Related Manuals for GarrettCom Magnum 6K32T
Summary of Contents for GarrettCom Magnum 6K32T
-
Page 1: Managed Switch
Magnum 6K32T & 6K32TRC 6K32T 6K32TRC Managed Switch Installation and User Guide Hardware User Manual www GarrettCom com $5.00 USD... - Page 2 If problems are experienced with Magnum 6K32T & 6K32TRC Switch products, consult Section 6, Troubleshooting, of this User Guide. Copyright © 2007 GarrettCom, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from GarrettCom, Inc.
- Page 3 Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed GarrettCom, Inc. below: 47823Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com...
-
Page 4: Table Of Contents
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) TABLE OF CONTENTS... SPECIFICATIONS ... 2 Technical Specifications... 2 Ordering Information ... 5 INTRODUCTION... 9 Inspecting the Package and Product... 9 Product Description - Magnum 6K32TRC Managed Switch... 10 2.2.1a Magnum 6K32T Managed Switch Chassis ... - Page 5 Rev B 12/05 : Updated Gigabit options Rev A 05/05 : Minor updates, Auto-Cross(MDIX) Rev A 02/05 : Minor updates and tweak on LC connector diagram Rev A 08/04 : This revision is the initial release of the 6K32T manual. www GarrettCom com ... 54 ...
- Page 6 Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) The Magnum Line INDUSTRIAL NETWORKING PRODUCTS "DESIGNED AND MANUFACTURED IN THE USA" OVERVIEW GarrettCom, Inc. offers premium-quality Magnum™ line INDUSTRIAL conectivity products with industry-standard functionality and built-in fiber configurability. Magnum products are designed for use in demanding Industrial Grade, Carrier Class, POWER UTILITY and OEM applications where reliability is a primary consideration.
-
Page 7: Specifications
Magnum 6K32T & 6K32TRC Managed Switch SPECIFICATIONS Technical Specifications Performance Filtering / Forwarding Rate: Ethernet:14,880 pps Fast Ethernet: 148,800 pps Gigabit Ethernet: 1,488,000 pps Switching Processing Type: Store and Forward with IEEE 802.3x full- duplex flow -control, non-blocking Data Rate: 10Mbps,100Mbps and 1000Mbps... - Page 8 100/10: ON = 100Mbps speed OFF = 10 Mbps Operating Environment UL 60950 “Component Parts” temp. ratings: 130° F (55°C) (6K32T) UL 60950 “Component Parts” temp. ratings: 140° F (60°C) (6K32TRC) IEC 60068 “Type Test” ratings:- -40°to 185°F (-40°to 85°C) Ambient Relative Humidity: 5% to 95% (non-condensing) Altitude: -200 to 13,000 ft.
- Page 9 See also Note for Power Substations in Section 3.2.4, 3.6.1, and 5.2.9 IEC61850 EMC and Operating Conditions Class C for Power Substations Warranty: Three years, return to factory For a Configuration Guide, see the GarrettCom web site at http://www.garrettcom.com/techsupport/insertion_guides/6k32trcg.pdf http://www.garrettcom.com/techsupport/insertion_guides/6k32trccg.pdf (6K32TRC) mktg@GarrettCom.com...
-
Page 10: Ordering Information
Magnum Managed Switch MODEL DESCRIPTION Magnum 6K32T 16 10/100 RJ-45 ports managed switch with two optional port modules (6K32T) which may be configured with a selection of 10/100/1000Mb fiber and copper connector types, max. 32 ports Magnum 6K32T-48VDC:Same as 6K32T except power input is –48VDC... - Page 11 6KP2-2GCU two-port in one slot Gigabit 6K module, uses one 6K slot and provides two Gb Copper (1000BASE-RJ45 Auto-negotiating) ports. (includes front–panel metal sheet). 6KM-BLNK Blank cover for one 6K32T & 6K32TRC module slot opening in a Magnum 6K32T & 6K32TRC chassis CONSOLE CBL Industry standard serial cable, DB-9 connectors for RS-232 “...
- Page 12 Installation and User Guide 05/07) 6K32T/6K32TRC PoE Modules with 48VDC Pass-Through Configuration options: only one A or B module slot of 6K-Series switch with 48VDC power input may be configured with a PoE Modules New P6KP8-RJ45 8 port PoE module for 6ks with 48vdc PS, w/eight PoE power source 10/100 auto-negotiating auto cross RJ-45 ports.
- Page 13 New PI6KP6-RJ10ST “4+2” port PoE module for 6ks with 48vdc PS, w/four POE power source and two 10 Mb 2km sm FL ST connectors GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice. www GarrettCom com...
-
Page 14: Introduction
Inspect the contents of this package for any signs of damage and ensure that the items listed below are included. This package should contain: Magnum 6K32T, 6K32TR or 6K32TRC Managed Switch, base unit (configured with user-selected port module option in modular slot) AC Power Cord (U.S. and other 115 VAC only) Set of metal “Ears”... -
Page 15: Product Description - Magnum 6K32Trc Managed Switch
Ethernet solutions with 16 10/100 RJ-45 ports fixed and two modular configuration slots. The two modular configurable slots of the Magnum 6K32T offer the flexibility to configure up to sixteen 100Mb, (RJ-45 and 16 fiber ports) or a maximum of four Gigabit(1000Mb) options to handle high bandwidth application efficiently. - Page 16 Magnum 6K32T & 6K32TRC Managed Switch LANs, it offers S-ring, RS-Ring, Link-Loss-Learn, STP and RSTP. Security features include SNMPv3, SSL/SSH, 802.1X, TACACS+, Port Security, and Tagged VLANs and a secured user friendly web based option. The IGMP feature for multicast traffic and streaming video application and IGMP-L2 mode feature is an attempt to provide a Layer 3 solution with 6K-Switches effectively and economically.
-
Page 17: Magnum 6K32T Managed Switch Chassis
Ethernet requirement with cost-effective secure solutions. The Magnum 6K32T is also available in a Reverse model option, where the LEDs are on the front and the available ports along with the power supply area found on the rear side. -
Page 18: Eight-Port Sff Fiber Modules (6K8-Mtrj, 6K8-Mlc)
Ethernet media requirements. Evolving mixed-media requirements for 10Mb and 100Mb fiber, copper, and Gigabit ports can be easily handled by the Magnum 6K32T & 6K32TRC product reliably The packaging and power-input options target the Magnum 6K32T &... -
Page 19: Eight-Port Copper Module, 6K8-Rj45 (Mdix)
Using the 6K32T & 6K32TRC’s MNS software, the user may select full- or half-duplex mode per-port through the set-up of the software (See the Magnum 6K32T & 6K32TRC MNS Software Manual for the flexibility to adapt to any FDX or HDX type of Fast Ethernet devices). -
Page 20: New Poe(Power Inside), Pi6Kp8-45Rj (Mdix), 8-Port 10/100Mb
Magnum 6K32T & 6K32TRC Managed Switch On the model 6K8-RJ45 module, there are four LEDs for each port, two in the connector and two separate. The LK (Link) LED indicates “ready for operation” on that port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port when lit. -
Page 21: New Poe(Power Pass-Through) P6Kp8-Rj45 (Mdix) 8-Port
Magnum 6K32T & 6K32TRC Managed Switch PoE LED is ON when connected properly to a 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE. -
Page 22: Four-Port 10 Mb Mm Fiber St Modules
Magnum 6K32T & 6K32TRC Switch to connect to any 10Mb hub or media converter or almost any other device with a 10Mb fiber Ethernet port. User mode control per port through the MNS software is the same as the other 6K32T & www GarrettCom com... -
Page 23: Gigabit (1000Mbps) Port Modules
The Magnum 6K32T & 6K32TRC & 6K32’s offer wide options for Gigabit speed with multiple choices for the modular slot. The new Magnum 6K32T & 6K32TRC can be configured with four Gigabit ports (copper or Fiber) maximum. The Gigabit port option for the modular slot comes in a couple of different configurations. -
Page 24: Packet Prioritization, 802.1P Qos
Quality of Service means providing consistent predictable data delivery to users from datagram paths that go all across a network. As a LAN device, the Magnum 6K32T & 6K32TRC can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and buffers. -
Page 25: Managed Network Software 6K32T & 6K32Trc
Magnum 6K32T & 6K32TRC Managed Switch Another feature implemented in Magnum 6K32T & 6K32TRC Switches is a collision-based flow-control mechanism (when operating half-duplex only). When the Switch detects that its free buffer queue space is low, the Switch prevents more frames from entering by forcing a collision signal on all receiving half-duplex ports to stop incoming traffic. -
Page 26: Features And Benefits
Modular design for port flexibility, in a 1U space-saving rack-mount package The 1U Magnum 6K32T & 6K32TRC chassis has 1 slot for port configurations. A family of 2, 4, 6 or 8 port modules allows the user to select the desired mix of port types and speeds. -
Page 27: Applications
The performance characteristic of the 6K32T & 6K32TRC Switches enables them to inter-connect a series of subnets (one subnet per 6K32T Switch port) in a LAN traffic center. The subnet connections may be via fiber or twisted pair cabling, 100Mbps or 10 Mbps speed, and full-or half-duplex mode. - Page 28 LANs; Port-based VLANs and Tag-based VLANs. In an office environment where departments such as Finance, Engineering, R&D, and Marketing need to each keep a secure LAN, the 6K32T’s VLAN feature will prevent traffic cross-over among traffic domains and thus keep sensitive data and information controlled.
- Page 29 48VDC input power option with Dual Source is especially useful in telecom central offices. The Magnum 6K32T with two Gigabit ports in the modular slot allows it to connect into a Gigabit mesh structure with an RSTP and S-Ring combination used in a no-single-point-of-failure self-healing LAN topology along with a ring of multiple 6K25s at the edge to allow the system to efficiently recover from a fault in the network.
- Page 30 Magnum 6K32T & 6K32TRC Managed Switch 10/ 1 00 F/ H 10/100 LK/ACT F/ H 10/100 LK/ACT 10/100 LK/ACT 10/100 LK/ACT 10/100 LK/ACT 6K32TRC in a Redundant application Example 4: In a “ (video+data)” application where a network being designed to catered the need of multicast streaming and broadcast traffic of higher bandwidth to provide a video conferencing and video in demand channel option to the user.
- Page 31 Magnum 6K32T & 6K32TRC Managed Switch Equipped with IGMP-L2 mode enhanced features allow the Magnum 6K32TRC to meet the fastest growing application of video monitoring or video surveillance demand of industry and provide an economical and effective solution to meet that expectation.
-
Page 32: Installation
If the equipment is mounted in an enclosed or multiple rack assembly, the environmental temperature around the equipment must be less than or equal to 55C FOR 6K32T and 60C for 6K32TRC. If the equipment is mounted in an enclosed or multiple rack assembly, adequate airflow must be maintained for proper and safe operation. -
Page 33: Connecting Ethernet Media
Connecting Fiber Optic ST-type, “twist-lock” The following procedure applies to installations using a PM with ST-type fiber connectors. This procedure applies to ports using a 6K32T & 6K32TRC module, MST-type port. Before connecting the fiber optic cable, remove the protective dust caps from the tips of the connectors on the PM. -
Page 34: Connecting Fiber Optic Sc-Type, "Snap-In
3.2.4 Connecting Twisted Pair (RJ-45,CAT3, CAT5, Unshielded or Shielded) The RJ-45 ports of the Magnum 6K32T & 6K32TRC can be connected to the following two media types: 100BASE-TX and 10BASE-T. CAT 5 cables should be used when making 100BASE-TX connections. When the ports are used as 10BASE-T ports, CAT 3 may be used. -
Page 35: Connecting Twisted Pair (Cat-5E Or Better)
3.2.5 Connecting Twisted Pair (CAT-5e or better, Unshielded or Shielded) The RJ-45 1000BASE-TX Gigabit ports of the Magnum 6K32T & 6K32TRC can be connected via copper media with the following minimum specifications; 1000BASE-T, CAT-5e, or for better results, 100-ohm UTP shielded twisted pair (STP) balanced cable. - Page 36 Magnum 6K32T & 6K32TRC Managed Switch to its compact, hot pluggable characteristics, SFPs are becoming a very popular choice for various applications. The small-chassis Magnum 6K is designed for industry-standard Gb-SFPs and Gb-SFPCU (copper) for user selection of the SFP gigabit media type as desired.
-
Page 37: Power Budget Calculations 6K32T & 6K32Trc Pm's
Magnum 6K32T & 6K32TRC Managed Switch The various SFPs transceivers supported by GarrettCom 6KQs D slot are- Module Model# Gigabit Gb Modules, fixed ports--SFP (Small Form Factor) 6KP2-2GSFP 2 SFP 6KP2-1GSFP1CU 1SFP 1 CU 6KP1-1SFP 1SFP 6KP1-1GCU 1 CU Gb SFP fiber optic transceivers... - Page 38 Magnum 6K32T & 6K32TRC Managed Switch and the “Cable Loss” for 100/140 (Multi-mode) is 3.3 dB/km, and the “Cable Loss” for 9/125 (Single-mode) is 0.5 dB/km and the “Cable Loss” for 9/125 (Single-mode) is 0.4 dB/km (LXSC25) and the “Cable Loss” for 9/125 (Single-mode) is 0.25 dB/km(LXSC40) and the “Cable Loss”...
-
Page 39: Rack-Mounting (For 19" Retma)6K32T & 6K32Trc's
Rack-mounting (for 19” RETMA racks), Magnum 6K32T & 6K32TRC’s Installation of a Magnum 6K32T & 6K32TRC Fiber Switch in a 19” rack is a simple procedure. The units are 1U (1.70”) high. When properly installed, the front- mounted LED status indicators should be in plain view and easy to read. -
Page 40: 3.3.2 Rack-Mounting, Reverse Version Of The Magnum 6K32T's
Magnum 6K32T & 6K32TRC Managed Switch the Magnum 6K32T & 6K32TRC Switches. These brackets are popular in the Telco industry where they are a standard for Central Office rack-mounting purposes. The 23” and the ETSI brackets are mainly used for larger equipment These brackets are rack-mounted in a frame typically accessed in operation from both sides. -
Page 41: Powering The Magnum 6K32T & 6K32Trc Managed Switch
Alarm Contacts is part of the Power Input panel in the Magnum 6K32T & 6K32TRC case. The AC or DC power input connection is in the same panel. A manual On-Off Switch for power to the unit is not available on 6K32T & 6K32TRC units with the Alarm Contacts option, as these two features occupy the same space in the case. -
Page 42: 6K32T & 6K32Trc Port Module (6Kpm) Installation
The second (bottom position) NC Alarm Contact is held close when there is power on the main board inside of the 6K32T & 6K32TRC. This provides a “Hardware Alarm” because the NC contacts will open when internal power is lost, either from an external power down condition or by the failure of the power supply inside of the Magnum 6K32T &... - Page 43 Step 2. Remove Chassis Cover The Magnum 6K32T & 6K32TRC chassis are combined with top, bottom and front panel parts and assembled together with the help of 17 Philips-head screws. There are 5 screws located on the front-bottom and 3 at rear-top of the unit and one each on the front and rear sides.
- Page 44 Fig 3.5.1b: Pulling out the top coved from the chassis base Caution: Be careful not to disturb the power supply. Looking down into the Magnum 6K32T & 6K32TRC unit, notice that there are individual PM installation spaces and female latch (white) connectors provided on the far right side of main board along with four stand-off’s for 6KPM card position.
-
Page 45: Installing 6Kpm Cards In The 6K32T & 6K32Trc
Placed Granddaughter board (as shown in fig. 3.5.2a and 3.5.2b) on the chassis built in stand off (female) provided at the front of the 6K32T & 6K32TRC Main Board and screw down tightly with the three 5/16 stand-off (male) on the top of the Granddaughter board The 5/16 stand off has been used to place the daughter board on the top of the granddaughter board and latch it securely. - Page 46 Magnum 6K32T & 6K32TRC Managed Switch Step 3. The figure here illustrates the basic layout of an individual PM card. 6KPM card fits into the space provided on the main board over the grand-daughter Bd. and the male latched cream color connector( as shown in above fig. with arrow mark).
- Page 47 Magnum 6K32T & 6K32TRC Managed Switch 6K8-BLNK) to cover the slot opening in the front panel. This will maintain proper cooling air flow, safety, and operation as required by FCC, CE, and other regulations. Step 6. Now screw down the daughter board with 7 #440 screws except the last two at the end, so that it holds the daughter board securely.
-
Page 48: Removing 6Kpm Cards
12 screws as being mentioned earlier. 3.5.3 Removing 6KPM Cards To properly remove a 6KPM card from the 6K32T & 6K32TRC Managed Switch, follow the 3 steps below. Step 1. Remove chassis cover Caution: Be sure the power cord is unplugged. -
Page 49: Connecting The Console Terminal To 6K32T & 6K32Trc
(Management) Use a DB-9 “null modem” cable to connect the Magnum 6K32T & 6K32TRC Console Port (the RS-232 port on the 6K32T & 6K32TRC Switch) to the your PC, so that your PC becomes the 6K32T & 6K32TRC’s Console Terminal. -
Page 50: Rs-232 (Db-9) Console Com Port (Serial Port) Pin
The above provided information enables a managed station( a PC or Console terminal) to connect directly to the switch using a straight through cable. Note: For using Console port to configure the managed switch, a serial (Null-modem) female to female cable is required to communicate properly. The Null-Modem (DB-9) -
Page 51: Operation
10 or 100Mb separate traffic domains for fiber ports to maximize bandwidth utilization and network performance. All ports can communicate to all other ports in a Magnum 6K32T & 6K32TRC, but local traffic on a port will not consume any of the bandwidth on any other port. -
Page 52: Status Leds
Section 7 (Port Setup) of Magnum 6K32T & 6K32TRC Software user guide (MNS-6K) . One frequently-used application for the Managed 6K32T & 6K32TRC Switch copper ports is to connect one of them using a fiber media converter to another Switch in the network backbone, or to some other remote 100Mb device. - Page 53 “highest order mode” result can change at any time depending on network changes that may occur). If the device at the other end is not an auto-negotiating device, the 6K32T & 6K32TRC’s www GarrettCom com...
-
Page 54: Flow-Control, Ieee 802.3X Standard
The Path Delay Value (PDV) bit-times must account for all devices and cable lengths within that domain. For Magnum 6K32T & 6K32TRC Fast Ethernet switched ports operating at 100Mb half-duplex, the bit time delay is 50BT. -
Page 55: Inspecting The Package And Product
6 or 8-port interfaces are designed to support all standard Ethernet media types at 10 or 100Mps speed. Each 6K32T & 6K32TRC PM can provide two, four, six or eight ports for connecting Ethernet segments with its individual connector type and media. -
Page 56: 6Kp6-Rjmst Multi-Mode Fx-St "Twist Lock" Module
100Mb combo module with the exception of 10Mb speed at the ST fiber module. The ST-connector functions as a fiber optic transceiver to support 10BASE-FX network segments. When installed in a Magnum 6K32T & 6K32TRC Managed Switch, the copper port supports the standard distance 100m on each port and the fiber port supports fiber optic cable distances up the IEEE-standard 10Mbps distance limits, i.e., typically... -
Page 57: 1B 6Kp4-F10St Multi-Mode Fx-St "Twist Lock" Module
Magnum 6K32T & 6K32TRC switch. They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports. It supports distances according to the 10Base-FL standard i.e, 2Km distance for multi-mode fiber. (Single-mode for 10Km distance may be available as a special order). -
Page 58: 6Kp6-Rjmsc Multi-Mode Fx-Sc "Snap-In" Fiber Connector
Full duplex for the 100Mb fiber. The 10Mb ST-fiber ports allow the user to connect their legacy 10Mb network to the Magnum 6K32T & 6K32TRC switch. They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports. -
Page 59: 6Kp6-Rjssc Mbps Single-Mode Fx-Sc-Type, "Snap-In
SC-type connectors. It provides an advantage through combining copper and Fiber functions in one module of the 6K32T & 6K32TRC Switch supporting four Copper and two single-mode fiber network segments. The 6KP6-RJSSC, when installed in a Magnum 6K32T & 6K32TRC Switch operates on copper at the 100m distance. -
Page 60: 4A 6Kp6-Rj10St Fl-St-Type, "Twist-Lock" Connector
The Magnum 6KP6-RJ10ST is also a Combo module equipped with 4 dual speed copper ports and 2 multi-mode 10 Mb fiber ST-type connectors. It provides a combination of copper and Fiber functions in one module to the 6K32T & 6K32TRC Switches, supporting four Copper and two 10Mb of ST fiber network segments. -
Page 61: 5A 6Kp6-Mt10Stmode Fx Factor
100Mb full-duplex, whereas the bottom two ports multi-mode ST-Fiber support 10Mb half-duplex. This combo module provides more flexibility to the user to connect their legacy 10Mb fiber as well as 100Mb to the Magnum 6K32T & 6K32TRC Switch. When installed in a Magnum 6K32T & 6K32TRC Switch, the 100Mb MTRJ connector supports fiber optic cable distances up to the IEEE-standard 100Mbps distance limits, i.e., typically 2km at full-duplex and 412m at half-duplex. -
Page 62: 6Kp8-Mlc Lc Connector Small
LC connector “small-form-factor” used primarily in 100Mbps fiber-to-the- desktop links. When installed in a Magnum 6K32T & 6K32TRC Switch, it supports fiber optic cable distances up to the IEEE-standard 100Mbps distance limits, i.e., typically 2km at full-duplex and 412m at half-duplex. -
Page 63: 6Kp8-45Lc 10/100 Mbps Rj-45 Connector
4 10/100 RJ-45 ports and 4 LC( Small form factor) multi-mode fiber ports. When installed in a Magnum 6K32T & 6K32TRC Switch, it supports the standard distances as per mentioned on 5.2.8. and the LEDs also acts similarly as mentioned above. -
Page 64: 10A. New Poe (Power Pass-Through)P6Kp8V-Rj45 (Mdix)
Auto-crossover (MDIX), which allow the RJ-45 ports to automatically Link with any RJ- 45 device and eliminate the use of cross-over cable. The RJ-45 pins normally (TP crossover switch) are per the standard for hubs-to- users twisted pair wiring: 1 = receive+, 2 = receive-, 3 = transmit+, 6 = transmit-, other pins not used. -
Page 65: 10B. New Poe(Power Inside), Model Pi6Kp8-45Rj (Mdix)
The PoE ports in Magnum 6K’s with 48VDC power input act as a pass- through, so the 48VDC power source must be strong enough to provide power to the 6K switch and to all the 8 RJ-45 ports with PD devices connected (up to 15 watts per PoE port). - Page 66 The PoE ports in Magnum 6K’s with 48VDC power input act as a pass- through, so the 48VDC power source must be strong enough to provide power to the 6K switch and to all the 8 RJ-45 ports with PD devices connected (up to 15 watts per PoE port).
-
Page 67: 6Kp8-45-2Mt Mtrj Small-Form-Factor
The 6KP8-45-2MT is equipped with six 10/100 RJ-45 ports and two 100Mb MTRJ fiber ports. When installed in a Magnum 6K32T & 6K32TRC Switch, it supports the standard distances as mentioned on 5.2.3. and the LEDs also act similarly. -
Page 68: Gbpm-2Otx (Two Gigabit Option)
Magnum 6K32T & 6K32TRC Managed Switch The GBIC transceiver has been offered in the modular slot with multiple options as per the user requirement. The two Giga port has been offered as GBPM-2OTX (fiber or RJ- 45), whereas the single Gigabit module comes in flavor of G+2 (100Mb fiber ports) or G+4(10/100 RJ-45 ports) as shown in the above figure. -
Page 69: Gbic-Lxsc Gigabit Fiber (1000Mb), Multi-Mode Sc
Magnum 6K32T & 6K32TRC Managed Switch Each port has an Full and Half Duplex (F/H) Activity, (ACT) LED indicating packets being received and a Link (LK) LED indicating proper connectivity with the remote device when lit 5.2.12b GBIC-LXSC Gigabit fiber (1000Mb), multi-mode SC Connector The Magnum GBIC-LXSC is a single-mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out. -
Page 70: Troubleshooting
However, if you are unsure of the procedures described in this section or if the Magnum 6K32T & 6K32TRC Switch is not performing as expected, do not attempt to repair the unit; instead contact your supplier for assistance or contact GarrettCom Customer Support. -
Page 71: When Calling For Assistance
Magnum 6K32T & 6K32TRC Managed Switch If the problem continues after completing Step 4 above, contact your supplier of the Magnum 6K32T & 6K32TRC Switch unit or if unknown, contact GarrettCom, Inc.by fax, phone or email (support@garrettcom.com) for assistance. When Calling for Assistance Please be prepared to provide the following information. -
Page 72: Shipping And Packaging Information
Testing and repair of product that is not under warranty will result in a customer (user) charge. Shipping and Packaging Information Should you need to ship the unit back to GarrettCom, please follow these instructions: Package the unit carefully. It is recommended that you use the original container if available. -
Page 73: Appendix B : Internal Dc Power Supply Options
GarrettCom. This warranty will not be effective if, in the opinion of GarrettCom, the product has been damaged by misuse, misapplication, or as a result of service or modification other than by GarrettCom. - Page 74 In this picture, the -48VDC terminal block on the Magnum 6K32T & 6K32TRC is located on the rear of the unit and is equipped with three (3) screw-down lead posts. It is similar for 24VDC and 125VDC options on Magnum 6K32T & 6K32TRC. The leads are identified as negative (-), positive (+), and chassis ground (GND).
- Page 75 Magnum unit, beginning with ground. Ensure that each lead is securely tightened. Note: The GND should be hooked up first. The 6K32T & 6K32TRC unit has a floating ground, so the user may elect to Ground either + or - terminal to suit the customer’s use.
-
Page 76: Appendix C: Internal Dc Dual-Source Power Option
Two separate sources, each at 88 - 150 VDC With the exception of the dual DC input power connections and the power supply, all specifications and configuration options for the Magnum 6K32T & 6K32TRC - 48VDC, 24VDC and 125VDC models with this Dual-Source option are identical to those listed in the Magnum 6K32T &... - Page 77 125VDC dual source leads to the -48VDC, 24VDC 7 125VDC power terminal block on the Magnum 6Ks Switch (shown in Figure ) The -48VDC terminal block on the Magnum 6K32T & 6K32TRC Switch, as shown in Fig C5.0 is located on the right rear of the unit and is equipped with five (5) screw-down lead posts.
- Page 78 Switch’s power terminals, positive (+) and negative (-) screws. Ensure that each lead is securely tightened. The 24VDC and 125VDC terminal block on Magnum 6K32T & 6K32TRC’s is similar to that described in the –48VDC information above. C5.1 UL Requirements The following must be adhered to in order to conform to UL requirements: Minimum 18 AWG cable for connection to a Centralized DC power source.