Panasonic Strata Se General Description Manual page 95

5) Depress the 01 and 03 keys on station 13.
0 The corresponding LEDs go on.
6) Depress the m key on station 13.
l
Station 13: All LEDs (except SPKR and
MIC) begin blinking.
7) Depress and release the SET switch again.
l
SET LED goes off.
e Station 13: LEDs go off.
8) Cycle the power switch
OFF
and ON.
04.04 STRATA Vie:
NOTE.
Verify that the battery on the VMAU is con-
nect& to e::sure ihat data e.itered after sys-
tem initialization is not lost due to power fail-
ure. (The SET LED cannot function if the
battery is not connected.)
1) Place the system power switch in the ON po-
sition.
2) Depress the
INT
switch on the HKSU, and
hold it in.
3) Depress the
SET
switch and allow it to lock.
l
SET LED goes on.
l
Station 17: All LEDs (except SPKR & MIC)
blink continuously.
4) Depress and release the SET switch again.
l
SET LED goes off.
l
Station 17: LEDs go off.
5) Release the
INT
switch.
6)
C:'c!e TO power switc.? C!FF and OF!.
04.10 1 Clearing Automatic Dialing
04.11
The Automatic Dialing memory con-
tains random numbers when the system is po-
wered up initially. The memory, therefore, must
be cleared to prevent meaningless numbers
from being dialed.
IMPORTANT!
Station 13/17 may be equipped with
either a IO- or a 20-key EKT. Prior to per-
forming the procedure that follows; refer
to Paragraph 02.10 for instructions on us-
ing a 1 O-key EKT for programming.
04.12
To clear the Automatic Dialing (-System
and -Station) memory (up to 40 numbers), pro-
ceed as follows:
PROGRAMMING PROCEDURES
SECTION 500-036-300
JANUARY 1988
1) Lock in the SET switch.
l
Station 13/l 7: LED 19 lights steadily.
2)
To clear station 10 - 33, depress the em
key and dial 2 1 a.
l
SPKR LED flashes continuously.
l
Depress keys a Jj a a.
l
Depress the m key.
3) To clear station 34 - 57, depress the B
key and dial $ J g,
l
SPKR LED flashes continuously.
l
Depress keys E a
q q
.
l
Depress the m key.
4) To clear station 58 - 65 and system speed
dial, depress the m kay and dial 2 15.
l
SPKR LED flashes continuously.
l
Depress keys E 3 m a.
l
Depress the m key.
5) Release the SET switch.
l
The SET LED and LED 19 on station
13/17 go off.
04.20 Alphanumeric Messaging Initializa-
tion
NOTE.
There are 40 messages available in system
memory (60 - 991, and i0 availabie at each
station (10 - 19).
04.21
To initialize system alphanumeric mes-
sages, follow these procedures:
1) Lock in the SET switch.
l
Station 13/17: LED 19 lights steadily.
2) To clear codes 62: - 53, depress the B
key and dial 11 8.
l
SPKR LED flashes continuously.
l
Depress keys a a a
q
.
l
Depress the m key.
04.22 To initialize station alphanumeric mes-
sages, follow these procedures:
1) Lock in the
SET
switch.
l
Station 13/l 7: LED 19 lights steadily.
2) To clear codes 10 - 19, depress the w
key and dial i p 0.
l
SPKR LED flashes continuously.
l
Depress keys a a a
q
.
l
Depress the m key.
NOTE.
System messages can only be programmed
-19-