Table of Contents
Advertisement
The following three Tele-File marks are available:
• OK: Place this mark when you decide the recorded
images are good.
• NG: Place this mark when you decide the recorded
images are not good.
• KP: Place this mark when it is hard to decide whether or
not the recorded images are good just after recording, or
when you want to insert a mark between multiple shots.
Recorded Tele-File marks are read by studio-use devices,
logging software, and so on, which support the Tele-File
function. These marks are very helpful for improving the
efficiency of tape editing.
Before recording a Tele-File mark
To use this function, the TELE-FILE MARK function
should be assigned to the ASSIGN 1 switch or TURBO
GAIN button.
For details, see "5-3-5 Assigning Functions to Assignable
Switches" on page 95.
Recording Tele-File marks
1
Start recording and set the camcorder to recording
pause mode by pushing the VTR START button or the
VTR button on the lens.
2
Push the ASSIGN 1 switch or the TURBO GAIN
button to which the TELE-FILE MARK function is
assigned.
The mark to be recorded appears on the viewfinder.
When you record a Tele-File mark for the first time
after you turn on the power of the camcorder, the mark
selected on the menu appears.
For details, see " Setting the Tele-File mark to be
recorded for the first time after power on" on page 53.
When OK is selected on the menu
This message disappears after 3 seconds. The mark
displayed when it disappears from the viewfinder is
recorded with the recording start time code.
Message
TELE-FILE MARK: OK
TELE-FILE MARK: NG
Meaning
States that an OK mark
has been recorded.
States that an NG mark
has been recorded.
Recording the Recording Start Time Code onto the Memory Label — Tele-File
Message
TELE-FILE MARK: KP
TELE-FILE MARK: ERASE
If the mark displayed on the viewfinder is different
from the desired one
Push the ASSIGN 1 switch several times while the
mark is displayed until the appropriate mark appears
on the viewfinder. The mark changes in the order of
OK t NG t KP t ERASE ....
If the display disappears before you select the
appropriate mark
Continue pushing the ASSIGN 1 switch until the
desired mark appears. If the desired mark disappears
from the viewfinder while that mark is displayed, the
mark recorded before will be overwritten and the mark
newly displayed is recorded.
Notes
• Tele-File marks are recorded only when they are
recorded using the ASSIGN 1 switch to which this
function has been assigned.
• Tele-File marks can be added only to the shot recorded
just before entering the rec pause mode.
When the message "INVALID OPERATION !"
appears
This message appears when you perform one of the
following misoperations:
• You push the ASSIGN 1 switch before the camcorder
enters the recording pause mode after loading the
cassette.
• If you turn off the power of the camcorder in recording
pause mode and then turn on the power again, the
camcorder is in the recording pause mode. Then, you
push the ASSIGN 1 switch in this situation.
• You push the ASSIGN 1 switch in a mode other than
recording pause mode.
Setting the Tele-File mark to be recorded
for the first time after power on
Using the menu, you can select the mark to be recorded in
the first recording pause mode when you press the
ASSIGN 1 switch after you turn on the power of the
camcorder.
Note
This menu setting allows the camcorder to display a mark
when you use the Tele-File mark for the first time after you
turn on the power of the camcorder. When you press the
ASSIGN 1 switch after that, the last selected mark appears.
Meaning
States that a KP mark
has been recorded.
States that the Tele-File
mark recorded on that
shot has been cancelled.
53
Advertisement
Table of Contents
