Other Error Messages - Canon Pixma MP530 Service Manual

transmission of the procedure signal has been attempted the number of specified times but failed.
TX After transmitting EOR-MPS in ECM transmission, DCN has been received.
##777
TX After transmitting EOR-MPS in ECM transmission, re-transmission of the procedure signal has been
##778
attempted the number of specified times but failed, or T5 time-over (60 sec.) has occurred.
TX After transmitting EOR-MPS in ECM transmission, ERR has been received.
##779
TX After transmitting EOR-EOM in ECM transmission, no significant signal has been received, and re-
##780
transmission of the procedure signal has been attempted the number of specified times but failed.
TX After transmitting EOR-EOM in ECM transmission, DCN has been received.
##782
TX After transmitting EOR-EOM in ECM transmission, re-transmission of the procedure signal has been
##783
attempted the number of specified times but failed, or T5 time-over (60 sec.) has occurred.
TX After transmitting EOR-EOM in ECM transmission, ERR has been received.
##784
TX After transmitting EOR-EOP in ECM transmission, no significant signal has been received, and re-
##785
transmission of the procedure signal has been attempted the number of specified times but failed.
TX After transmitting EOR-EOP in ECM transmission, DCN has been received.
##787
TX After transmitting EOR-EOP in ECM transmission, re-transmission of the procedure signal has been
##788
attempted the number of specified times but failed, or T5 time-over (60 sec.) has occurred.
TX After transmitting EOR-EOP in ECM transmission, ERR has been received.
##789
RX After receiving EOR-EOP in ECM reception, ERR has been transmitted.
##790
TX / RX During the ECM mode procedure, a signal other than a significant one has been received.
##791
RX In ECM reception, PPS-NULL between partial pages has not been detected.
##792
RX During high-speed signal reception in ECM, no effective frame has been detected, and a time-over has
##793
occurred.

2-4. Other Error Messages

Message on the LCD
CANNOT SCAN FROM ADF
CHANGE PAPER TO
A4/LTR/LGL PLAIN
CHECK PRINTER
CLEAR DOC. [OK]
STOP DOC CLR [STOP]
DOCUMENT IN ADF
PRESS [OK]
COOLING HEAD
Cause
The document is loaded in the ADF when
applying <FIT-TO-PAGE> in [Enlarge/Reduce],
and <STICKER COPY> and <BORDERLESS
COPY> in <1.SPECIAL COPY>.
The paper size setting is set to a size other than
A4, letter or legal in fax receive mode.
The paper type setting is set to a type other than
PLAIN in fax receive mode.
An error requiring servicing might have occurred. Turn OFF the machine, and unplug the
Documents remain in the ADF.
The document is jammed in the ADF.
During printing, the Print Head may have become
too hot.
Load the document on the Platen Glass when
copying with <FIT-TO-PAGE> in
[Enlarge/Reduce], and <STICKER COPY>
and <BORDERLESS COPY> in
<1.SPECIAL COPY>.
Set the paper size setting to A4, letter or
legal and load paper of the same size.
Set the paper type setting to PLAIN.
power cord of the machine from the power
supply. After a while, plug the power cord of
the machine back in and turn ON the
machine. If the same error occurs, contact
Canon service representative.
Press [OK] to eject documents and press
[Stop/Reset] to stop ejecting.
To continue scanning, operate on the
application. The scanning from the ADF may
not be supported depending on an application
software.
Remove the document page jammed in the
ADF, then press [OK]. Operate again after
resolving the error.
Allow the machine to cool down. The
machine will resume printing when it has
1-11
Solution