GarrettCom Magnum 10KG Installation And User Manual
  1. Manuals
  2. Brands
  3. GarrettCom Manuals
  4. Switch
  5. Magnum 10KG
  6. Installation and user manual

GarrettCom Magnum 10KG Installation And User Manual

Managed switch with timing
Hide thumbs
Table of Contents

Advertisement

Quick Links

Magnum 10KG
Managed Switch
with Timing
Hardware
Installation and User Guide
www GarrettCom com
.
.

Advertisement

Table of Contents
loading

Related Manuals for GarrettCom Magnum 10KG

Summary of Contents for GarrettCom Magnum 10KG

  • Page 1 Magnum 10KG Managed Switch with Timing Hardware Installation and User Guide www GarrettCom com...
  • Page 2 If problems are experienced with Magnum 10KG Switch products, consult Section 6, Troubleshooting. Copyright © 2012 GarrettCom, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from GarrettCom, Inc. Printed in the United States of America GarrettCom, Inc.
  • Page 3 (i.e. 24VDC or 48VDC) and suitable rated output current. Product does not contain user replaceable fuses. Any internal fuses can ONLY be replaced by GarrettCom personnel through the RMA process. The chassis main earthing screw shall be connected to the supply protective earthing conductor.

  • Page 4: Table Of Contents

    INTRODUCTION ................... 11     Inspecting the Package and Product ............11     Product Description - Magnum 10KG Managed Switch ....... 12     Managed Network Software for Magnum 10KG ........13     Features and Benefits ................14  ...
  • Page 5 Magnum 10KG Managed Switch Installation and User Guide 07/12     5.1.11 10-2RJSFP, Two Gigabit RJ-45 or Two SFP (use in Slots A-D) ..39     TROUBLESHOOTING................40     Before Calling for Assistance..............40     When Calling for Assistance ..............41  ...

  • Page 6: Specifications

    Magnum 10KG Managed Switch Installation and User Guide 07/12 SPECIFICATIONS Technical Specifications Performance Filtering / Forwarding Rate: Ethernet (10Mb): 14,880 pps Fast Ethernet (100Mb): 148,800 pps Gigabit Ethernet (1000Mb): 1,488,000 pps Switching Processing Type: Store and Forward with IEEE 802.3x full-...
  • Page 7 Magnum 10KG Managed Switch Installation and User Guide 07/12 1000BASE-LX, full-duplex, multimode (50, 62.5μm cable) - 550m (1804 ft) 1000BASE-LX, full-duplex, singlemode (9μm cable) - 5km (16.4K ft) 1000BASE-ZX, full duplex, singlemode (9μm cable) - >70km (229.6K ft) Fiber Multimode connector types supported:...
  • Page 8 Magnum 10KG Managed Switch Installation and User Guide 07/12 DC Power Supply (Internal, floating ground) DC Power Connector: Terminal block (L) 24/48VDC Power Input (range 22 to 60VDC) (H) AC/DC Power Input (range 90-250V AC or DC) Standard 3-screw Terminal block: “ -, +, GND ”...

  • Page 9: Ordering Information

    Magnum 10KG Managed Switch Installation and User Guide 07/12 Ordering Information Hot-Swap Power supply models, w/Thermal Fins MODEL DESCRIPTION 10KG-HSPHH-TF: Magnum 10KG Managed Switch, front-mount, with two PS slots for two H Hot-Swap Power Supplies. May be factory-configured with a variety of fiber and copper port modules selected designed specifically for the 10KG-series.
  • Page 10 10KGR-H-TF: Same as Model 10KG-H-TF except chassis is a Reverse Mount unit. (All signal and power cables are in the rear) 10KG-HH-TF: Magnum 10KG Managed Switch, front-mount, with two integral 90- 250V AC/DC Power Supply. May be factory-configured with a variety of fiber and copper port modules selected designed specifically for the 10KG-series.
  • Page 11 (All signal and power cables are in the rear) 10KG-HH: Magnum 10KG Managed Switch, front-mount, with two integral 90-250V AC/DC Power Supply. May be factory-configured with a variety of fiber and copper port modules selected designed specifically for the 10KG-series. Configure up to 24 ports in a mix of Gb and 100Mb.

  • Page 12: Magnum 10Kg Managed Switch Installation And User Guide

    10KG-series. Configure up to 24 ports in a mix of Gb and 100Mb. 10KGPR-L: Same as Model 10KGP-L except chassis is a Reverse Mount unit. (All signal and power cables are in the rear) Please use this URL: for the complete Product bulletin for the Magnum 10KG. http://www.garrettcom.com/techsupport/hardware/datasheets/10kg_dscs.pdf www GarrettCom com...
  • Page 13 Magnum 10KG Managed Switch Installation and User Guide 07/12 “HSP” Hot-Swap power supply options: (If “HSP” base unit is selected, choose up to two power supply modules. For “-HF” or “-LF” models below, Also choose the KT-RFAN option in the Options & Extras...
  • Page 14 Magnum 10KG Managed Switch Installation and User Guide 07/12 10K4-SLCL Module w/four 100Mb “long-haul” singlemode fiber LC ports (40km) 10K4T-SLCL Module w/four 100Mb “long haul” singlemode fiber LC ports (40km) with 1588 timing 10K4-MTRJ Module w/four 100Mb multimode fiber MTRJ ports...
  • Page 15 Magnum 10KG Managed Switch Installation and User Guide 07/12 Options & Extras: KT-RFAN: Removable Fan for extra fiber ports and cooling; Optional for up to 16 fiber ports. Required for 18 to 36 fiber ports. CONSOLE-CBLQD: Console attachment cable. Serial null modem (aka X-modem) cable with RJ45 connector for the 10KG on one end and a DB-9 connector on other end.

  • Page 16: Introduction

    Magnum 10KG Managed Switch Installation and User Guide 07/12 INTRODUCTION Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier of any damage that you believe occurred during shipment or delivery.

  • Page 17: Product Description - Magnum 10Kg Managed Switch

    The swap-out can readily be done while the 10KG Switch continues in operation. The eight port configuration slots in the Magnum 10KG provide the flexibility for network designers to configure up to eight fiber or copper Gb ports and up to 16 100 Mb SFF fiber or copper ports.

  • Page 18: Managed Network Software For Magnum 10Kg

    Managed Network Software for Magnum 10KG The Magnum 10KG comes with licensed MNS-6K software or MNS-6K-SECURE, which allow the user to configure the Magnum 10KG as a Managed Switch and implements security features and other software-enabled features. (NOTE: Magnum 10KG managed switch will work with MNS-6K Rel v4.4.1 firmware or higher version only, or MNS-6K-SECURE v14.4.1 firmware or higher...

  • Page 19: Features And Benefits

    10KGP base units support up to 16 ports of 802.3at PoE+ ports. Managed switching for high performance Ethernet LANs Magnum 10KG Switches provide non-blocking (all ports can run at full speed at once) performance with standard Managed Network Software. Switching services includes 802.1p QoS packet prioritization The Magnum 10KG switching hardware supports QoS, giving packet processing priority to priority tagged packets according to the IEEE 802.1p 4-level standard.
  • Page 20 Magnum 10KG Managed Switch Installation and User Guide 07/12 MNS-6K-SECURE (optional, for extra security) Magnum MNS-6K-SECURE software is designed for those customers demanding extra security in their networks. MNS-6K-SECURE is an optional item--licensed per switch. All of the features in regular MNS-6K are included, plus extra security.

  • Page 21: Installation

    5.) If the equipment is mounted in an enclosed or multiple rack assembly, verify that the equipment has a reliable and uncompromised earthing path. This section describes installation of the Magnum 10KG Switch, as well as connection of the various Ethernet media types.

  • Page 22: Connecting Ethernet Media

    Connecting Twisted Pair (CAT3, CAT5, UTP or STP) 3.2.1 The RJ-45 ports of the Magnum 10KG can be connected to the following two media types: 100BASE-TX and 10BASE-T. CAT 5 cables should be used when making 100BASE-TX connections. When the ports are used as 10BASE-T ports, CAT 3 may be used.

  • Page 23: Connecting Twisted Pair (Cat5E Or Better, Utp Or Stp)

    Connecting Twisted Pair (CAT5e or better, UTP or STP) 3.2.2 The RJ-45 Gigabit ports (Slots A,B,C and D) of the Magnum 10KG can be connected to the media types, 1000BASE-T or CAT 5E or better 100-ohm UTP or shielded twisted pair (STP) balanced cable. The CAT 5E or better 100-ohm UTP or shielded twisted pair (STP) balanced cable is recommended to use when making 1000BASE-TX connections.

  • Page 24: Sfp (Small Form-Factor Pluggable) Transceivers

    The Magnum 10KG is designed for industry- standard SFPs for user selection of the SFP media type as desired. All SFPs used in the Magnum 10KG are compliant with the industry standard Multi- Source Agreement (MSA) ensuring compatibility with a wide range of networking kit.

  • Page 25: Rack-Mounting Options

    3.3.1 Rack-mounting options Installation of the Magnum 10KG Switch in a 19” rack is a simple procedure. The units are 1.5U (2.63”) high for Thermal fin version and 1U (1.74”) high for non- Thermal fin version. When properly installed, the front-mounted LED status indicators should be in plain view and easy to read.
  • Page 26 Magnum 10KG Managed Switch Installation and User Guide 07/12 model without Thermal Fin cover model with Thermal Fin cover Fig 3.3a 10KG Front mount dimensions www GarrettCom com...
  • Page 27 Magnum 10KG Managed Switch Installation and User Guide 07/12 model without Thermal Fin cover model with Thermal Fin cover Fig 3.3b 10KG Reverse mount dimensions www GarrettCom com...

  • Page 28: Powering The Magnum 10Kg Managed Switch

    Magnum 10KG Managed Switch Installation and User Guide 07/12 Powering the Magnum 10KG Managed Switch The Magnum 10KG Switch is available with the choice of Dual Hot- Swappable power supplies, single fixed (non Hot-Swappable) and Dual Fixed internal power supplies.

  • Page 29: Alarm Contacts For Monitoring Internal Power And Software Traps

    Pin 4 Alarm Contacts for monitoring internal power and Software Traps The Alarm Contacts feature, standard on the Magnum 10KG, provides two Form C Normally Closed (NC) contacts to which the user can attach two sets of status monitoring wires at the Alarms terminal block, see Fig 3.5a below.
  • Page 30 Magnum 10KG Managed Switch Installation and User Guide 07/12 The Alarm Contacts are located to the left of the power input connection of the Magnum 10KG unit and are green in color as shown in the picture. Alarm contact ratings (resistive): 220 VDC / 0.27A - 60W...

  • Page 31: Connecting The Console Terminal To Magnum 10Kg

    Note: For a detailed description of Managed Network Software (MNS-6K) and Magnum 10KG Switch software configuration for Network Management, please refer to Magnum 6K Software Manual available on GarrettCom‘s FTP site. Also available on GarrettCom’s website at: http://www.garrettcom.com/techsupport/sw_downloads.htm...

  • Page 32: Operation

    100/1000Mbs separate traffic domains for fiber ports to maximize bandwidth utilization and network performance. All ports can communicate to all other ports in a Magnum 10KG, but local traffic on a port will not consume any of the bandwidth on any other port.

  • Page 33: Auto-Cross (Mdix) And Auto-Negotiation, For Rj-45 Ports

    07/12 Address Learning All Magnum 10KG units have address table capacities of 8K node addresses suitable for use in larger networks. They are self-learning, so as nodes are added, removed or moved from one segment to another, the 10KG Switch automatically keeps up with node locations.

  • Page 34: Flow-Control, Ieee 802.3X Standard

    The Path Delay Value (PDV) bit-times must account for all devices and cable lengths within that domain. For Magnum 10KG Fast Ethernet switched ports operating at 100Mb half-duplex, the bit time delay is 50BT.

  • Page 35: Packet Prioritization, 802.1P Qos

    As a LAN device, the Magnum 10KG can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and internal switch buffers.

  • Page 36: Power Budget Calculations For 10Kg Modules With Fiber Media

    An important feature of the Magnum 10KG is the use of Port Modules for flexible mixed-media connectivity to RJ-45 copper and various fiber media. The first four slots (A, B, C, D) of the Magnum 10KG Switch are fixed RJ-45 auto-negotiating copper ports and SFP (Small Form Pluggable) fiber ports with 1000Mbps capability.

  • Page 37: 10Kg Module Led Designations

    Magnum 10KG Managed Switch Installation and User Guide 07/12 5.1.1 10KG Module LED designations All ports have the following LED designations: L/A = Link / Activity Off (No Link established) ON (Link established) BLINKING (Link Activity) F/H = Full Duplex / Half Duplex (for Copper ports)

  • Page 38: 10K4-Rj45, Four 10/100Mb Rj45 Ports (Use In Slots E-H)

    Magnum 10KG Managed Switch Installation and User Guide 07/12 5.1.2 10K4-RJ45, four 10/100Mb RJ45 ports (use in Slots E-H) The 10K4-RJ45 four-port copper module provides four 10/100Mb switched RJ- 45 ports. The 10/100Mb switched ports normally (as a default setting) are independently N-way auto-negotiating and auto-crossover (MDIX) for operation at 10 or 100Mb speed in full- or half-duplex mode.

  • Page 39: 10K4Px-Rj45, Four 10/100Mb Poe+ Rj45 Ports (Use In Slots E

    Magnum 10KG Managed Switch Installation and User Guide 07/12 5.1.3 10K4PX-RJ45, four 10/100Mb PoE+ RJ45 ports (use in Slots E-H) The 10K4PX-RJ45 four-port copper module provides four 10/100Mb switched RJ-45 ports with PoE 802.3at support. The 10/100Mb switched ports normally (as a default setting) are independently N-way auto-negotiating and auto-crossover (MDIX) for operation at 10 or 100Mb speed in full- or half-duplex mode.

  • Page 40: 10K4-Mlc, Four Multimode Lc (Use In Slots E-H)

    The 10K4-MLC fiber ports are Small Form Factor (SFF) LC Multimode connectors used primarily in 100Mbps fiber-to-IED links in industrial applications. When installed in a Magnum 10Kg Series Switch, it supports fiber optic cable distances up to the IEEE-standard 100Mbps distance limits, i.e., typically 2km at full-duplex and 412m at half-duplex.

  • Page 41: 10K4-Mtrj, Four Multimode Mtrj (Use In Slots E-H)

    Magnum 10KG Managed Switch Installation and User Guide 07/12 5.1.6 10K4-MTRJ, four Multimode MTRJ (use in Slots E-H) The 10K4-MTRJ four-port fiber module provides four 100Mb Multimode MTRJ Fiber ports. The 10K4-MTRJ fiber port is a Small Form Factor (SFF) MTRJ Multimode connector.

  • Page 42: 10K2-Msc, 10K2-Mst (Use In Slots E-H)

    Magnum 10KG Managed Switch Installation and User Guide 07/12 5.1.7 10K2-MSC, 10K2-MST (use in Slots E-H) Two SC Multimode or two ST Multimode Upper Port module (Slots E, G) Lower Port module (Slots F, H) The 10K2-MSC (shown) two-port fiber module provides two 100Mb Multimode SC Fiber ports.

  • Page 43: 10K2-Ssc, 10K2-Sscl, 10K2-Sst (Use In Slots E-H)

    Magnum 10KG Managed Switch Installation and User Guide 07/12 5.1.8 10K2-SSC, 10K2-SSCL, 10K2-SST (use in Slots E-H) Two SC Singlemode or two ST Singlemode The 10K2-SSC two-port fiber module provides two 100Mb Singlemode SC Fiber ports, supporting distances up to 20km. This module provides the same functions as the Multimode version (see Section 5.1.7 for more details).

  • Page 44: 10K2-F10St, Two 10Mb St Multimode (Use In Slots E-H)

    Magnum 10KG Managed Switch Installation and User Guide 07/12 5.1.10 10K2-F10ST, Two 10Mb ST Multimode (use in Slots E-H) Upper Port module (Slots E, G) Lower Port module (Slots F, H) The 10K2-F10ST two-port fiber module provides two 10Mb Multimode ST Fiber ports.

  • Page 45: Troubleshooting

    However, if you are unsure of the procedures described in this section or if the Magnum 10KG Switch is not performing as expected, do not attempt to repair the unit; instead contact your supplier for assistance or contact GarrettCom Customer Support.

  • Page 46: When Calling For Assistance

    Date of installation Failure symptoms, including a full description of the problem. GarrettCom will carefully test and evaluate all returned products, will repair products that are under warranty at no charge, and will return the warranty-repaired units to the sender with shipping charges prepaid (see Warranty Information, Appendix A, for complete details).

  • Page 47: Shipping And Packaging Information

    Magnum 10KG Managed Switch Installation and User Guide 07/12 Shipping and Packaging Information Should you need to ship the unit back to GarrettCom, please follow these instructions: Package the unit carefully. It is recommended that you use the original container if available. Units should be wrapped in a "bubble-wrap" plastic sheet or bag for shipping protection.

  • Page 48: Appendix A: Dc Power Input

    07/12 APPENDIX A: DC Power Input A1.0 Specifications for Magnum 10KG Switches, DC Power at 24/48VDC and 90-250 AC/DC Power input Each Magnum Model 10KG Managed Switch requires DC power input, at 24/48VDC and 90-250 AC/DC nominal. The wide range of DC power input types qualifies this product for use in 24/48VDC and 90-250 AC/DC applications in different industries.
  • Page 49 Magnum 10KG Switch. The DC terminal block on the Magnum 10KG Managed Switch is located on the right rear or left front (Reverse unit) of the unit and is equipped with four (6) screw-down lead posts. The power terminals are identified as positive (+/L) and negative (-/N), and they are electrically floating inside the unit so that either may be grounded by the user if desired.
  • Page 50 Magnum 10KG Managed Switch Installation and User Guide 07/12 A3.1 UL Requirements for DC-powered units CAUTION: 48VDC products shall be installed with a readily accessible disconnect device in the building installation supply circuit to the product. Minimum 18AWG cable for connection to a Centralized DC power source.

  • Page 51: Appendix B: Removal / Installation Of The Hot-Swap Power Supply

    Magnum 10KG Managed Switch Installation and User Guide 07/12 APPENDIX B: Removal / Installation of the Hot-Swap power supply Tools Required: #1 Phillips head screwdriver Step 1: Locate the Hot-Swap power supply locking screw. Loosen the locking screw until no longer engaged.

Table of Contents