Sony HDW-790P Operation Manual page 152

No. Page
P05 BLACK GAMMA BLACK GAMMA
P06 KNEE 1
P07 KNEE 2
P08 DETAIL 1
P09 DETAIL 2
152
Menu List
Item Settings
OFF/ON
BLACK GAM RANGE LOW/L.MID/
H.MID/HIGH
MASTER BLK (–99 to 99)
GAMMA
R BLACK GAMMA (–99 to 99)
G BLACK GAMMA (–99 to 99)
B BLACK GAMMA (–99 to 99)
1) Y/R/G/B
OUTPUT SELECT
KNEE OFF/ON
KNEE POINT (M) 50.0 to 109.0
KNEE SLOPE (M) (–99 to 99)
KNEE SATURATION OFF/ON
KNEE SAT LEVEL (–99 to 99)
WHITE CLIP OFF/ON
WHITE CLIP LEVEL 100.0 to 109.5
KNEE SATURATION OFF/ON
KNEE POINT (R) –45.0 to 14.0
KNEE SLOPE (R) (–99 to 99)
KNEE POINT (G) –45.0 to 14.0
KNEE SLOPE (G) (–99 to 99)
KNEE POINT (B) –45.0 to 14.0
KNEE SLOPE (B) (–99 to 99)
DETAIL OFF/ON
APERTURE OFF/ON
DETAIL LEVEL (–99 to 99)
APERTURE LEVEL (–1 to 14)
DTL H/V RATIO (–99 to 99)
CRISPENING (–99 to 99)
LEVEL DEPEND OFF/ON
LEVEL DEPEND LVL (–99 to 99)
DETAIL FREQ (–99 to 99)
KNEE APERTURE OFF/ON
KNEE APT LEVEL (–99 to 99)
DTL WHT LIMIT (–99 to 99)
DTL BLK LIMIT (–99 to 99)
DTL V-BLK LMT (–99 to 99)
H/V CONTROL MODE H/V / V
Default Description
OFF Turns the black gamma correction on/off.
HIGH Sets the range affected by black gamma.
0 Adjusts the master black gamma.
0 Sets the correction curve of the R black
gamma.
0 Sets the correction curve of the G black
gamma.
0 Sets the correction curve of the B black
gamma.
Y Selects the output signal from the TEST OUT
connector, the input signal to the viewfinder,
and the output signal from the VBS/SDI
2)
OUT .
ON Turns the knee correction circuit on/off.
95.0 Sets the master knee point level.
0 Set the master knee slope level.
ON Turns the knee saturation function on/off.
0 Sets the knee saturation level.
ON Turns the white clipping function on/off.
3) Adjusts the white clipping level.
109.0
OFF Turns the knee saturation function on/off.
0.0 Sets the R knee point level.
0 Sets the R knee slope level.
00 Sets the G knee point level.
0 Sets the G knee slope level.
0.0 Sets the B knee point level.
0 Sets the B knee slope level.
ON Sets the detail correction function on/off.
ON Turns the aperture correction function on/off.
0 Sets the general level of the detail signal.
0 Sets the aperture level.
0 Sets the level of the V detail signal.
0 Sets the crispening level.
ON Turns the level depend function on/off.
0 Sets the level of the level depend function.
0 Sets the frequency of the H detail signal.
OFF Turns the knee aperture function on/off.
0 Sets the knee aperture level.
0 Sets the detail white limiter.
0 Sets the detail black limiter.
0 Sets the V detail black limiter.
V Select the operation mode of DETAIL H/V
RATIO on the DETAIL 1 page. (H/V: H and V
both enabled, V: V DTL only enabled)