Panasonic Strata Se General Description Manual page 85

,
2. Enter the number of digits in the OCC Au-
thorization Code (00 - 99).
3. Caution: Do not program more digits than
required because toll restriction may be
defeated.
108 Program-Toll Restriction Override Code
#l
Registers the first of two codes that over-
ride toll restriction on outgoing calls.
l
Enter the four digits of the first toll restric-
tion override code.
109 Program-Toll Restriction Override Code
#2
Registers the second of two codes that over-
ride toll restriction on outgoing calls.
0 Enter the four digits of the second toll res-
triction override code.
1 X0 Program- Tol! Restriction Class Parame-
ters (X = 1 - 4)
This program defines parameters for each
class of toll restriction (X = 1 - 4). There are
four classes of toll restriction available on a
station-by-station basis. (See Program 6XX to
select the station class of toll restriction.) This
program is required only if 3- or 6-digit toll res-
triction is desired.
l
Mark an X next to the LED for each parame-
ter of each toll restriction class used.
02: All restricted area codes plus the office
cnde of 555 are aliowed, incltrding out-
of-area directory assistance calls (e.g.,
213 + 555 + 1212).
01 :I Overseas operator or unassisted over-
-
seas calls are to be restricted (01 /Ol 1).
00: Operator or operator-assisted calls are
used to be restricted (0).
1 XY Program-Toll Restriction
Class Area
Code Entry (X = Class 1 - 4) [Y = allow (2).
deny (3) or display (4)]
This program defines the area codes al-
lowed or denied for each toll restriction class.
This program is required only if 3- or 6-digit toll
restriction is desired. Each class area code table
can be defined as an allow (2) or deny (3) table.
Initialized data allows all area codes for each
class. All allowed area codes can be displayed
(4) for each class. For Toll Restriction Class 1,
-9-
PROGRAMMING PROCEDURES
SECTION 500-036-300
JANUARY 1988
enter all allowed area codes in the upper sec-
tion of the record sheet and all denied area
codes in the lower section. Make additional co-
pies of the record sheet for Toll Restrictlon
Classes 2, 3 and 4.
1 XZ Program- Toll Restriction Class Office
Code Entry (X = Class 1 - 4) [Z = allow (6).
deny (7) or display (8)]
This program defines the office codes al-
lowed or denied for each toil restriction class
within the home area code. Entry to this pro-
gram is required only if 3- or 6-digit toll restrlc-
tion is desired. Each class office code table can
be defined as an allow (6) or deny (7) table. In-
itialized data allows all office codes In the home
area code for each class. All allowed office
codes can be displayed (8) for each class. See
the detailed programming chart for office code
entry procedures.
2XY Program- Toll Restriction Area/Office
Code Exception Table
Entry to this program is required only if
6-digit (area/office code) toll restriction is de-
sired. There are eight area/office code excep-
tion tables available that are defined by X (1 -
8). Each table may have one area code and up
to 800 office codes entered. The area code is
entered when Y = 1 for each table, while office
codes are added
(Y = 2) or deleted (Y = 3) for
each table. All office codes in the table are dis-
played when Y = 4. Each area/office exception
table selected with Program 1X1 will be an ex-
ception (opposite) tc the allow (Program 1X2)
or deny (Program 1X3) area code table for each
toll restriction class. See the detailed program-
ming chart for area code and office code entry
procedures. The examples below are provided
for additional information.
1) Normal restriction for stations in Class 1 (al-
low all office codes within an area code).
l
Program 1XY is programmed to allow
(112) area code 213. Class 1 stations are
allowed to dial all office codes in area
code 213.
2) Area/office code exception (allow all office
codes within an area code except one) for sta-
tions in Class 1.
l
Program 1XY remains the same (112).
l
Program
1X1
has area/office code excep-
tion Table 1 (INT) selected (111).