information will be lost after the router reboots.
Page 72 For data security, if you reboot the router while the router is performing file operations, the router does not reboot. The precision of the rebooting timer is 1 minute. One minute before the rebooting time, the router prompts “REBOOT IN ONE MINUTE” and reboots in one minute. If the main startup configuration file does not exist, do not use the reboot command to reboot the router or the active MPU.
Page 73: Troubleshooting
Troubleshooting IMPORTANT: The barcode stuck on the router chassis contains production and servicing information. Before you return a faulty router for serving, provide the barcode information of the router to your local sales agent. MPU failures RUN LED is off When the RUN LED of the MPU is off, it indicates that the MPU is powered off or faulty.
Page 74: Palm Led Is Steady On
PALM LED is steady on If the PALM LED of the MPU is steady on, it indicates that exceptions have occurred to the power supply system. The following reasons might apply: • Mismatch between the power supply and power consumption. For example, if an HSR6808 is installed with a 650 W power module but two SAP-48GBE modules, the power available is not sufficient for the whole power consumption and one SAP module cannot be powered on.
Page 75: Run Led Fast Flashes
%Apr 26 16:46:32:169 2012 HP DRVMSG/1/InSufficientPwr: No sufficient power, failed to power on slot 3. If the usable power is normal, the LPU is faulty. Execute the display version command. The following output appears.
Page 76: Red Power Led Is On
Fan tray is absent After the router is booted, the following information might appear on the configuration terminal: #Jun 14 11:57:27:778 2012 HP DEVM/1/FAN STATE CHANGES TO FAILURE: Trap 1.3.6.1.4.1.25506.8.35.12.1.6<hhpfanfailure>: fan ID is 1 %Jun 14 11:57:27:779 2012 HP DEVM/3/FAN_ABSENT: Fan 1 is absent.
Page 77: Him/Mim Failures
When a HIM/MIM is plugged while the router is running, the following information might appear on the configuration terminal: %Jun 14 11:12:36:037 2012 HP DRVICOUT/1/DrvIcOutStr: -Slot=4; Card in Slot 4 Sublot 1 can not be recognized ! The output indicates that the HIM/MIM is faulty or the router cannot recognize the HIM/MIM.
Page 78: No Response From The Serial Port
Verify that the Data bits field is set to 8 for the console terminal. If the Data bits field is set to 5 or 6, the console terminal will display garbled characters. Verify that the Bits per second field is set to 9600 bps. An incorrect Bits per second might also cause the configuration terminal to display garbled characters.
Page 79: Examining The State Of Password Recovery Capability
Press Ctrl+D to access BASIC-BOOTWARE MENU Press Ctrl+T to start memory test Booting Normal Extend BootWare..The Extend BootWare is self-decompressing......Done! **************************************************************************** HP Router BootWare, Version 1.04 **************************************************************************** Copyright (c) 2010-2012 Hewlett-Packard Development Company, L.P. Compiled Date : Dec 26 2012...
Page 80: Dealing With Console Login Password Loss When Password Recovery Capability Is Enabled
The router starts up with empty configuration. To use the configuration in the next-startup configuration file, load the file in system view. <HP> system-view [HP] configuration replace file startup.cfg Current configuration will be lost, save current configuration? [Y/N]:n Info: Now replacing the current configuration. Please wait...
Page 81: Dealing With User Privilege Level Password Loss When Password Recovery Capability Is Enabled
<HP> system-view [HP] user-interface console 0 [HP-ui-console0] authentication-mode password [HP-ui-console0] set authentication password cipher 123456 To make the settings take effect after a reboot, save the running configuration to the next-startup configuration file. [HP] save Dealing with user privilege level password loss when password recovery capability is enabled Reboot the router to access the EXTEND-BOOTWARE menu, and then enter 8.
Page 82: Dealing With Password Loss When Password Recovery Capability Is Disabled
To make the setting take effect after a reboot, save the running configuration to the next-startup configuration file. [HP] save Dealing with password loss when password recovery capability is disabled Reboot the router to access the EXTEND-BOOTWARE menu, and enter 5.
Page 83: Cooling System Failure
If the temperature inside the router exceeds the critical temperature threshold, but the fans are running correctly and the router is well ventilated, power off the router immediately and contact your local sales agent. For more information about the display environment command, see HP HSR6800 Routers Fundamentals Command Reference. Ethernet port failure When you use unshielded twisted pairs to connect Ethernet ports and at least one end of the link supports 100Base-TX, you should consider the rate matching of both ends.
Page 84: Him/Mim, Cable, And Connection Failure
No link is present for the end operating at 100 Mbps. • • A link is present for the end operating at 10 Mbps, but the physical layer LED (for example, the Active LED) keeps flashing, and the port cannot transmit or receive traffic correctly. For the copper FE ports and GE ports, both the rate and duplex mode are auto-negotiated by default.
Page 85: Ftp Upgrade Failure
To solve this problem, configure the network port correctly, and make sure the network port is up and you can successfully ping the TFTP server from the network port. FTP upgrade failure Start the router, and upgrade the software through FTP. The following problems might occur: The CF card has no enough space.
Page 86: Appendix A Chassis Views And Technical Specifications
Appendix A Chassis views and technical specifications Chassis views CAUTION: Do not use the rear cover handle when you move the router chassis. This handle is designed to help you remove the rear cover and cannot support the chassis weight. HSR6802 Figure 76 HSR6802 front view (1) MPU slots (Slot 0 and Slot 1)
Page 87: Hsr6804
Figure 77 HSR6802 rear view (1) Rear cover handle (2) Chassis handle (3) Grounding screw and sign (4) Air vents HSR6804 Figure 78 HSR6804 front view (1) MPU slots (Slot 0 and Slot 1) (2) Fan tray (3) Power module slots (4) LPU slots (Slot 2 to Slot 5)
Page 88 Figure 79 HSR6804 rear view (1) Rear cover handle (2) Chassis handle (3) Grounding screw and sign (4) Air vents...
Page 89: Hsr6808
HSR6808 Figure 80 HSR6808 front view (1) Fan tray (2) Cable management bracket (3) LPU slots (Slot 0 to Slot 3 and Slot 7 to Slot 9) (4) MPU slots (Slot 4 and Slot 5) (5) Switching fabric module or LPU slot (Slot 6) (6) Air intake vents (An optional air filter can be installed.) (7) Power module slots...
Page 90: Dimensions And Weight
Figure 81 HSR6808 rear view (1) Chassis air exhaust vents (2) Chassis handle (3) Rear cover handle (4) Grounding screw and sign (5) Power module air exhaust vents Dimensions and weight Table 21 Router dimensions and weight Item HSR6802 HSR6804 HSR6808 308 mm (12.13 in) (7 886 mm (34.88 in)
Page 91: Power Consumption
Model Net weight Dimensions (H × W × D) FIP-110 3.25 kg (7.16 lb) 45 × 399 × 412 mm (1.77 × 15.71 × 16.22 in) FIP-210 3.35 kg (7.39 lb) 45 × 399 × 412 mm (1.77 × 15.71 × 16.22 in) FIP-600 3.55 kg (7.83 lb) 45 ×...
Page 92: Power Module
Power module The HSR6800 routers support hot-swappable AC and DC power modules, but an AC and a DC power module cannot work together. You can install one or, for redundancy, multiple power modules, but the power modules in use must have the same specifications.
Page 93: Dc Power Module
PSR1200-A Figure 83 PSR1200-A view (1) AC-input power receptacle (2) Power switch (3) Handle (4) Power module status LED Table 26 PSR1200-A specifications Item Remarks Rated input voltage 100 VAC to 240 VAC @ 50 or 60 Hz Maximum input current 16 A Maximum power 1213 W...
Page 94 Table 27 PSR650-D specifications Item Remarks Rated input voltage –48 VDC to –60 VDC Maximum input current 25 A Maximum power 650 W PSR1200-D Figure 85 PSR1200-D view (1) Power module connector (2) Power switch (3) Handle (4) Power module status LED Table 28 PSR1200-D specifications Item Remarks...
Page 95: Fan Tray Specifications
Fan tray specifications Figure 86 Fan tray of the HSR6802 Figure 87 Fan tray of the HSR6804 (1) Fan (2) Fan tray status LED (RUN) (3) Alarm LED (ALM) (4) Handle (5) Rotating blade hazard label...
Page 96: Mpu
5.3 kg (11.68 lb) Noise level 57.1 dBA 57.4 dBA 58.1 dBA Heat dissipation 1778 BTU/h 3115 BTU/h 5988 BTU/h Automatic fan speed adjustment Supported Failsafe Supported Hot swapping Supported RSE-X2 The RSE-X2 is supported by the HP HSR6800 routers.
Page 97 RSE-X2 front panel Figure 89 RSE-X2 front panel (1) Management Ethernet port (MANAGEMENT) (2) AUX port (AUX) (3) MPU status LEDs (4) Reset button (RESET) (5) USB port (6) Console port (CONSOLE) (7) CF card slot (8) CF card button (9) CF card status LED RSE-X2 specifications Item...
Page 98: Components
CF card CAUTION: Use CF cards provided by HP only. The router might be incompatible with other CF cards. A compact flash (CF) card stores logs, system software image files, and configuration files. The router is equipped with a built-in CF card, which is identified with cfa0. In addition, the router provides an external CF card slot to expand the storage space.
Page 99 Item Specification Connects to the serial port of a local PC or to a remote PC through dialup Supported service connection (using a pair of modems at the two ends) Management Ethernet port The management Ethernet port is a 10Base-T/100Base-TX/1000Base-T autosensing RJ-45 port. It allows you to upgrade software and manage the router through a network management server without using any service interface of the router.
Page 100: Sfe-X1
SFE-X1 The SFE-X1 with a built-in 1024-Gbps switch fabric is specially designed for the HSR6808 by HP to improve the router's switching capability. NOTE: Only the HSR6808 routers support SFE-X1. SFE-X1 front panel Figure 90 SFE-X1 front panel (1) Captive screw...
Page 101: Lpu
FIP-110 FIP-110 front panel Figure 91 FIP-110 front panel (1) Slot 4 (2) Slot 3 (3) Combo interface 1 (4) Combo interface 0 (5) Slot 1 (6) Slot 2 (7) OPEN BOOK mark FIP-110 specifications Item Remarks Flash 4 MB •...
Page 102 For more information about the combo enable { copper | fiber } command, HP HSR6800 Routers Interface Command Reference Use transceiver modules for the fiber ports provided by HP only. The router might be incompatible with •...
Page 103: Fip-210
Central Transmission Max. transmission Model Connector Optical fiber wavelength rate distance 9/125 μm 10 km SFP-GE-LX-SM131 1310 nm single-mode 1250 Mbps (6.21 miles) optical fiber 9/125 μm 40 km SFP-GE-LH40-SM1 1310 nm single-mode 1250 Mbps (24.86 miles) optical fiber 9/125 μm 40 km SFP-GE-LH40-SM1 1550 nm...
Page 104: Fip-300
For more information about the combo enable { copper | fiber } command, HP HSR6800 Routers Interface Command Reference Use transceiver modules for the fiber ports provided by HP only. The router might be incompatible with •...
Page 105 For more information about the combo enable { copper | fiber } command, HP HSR6800 Routers Interface Command Reference Use transceiver modules for the fiber ports provided by HP only. The router might be incompatible with •...
Page 106: 100
Maximum interface modules provided by FIP-300 in full configuration FIP/Interface module SR6604-X SR6608-X SR6616-X FIP-300 FIP-310 The FIP-310 supports HIMs and MIM, and it provides 4 combo interfaces and 2 SFP ports. FIP-310 front panel Figure 94 FIP-310 front panel (1) Combo interface 1 (2) Combo interface 3 (3) SFP+ port 0...
Page 107 HP HSR6800 Routers Interface Command Reference • Use transceiver modules for the fiber ports provided by HP only. The router might be incompatible with transceiver modules from other manufacturers. The system generates an alarm when a transceiver module from another manufacturer is installed.
Page 108: 102
FIP/Interface module SR6604-X SR6608-X SR6616-X FIP-600 FIP-600 front panel Figure 95 FIP-600 front panel (1) Combo interface 1 (2) Combo interface 0 (3) Slot 1 (4) Slot 2 (5) OPEN BOOK mark FIP-600 specifications Item Remarks Flash 8 MB • Default—Two 2-GB DDR3 SDRAMs Memory type and size •...
Page 109: Sap-48Gbe
For more information about the combo enable { copper | fiber } command, HP HSR6800 Routers Interface Command Reference Use transceiver modules for the fiber ports provided by HP only. The router might be incompatible with •...
Page 110: Sap-24Gbp
For more information, see Table SAP-24GBP CAUTION: Use transceiver modules provided by HP only. The router might be incompatible with other transceiver modules and thus displays alarms automatically. SAP-24GBP front panel Figure 97 SAP-24GBP front panel (1) SFP ports 0 to 23...
Page 111 Item Remarks 24 fiber Ethernet ports Supporting 100/1000 Mbps autosensing Supporting the following types of transceiver modules: • 100 Mbps SFP fiber transceiver modules • 1000 Mbps SFP fiber transceiver modules Fixed Ethernet ports (SFP) • 100/1000 Mbps SFP fiber transceiver modules •...
Page 112: Sap-48Gbp
(43.50 miles) optical fiber SAP-48GBP CAUTION: Use transceiver modules provided by HP only. The router might be incompatible with other transceiver modules and thus displays alarms automatically. SAP-48GBP front panel Figure 98 SAP-48GBP front panel (1) SFP ports 0 to 47...
Page 113: Sap-4Exp
SAP-48GBP fixed Ethernet port specifications The fixed Ethernet ports of the SAP-48GBP have the same specifications as the fiber ports of the FIP- 1 10 combo interfaces. For more information, see Table Transceiver modules for the SAP-48GBP and the SAP-24GBP fiber ports are the same. For more information, see Table SAP-4EXP...
Page 114: Spe/Oap
(OAP), the SPE can provide multiple services. For more information about the SPE and OAP, see relevant datasheet. HIM/MIM HP HSR6800 routers support HIMs and MIMs. Both HIMs and MIMs provide synchronous serial ports, Ethernet ports and E1 ports. For more information, see HP HSR6800 Routers Interface Module Guide.
Page 115: Appendix B Leds
Appendix B LEDs HP HSR6800 routers provide LEDs for FRUs to indicate their operating status. MPU and switching fabric module LEDs Figure 100 RSE-X2 LEDs Table 42 RSE-X2 LED description Status Description No CF card is present or the CF card is not recognizable.
Page 116 Status Description The MPU is in standby state. Steady on The MPU is in active state. (green) No power input is available, or the MPU has failed. Slow flashing (1 The MPU is operating correctly. The application software is being loaded. (green) CAUTION: Fast flashing (8 Hz)
Page 117: Lpu Leds
LPU LEDs FIP LEDs FIP-110/FIP-210/FIP-600 LEDs Figure 102 FIP-110 status LED Figure 103 FIP-210 status LED Figure 104 FIP-600 status LED...
Page 118 Table 44 FIP-110/FIP-210/FIP-600 LED description Status Description No link is present. Steady green A 1000 Mbps link is present. Data is being received or transmitted at a rate of Status LEDs of Flashing green 1000 Mbps. GE 0 to GE 1 Steady yellow A 10/100 Mbps link is present.
Page 119 Status Description No link is present. Steady green A 1000 Mbps link is present. Status LEDs of Data is being received or transmitted at 1000 SFP 0 to SFP 11 Flashing green Mbps. (yellow/green) Steady yellow The transceiver module has failed the POST. No power input is available or the FIP has failed.
Page 120: Sap Leds
Status Description (green) Application software is being loaded. Fast flashing (8 CAUTION: To avoid the hardware damage, do not power off the router, or insert or remove the FIP. No link is present. Steady green A 10 Gbps link is present. Flashing green Data is being received or transmitted at 10 Gbps.
Page 121 Figure 108 SAP-24GBP LEDs Table 48 SAP-24GBP LED description Status Description No power input is available or the SAP-24GBP has failed. Slow flashing (1 The SAP-24GBP is operating correctly. Application program is being loaded or the SAP-24GBP is not operating. (green) CAUTION: Fast flashing (8 Hz)
Page 122 Table 49 SAP-48GBP LED description Status Description No power input is available or the SAP-48GBP has failed. Slow flashing (1 Hz) The SAP-48GBP is operating correctly. Application program is being loaded or the SAP-48GBP is not operating. CAUTION: (green) Fast flashing (8 Hz) To avoid hardware damage, do not power off the router, or insert or remove the SAP-48GBP when application program is being loaded.
Page 123: Spe Leds
SPE LEDs For SPE LED description, see the corresponding datasheet. HIM/MIM LEDs For HIM/MIM LED description, see HP HSR6800 Routers Interface Module Guide. Power module LEDs Figure 111 PSR650-A AC power module LED Figure 112 PSR1200-A AC power module LED...
Page 124: Fan Leds
Table 51 AC/DC power LED description Status Description Steady green The power module is operating correctly. Power LED Steady red The power module is faulty. No power is input. Fan LEDs Figure 115 Fan LEDs of the HSR6802...
Page 125 Figure 116 Fan LEDs of the HSR6804 Figure 117 Fan LEDs of the HSR6808 Table 52 Fan LED description Status Description The system is powered off or the fan tray is faulty. Steady on The fan is operating correctly. (green)
Page 126 Status Description The fan is operating correctly. Steady on The fan is faulty. (red)
Page 127: Appendix C Arranging Slots And Numbering Interfaces
Appendix C Arranging slots and numbering interfaces Slot arrangement The router provides many types of interfaces, such as console, AUX, GigabitEthernet, serial (synchronous), POS, and E1 ports. This chapter describes how these interfaces are numbered. Figure 118 Slot arrangement on the HSR6802 Figure 119 Slot arrangement on the HSR6804...
Page 128: Available Slots For Cards
Figure 120 Slot arrangement on the HSR6808 NOTE: Figure 118 through Figure 120, the blue and dark numbers represent slot numbers of the cards and power modules, respectively. Available slots for cards Card HSR6802 HSR6804 HSR6808 RSE-X2 (supporting Slot 0 and Slot 1 Slot 0 and Slot 1 Slot 4 and Slot 5 1+1 redundancy)
Page 129: Numbering Interfaces
Numbering interfaces Before installing a HIM/MIM, you must install a FIP. A FIP-210 supports both HIMs and MIMs, while a FIP- 1 10 supports only MIMs, and a FIP-600 supports only HIMs. The interfaces of the router are numbered in the form of interface-type X/Y/Z, Where, interface-type—Type of the interface such as GE port and serial port.
Page 131: Appendix D Cable Management
Appendix D Cable management When the router is mounted in a 19-inch standard rack, the interface cables are routed through the cable management brackets, bound at cabling racks on chassis sides, and then routed up or down, depending on the available equipment room condition. The power cables run along the two sides of the front of the chassis and out of the chassis either from the chassis top or the raised floor depending on the equipment room conditions (power distribution cabinet, lightning protection box, and connector strip, etc.) of the exchange office.
Page 132: Cable Management Guidelines
Cable management guidelines When you route and bundle up cables, follow these guidelines: • Bind and route the cables neatly inside the rack, and make sure the cables are not kinked or bent. Figure 121 Correct and incorrect cable binding Route different types of cables (for example, power cables, and signal cables) separately.
Page 133 When you bend cables, bind cables as shown in Figure 123. To avoid cable core break due to • excessive stress, do not tie up the cables in the bending area. Figure 123 Binding the cables Route, bind, and attach excess cables for easy, safe maintenance activities and correct operations. •...
Page 134: Cable Routing Example
Table 53 Cable bundling specifications Cable bundle diameter (mm) Space between bundles (mm) 80 to 150 10 to 30 150 to 200 200 to 300 Do not tie cables or bundles in a knot. • • The metal parts of the crimped cold-pressed terminal blocks (such as circuit breaker) cannot protrude beyond the blocks.
Page 135: Support And Other Resources
Related information Documents To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals For related documentation, navigate to the Networking section, and select a networking category. •...
Page 136: Conventions
Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax choices separated by vertical bars, from which { x | y | ...
Page 137 Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.
Page 138: Index
Connecting the AUX cable,25 Installing optional components,18 Connecting the power cord,20 Installing the router in a 19-inch rack,1 1 Contacting HP,129 Conventions,130 Labeling cables,125 Cooling system failure,77 Logging in through the console port,39 Logging in to the router through Telnet/SSH,44...
Page 139 Power module specifications,86 Powering on the router,43 Safety recommendations,1 Safety recommendations,46 Slot arrangement,121 Rebooting a card or router,65 Software upgrade failures,78 Related information,129 LEDs,1 17 Replacing a CF card,50 SPE/OAP specifications,108 Replacing a fan tray,51 Specifications of MPUs and switching fabric Replacing a memory module,53 modules,90...

HP HSR6800 Installation Manual

Quick Links

Installation Guide

Troubleshooting

Related Manuals for HP HSR6800

Summary of Contents for HP HSR6800

Table of Contents