Table of Contents
Advertisement
NOTE:
[f AROH
is available,
the CO will automati-
cally drop the lines when
the outside
party
hangs up. However,
if AROH is not available,
the person
who sets up the Trunk-to-Trunk
Connection
must
occasionally
monitor
the
call and disconnect
the CO lines when
the
two parties
hang
up.
0#6
Program-Trunk-to-Trunk
Connection
Enable
Selects
the CO lines to be used for trunk-
to-trunk
connections.
l
Mark
an X next to CO lines to be used for
trunk-to-trunk
connections.
07 Program-Automatic
Release
on Hold Tim-
ing
Selects
Cross Bar (XB) or ESS timing
for the
AROH
time
required
for the CO to open
line to
enable
call to be released
from
hold-XB
greater
than
95ms;
ESS greater
than
450ms.
(Has no
meaning
if AROH was rejected
in
Program
06.)
l
Mark an X next to each CO line that
requires
XB timing;
leave
blank
if ESS timing
is re-
quired.
0#7
Program-l
A2 Lnterface
l
Mark an X next to the CO
lines to be
bridged
with the lA2
system.
Leave blank if they will
not be bridged
with
the
lA2
system.
08 Program-CO
Line
Pickup
Groups
Informs
the svstem
of the CO lines that are
assigned
to aacn
group.
l
Mark
an X next to each
CO line that
is
to
belong
to Group
#2.
e
0#8
Program-
Night
Ringing
Over
External
Page*
"STRA TA Vle only
Selects
whether
or not a CO line rings
over
external
page.
(Has no meaning
if LED 02 was
not ON
in
Program
02.)
l
Mark an X next to the CO lines
that ring over
external
page.
09 Program-Single
CO Line (Dial
9) Group
Selection
Informs
the
system
of the
CO lines
that
PROGRAMMING
PROCEDURES
SECTION 500-036-300
JANUARY !!?I8
should
be considered
for selection
when
a sta-
tion
dials a. (Used
only
if LED 15 in
Program
01
is OFF.)
l
Mark
an X next to each
CO line that
is to
be
included
in the
"Dial
9" group.
09X
Program-
CO Line (Dial 91
- 98) Group
Assignments
Informs
the
system
of the
CO lines
that
should
be considered
for selection
when
a sta-
tion
dials a 0, a 1, a 3 a 3, J 3 3 1, 3 3 or 2 1.
(Used
only
if LED 15 in
Program
01
is ON.)
c,
l
Mark an X next to each CO line/trun
group
assignment.
0#9
Program-Off-Premises
Line Hunting
Selects
which
CO lines ring the device
con-
nected
to the "HUNT"
output
on the HOLB
op-
tion
module.
The "TEL"
output
always
rings.
1) With
no Off-Premises
Line Hunting
(LED off):
l
Call comes
into COl:
TEL1 and hunt
ring.
l
Call comes
into C02:
TEL2 rings, no hunt.
l
Call comes
into C03:
TEL3 rings, no hunt.
NOTE.
NIGHT mode has no effect
whenever
LED is
off.
2) Off-Premises
Line
Hunting
(LED on), Cot:
l
TEL1
rings
(DAY mode):
No hunt.
l
TEL1
rings
(NIGHT
mode):
Hunt
rings.
e TEL2
or 3 rings
(DAY mode):
No hunt.
l
TEL2 or 3 rings (NIGHT
mode):
Hunt rings.
190
Program-PBX
Backup
Assigns
CO lines to behind-PBX
operation.
The system
recognizes
PBX access codes on se-
lected
lines.
l
Mark an X next to each CO key/LED
that is
to be connected
to a PBX station
line.
19X
Program-
PBX Access
Codes
Assigns
codes that are used to access CO
lines
connected
to a PBX as determined
in
Program
190.
The system
recognizes
the ac-
cess codes and reacts appropriately
for Toll Res-
triction,
Automatic
Dialing
and
Repeat
Last
Number
Dialed.
l
Enter
the
actual
one-
or
two-digit
access
codes
(maximum:
8).
-7-
Advertisement
Chapters
Table of Contents
