Advertisement
QUICK START GUIDE
1.
Camera's back box
2.
Screws attaching camera module to the back box
(x3, silver)
3.
Camera module / second housing
4.
Tilt bracket with locking screws
5.
Inner liner / Shroud
6.
IR board
7.
Dome bubble housing / Dome cover
8.
Screws securing the dome bubble housing to camera module (x3, silver)
9.
Lexan bubble
10. 3/4" Top conduit hole. During installation, sealant must be used to maintain the IP66
status.
11. 3/4" Side conduit hole. During installation, sealant must be used to maintain the
IP66 status.
DISASSEMBLING THE CAMERA
1. Use the provided security Torx
key to loosen three screws se-
curing the dome bubble housing
to camera module (#8). Do not
completely remove the screws
from the dome bubble
I/O CONNECTORS
Once the camera dome bubble has been removed, Ax73RM input/output connectors will
be revealed on the camera's module, including the microSD slot, Factory Reset and Factory
Default, analog RCA video jack, RJ-45 Ethernet/PoE connector, Audio and Alarm connectors
as well as a AC24V port.
1. Audio and Alarm I/O connectors.
2. AC 24V Port. Connect AC 24V power supply.
3. RJ-45 Ethernet Connector / PoE. Connect RJ-45 network cable for ethernet/internet
connectivity. PoE (Power over Ethernet) is supported.
NOTE on Power:
Do not apply power until the camera is properly and securely mounted.
4. Orange LED. Flashing orange LED indicates data transmission b/w camera and the
Internet.
5. Green LED. Solid green LED indicates a current live connection.
i3 INTERNATIONAL INC.
Locking
arms (x2)
2. Next, loosen three silver screws attach-
ing camera to the back box.
3. Remove camera's back box and set
aside.
Audio In
Audio Out Alarm Out Alarm In
www.i3international.com
Ax73RM-series 5MP IP Dome Camera
CONNECT CAMERA TO i3 SRX-PRO SERVER
LAN
Camera's default IP: 192.0.0.16. Default Login / PW: i3admin / i3admin
1. Close SRX-Pro Server software by pressing Alt+Shift+Ctrl+F4.
2. Change the IP address on the onboard NIC (LAN) (or on NIC1 if your SRX-Pro
Server has two onboard NIC cards) of your SRX-Pro Server to 192.0.0.XXX to
match the default IP range of your Annexxus IP camera.
3. Connect your camera to i3 SRX-Pro Server (see diagram above).
4. Turn on your Annexxus camera.
5. Launch the CD that came with your Annexxus camera and double-click
"AnnexxusFinder.exe" file to install Annexxus Finder application. Annexxus
Finder application discovers all Annexxus cameras connected to your network.
6. Select desired camera in the Annexxus Finder software by double-clicking it in
the list and click Edit.
7. Enter the new IP address and Subnet Mask of the camera in the Change IP
Address area. The new camera IP address must match the original range of your
SRX-Pro LAN or NIC1 card.
E.g. If your original SRX-Pro Server's IP address was 192.138.10.122, change
your Annexxus camera's IP address to 192.138.10.XXX.
8. Follow the Annexxus Finder installation instructions until the application has been
successfully installed on your SRX-Pro Server.
9. Double-click Annexxus Finder icon on the Desktop to launch the application.
The application window will appear displaying a list of active network cameras.
Remember: Annexxus Cameras cannot share an IP address, each camera
requires its own unique IP address.
10. Enter the default camera password: i3admin in the Input Password field and
click Save.
11. Wait a few moments for a successful confirmation window. Click OK to close it.
12. Repeat Steps 1-11 for all detected Annexxus cameras in the Annexxus Finder.
13. Make sure you can connect to the camera through Internet Explorer:
a. Launch Internet Explorer and enter the IP Address you have just assigned to
your Annexxus camera. The password window should be displayed.
b. Enter the default camera User Name: i3admin and default Password:
i3admin
c.
Annexxus camera interface will be displayed in the Internet Explorer
window. You should be able to see the camera image on the screen.
If you do not see the camera image on the screen, call i3 International tech
support for troubleshooting tips: 1.877.877.7241
14. Make sure that the latest version of GiPi updater is installed on your SRX-Pro
Server. You can download the updates from ftp://files.123ip.com/drivers/gipi.
Please contact i3 Technical Support team for access information.
15. Once the latest GiPi updater has been installed, restart i3 SRX-Pro Server.
16. Log In and go to the Setup -> IP Camera tab.
17. Click the Search button to display connected Annexxus cameras.
18. Select the detected camera in the list and click Select.
19. In the Select IP Camera window, enter the default camera User Name: i3admin
and default Password: i3admin, then click Add.
20. The selected camera will be added to the IP Camera list.
Don't forget to assign the IP camera to the SRX-Pro video channel in the
corresponding column.
21. Your Annexxus camera is now connected to SRX-Pro Server and is ready to
record. You may change resolution and frame rate for the Annexxus camera in
the IP Camera tab menu or you may choose to configure the camera's advanced
settings.
1.866.840.0004
U.S.A 1967 Wehrle Drive, Suite 1,
PMB# 034 Buffalo NY, 14221
Connection Type 1:
Crossover direct connection
Connection Type 2:
Via Gigabit Switch
Canada 780 Birchmount Road, Unit 16,
Scarborough, ON, M1K 5H4
i3 SRX-Pro Server
i3 SRX-Pro Server
Advertisement
