Sharp MX-M200D Service Manual page 82

Main Sub
code code
F2 04 Content Improper cartridge (destination error, life cycle
error)
Detail The destination of the machine differs from that
of the CRUM.
The life cycle information is other than "Not
used (FFh)".
Cause CRUM chip defect.
Improper developing unit .
Check Replace the CRUM chip.
and Replace the developing unit.
remedy
Identificat The trade mark code of the CRUM differs.
ion error The company code of the CRUM differs.
Model The boot program model code does not
error coincide with the CRUM model code.
Type When the CRUM type is other than genuine/
error conversion/production rotation.
Destinatio The machine destination differs from the
n error CRUM destination.
Data When an error value is included in the initial
abnormali check information. When the max. toner supply
ty time is 00.
When the print hard stop is 00.
Misc error When the Misc information is other than "Not
used (FFh)".
40 Content ATC sensor abnormality
Detail ATC sensor value abnormality
Cause Connector connection trouble
Toner cartridge installation trouble
Sensor breakdown
Check Connect the connector again.
and Install the developing unit again.
remedy Replace the developing unit with a normal one.
F5 02 Content Copy lamp lighting abnormality.
Detail The copy lamp does not turn on.
Cause Copy lamp abnormality.
Copy lamp harness abnormality.
CCD PWB harness abnormality.
Check Use SIM 5-3 to check the copy lamp
and operations.
remedy
When the copy lamp lights up.
Check the harness and the connector between
the CCD unit and the MCU PWB.
When the copy lamp does not light up.
Check the harness and the connector between
the copy lamp unit and the MCU PWB.
Replace the copy lamp unit.
Replace the MCU PWB.
F6 00 Content FAX board communication trouble.
Detail FAX board communication error.
Cause No command can be sent from the MCU to the
FAX.
Check Check connection of the FAX board.
and Replace the FAX board.
remedy
10 Content FAX board trouble.
Detail FAX board abnormality detection.
Cause FAX controller and FAX board memory
abnormality.
Check Replace the FAX board.
and
remedy
Details of trouble
MX-M200D TROUBLE CODE LIST 9-3
Main Sub
code code
F6 80 Content FAX board communication trouble (Protocol).
Detail A break error occurs in communication
between the MCU and the FAX board.
Cause MCU PWB connector connection failure/
Garbled data.
Check Check connection of the FAX board.
and Replace the FAX board.
remedy Reset the machine (Power OFF/ON).
81 Content FAX board communication trouble (Parity).
Detail A parity error occurs in communication.
between the MCU and the FAX board.
Cause MCU PWB connector connection failure/
Garbled data.
Check Check connection of the FAX board.
and Replace the FAX board.
remedy Reset the machine (Power OFF/ON).
82 Content FAX board communication trouble (Overrun).
Detail An overrun error occurs in communication
between the MCU and the FAX board.
Cause MCU PWB connector connection failure/
Garbled data
Check Check connection of the FAX board.
and Replace the FAX board.
remedy Reset the machine. (Power OFF/ON).
84 Content FAX board communication trouble (Framing).
Detail A framing error occurs in communication
between the MCU and the FAX board.
Cause MCU PWB connector connection failure/
Garbled data.
Check Check connection of the FAX board.
and Replace the FAX board.
remedy Reset the machine (Power OFF/ON).
88 Content FAX board communication trouble (Time out).
Detail FAX board communication error.
Cause There is no respond command from the FAX
for 30sec or more.
Check Check connection of the FAX board.
and Replace the FAX board.
remedy Reset the machine (Power OFF/ON).
97 Content Combination error between the FAX unit and
the main unit
Detail Combination error between the FAX unit and
the main unit
Cause When this fax unit is installed to the machine
that can not install this.
Check Check the model name of the main unit
and
remedy
99 Content Machine - FAX language error.
Detail Discrepancy of the destination of the machine
and the FAX board.
Cause The destination of the machine differs from that
of the FAX board.
When installing to the machine that can install
only AR-FX11.
Check Change the destination setting with SIM26-6.
and Replace the FAX board with one which.
remedy conforms to the destination of the machine.
F9 00 Content MX-NB10 board communication trouble.
Detail MX-NB10 print data reception error.
Cause Print data cannot be received from the MX-
NB10 for 3 min or more.
Check Reset the machine (Power OFF/ON).
and
remedy
Details of trouble