Related Manuals for videotronic SN-15AH PPHS
Summary of Contents for videotronic SN-15AH PPHS
- Page 1 Mounting and Operation Instructions Variable High Speed P/T Head SN-15AH/PPHS/ALU (Art. No. 560413) 03/03...
-
Page 3: Table Of Contents
GENERAL INFORMATION Contents General Information Safety Precautions Items Delivered Product Description Accessories and Additional Devices Mounting and Connecting the Camera Station Camera Station System Control with Video Matrix Mounting the Camera Station Connecting the Telemetry Receiver Connection Cable Type I and II Connecting the Video Signal Connecting the Operating Voltage Connecting the Interface... -
Page 4: General Information
GENERAL INFORMATION Dear Customer! By selecting this videotronic product you have decided to use a professional device which guarantees highest quality and reliability. We like to thank you very much for your confidence and kindly ask you to read the following instructions carefully before operating in order to be able to take full advantage of all quality features regarding this product. -
Page 5: Product Description
Videotronic BUSTRONIC RS-485 network. In combination with the Videotronic HQ System Camera (colour, mono or colour/mono) the variable speed is automatically controlled in relation to the zoom position (wide/ tele). This package embodies the most elegant and sophisticated PTZ camera unit available on the market. -
Page 6: Mounting And Connecting The Camera Station
MOUNTING AND CONNECTING Mounting and Connecting the Camera Station Camera Station System Control with Video Matrix Control of the entire system is done over the RS-485 interface of the KB-485 keyboard using a standard twisted pair telephone cable (shielded). To allow selection of specific camera stations within the system, all devices in the RS-485 BUS have to have an individual address. -
Page 7: Mounting The Camera Station
Attention When installing the camera station please make sure to follow the order mentioned below. Install the pan/tilt motor to a Videotronic WA-40BSN wall bracket using the attached installation material (M6 x 20 hex / M6 nut/ M6 washer). Fix the service junction box incl. power supply unit as near to the motor as possible. -
Page 8: Connecting The Telemetry Receiver
MOUNTING AND CONNECTING Connecting the Telemetry Receiver... -
Page 9: Connection Cable Type I And
MOUNTING AND CONNECTING Connection Cable Type I and II (to pan/tilt motor)) First of all you have to establish connection between motor and service junction box. Please make sure all connections are done according to the instructions. Wrong connections might destroy the complete unit. Please run all cables through the designated PG bolt connectors of the weatherproof junction box and fix the connectors tightly to avoid damage caused by humidity or leakage. - Page 10 MOUNTING AND CONNECTING (F)BAS Operation For standard transmission over coaxial cable connect the cable to the terminal block „Video Out“ (FBAS/GND) inside the service junction box. The shield of the coaxial cable has to be fixed with the strain relief clamp. Set the FBAS / Y jumpers as shown in the drawing! Y/C - Operation With a separated transmission of brightness and colour information (Y/C), the quality of...
- Page 11 MOUNTING AND CONNECTING Twisted Pair Video Transmission Transmission of the video signal via standard telephone cable is useful where you have existing telephone cable. This will significantly reduce your costs compared to additional coaxial connections. Via twisted pair you can achieve transmission distances of up to 1.500 metres.
-
Page 12: Connecting The Operating Voltage
MOUNTING AND CONNECTING Connecting the operating voltage 230 V AC / 50 Hz Connect the power cord to the terminal block „Operating Voltage“ inside the service junction box. The camera station has a primary fuse (2 AT). The secondary fuse has a value of 3.15 AT. -
Page 13: Configuring The Camera Station
MOUNTING AND CONNECTING Configuring the Camera Station To configure the camera station it is necessary to remove the lateral covers of the P/T unit in order to have access to the DIP switch blocks on the control circuit board. Setting the device address (switch 1 - 8 / DIP I) The RS-485 device address of the camera station has to be set using the DIP switches as shown in the drawing below. -
Page 14: Selection Of Correct Payload
≤ 5 kg / tracking mode The unit comes factory set with a payload of "≤ 5 kg". This corresponds to the videotronic Vitect camera housing. Control via RS-485 is not possible in tracking mode. Software: switch 11 / DIP I... -
Page 15: Preset Call Via Alarm Inputs
(1-64) are directly assigned to the corresponding position number (1-64). If you want to transfer the alarm of a camera station to a connected VIDEOTRONIC video matrix, switch 12 (DIP I) has to be set to position ON. The video matrix must have the system address „00“... - Page 16 MOUNTING AND CONNECTING Setting the PTZ camera as tracking camera The configuration of the camera station has to be finished before a hardware connection is established between the DITrec and the PTZ camera in order to prevent damaging the driver chips by excess voltages. Configuration is carried out in the junction box as well as in the PTZ head.
- Page 17 MOUNTING AND CONNECTING Configuring the camera station for tracking mode In order to configure the camera station it is necessary to remove both lateral parts of the PTZ head for getting access to both DIP blocks on the control circuit board. Software: switches 9 - 11 / DIP1 For altering the software the switches 9-11 have to be set according to the table shown below.
-
Page 18: Commissioning
MOUNTING AND CONNECTING For hardware set-up the switches 1-4 / DIP 2 have to be set according to the following table. In the factory setting the RS-485 is active. RS-232 switch 1 switch 2 switch 3 switch 4 N.B: You have to restart the system in order to activate the new settings Commissioning When you turn on the operating voltage (230 V/AC), the unit automatically starts a self test routine to check the horizontal and vertical limit switches and the motorzoom lens. -
Page 19: Setting The Horizontal And Vertical Limit Switches
MOUNTING AND CONNECTING Setting the horizontal and vertical limit switches The factory adjustment of the limit switches ensures that motor can only be moved in a relatively small range to avoid damage during installation caused by blind obstacles. After you have connected the operating voltage for the first time, the unit checks the limit switches and stores them into the internal memory. -
Page 20: Operating The Camera Station
MOUNTING AND CONNECTING Operating the camera station Control of the camera station is done with the BG-ALL control keys. To control the pan/tilt functions, use the arrow keys (up, down, left, right); to control the motorzoom lens, use the zoom and focus keys. Operating the motor with presets You can store up to 100 individual camera positions (00 - 99) and call them via alarm inputs or directly from the KB-485 keyboard. -
Page 21: Programming The Panorama Function
MOUNTING AND CONNECTING Programming the panorama function: The panorama function allows a tour through all preset camera positions in a pre- determined cycle. Camera positions 01 - XX will be called one after the other. The highest position number in the cycle can be programmed with the KB-485 keyboard. Following entries are possible: 1. -
Page 22: Programming The Home Position
MOUNTING AND CONNECTING Programming the home position: Home position is a freely programmable camera position to which the motor returns after a preset idle time period. The home position has the number „00“. Programming is done via the KB-485 keyboard. Following entries are possible: 1. - Page 23 MOUNTING AND CONNECTING Power Supply Only operate the device with the power supply adapter (12 V/DC) included in the scope of delivery. Connect the power supply adapter to the connector box (pos. 1) of the keyboard (please refer to the drawing). Plug the keyboard’s junction plug (pos. 1a) into the connector box (pos.
- Page 24 MOUNTING AND CONNECTING Configuring the Keyboard Addressing the Clients Each client in the RS485 BUS must have an individual device address between 00 and 255. An address may only be assigned once within the system. The address setting is carried out via 8 jumpers on each circuit board according to the following table. Each client can be addressed by its individual system address and receive control commands from the KB-485 keyboard.
-
Page 25: Connecting The Kb-485
EXHIBIT Connecting the KB-485 The KB-485 keyboard can control all of videotronic infosystems’ RS485 devices. The corresponding key commands for controlling the individual devices are described in this chapter. Key Assignment Function 0 - 9 numeric digit monitor symbol monitor selection... - Page 26 EXHIBIT Function of the display The following data is displayed: ♦ type of receiver When selecting SN-15AH/PPHS/ALU:Camera station ♦ selected address The currently selected address of the target client gets displayed (00 – 99) ♦ last command The last command gets displayed. This command is deleted after approximately 10 seconds.
-
Page 27: Technical Specifications
EXHIBIT Technical Specifications Max. payload: 15 kg Max. payload at V max.: 10 kg Application: outdoor / indoor ± 175° Pan movement: Pan / tilt min. 1,5°/sec. with manual control speed: max. 45°/sec. with manual control max. 90°/sec. during preset call Horiz. -
Page 28: Description Of Rs232 Interface
EXHIBIT Description of RS-232 Interface 9.600 Baud, 1 Start bit, 8 Data bits, No parity ESC L start horizontal left ESC i stop horizontal left/right ESC R start horizontal right ESC r stop horizontal left/right ESC D start vertical left (if camera mounted upside down: start vertical right) ESC d stop vertical left/right... -
Page 29: Rs-232 Interface In Tracking Mode
EXHIBIT RS-232 Interface in Tracking Mode The following parameters are valid in tracking mode: 19,200 Baud, 1 start / stop bit, 8 data bits, no parity, no handshake You have to restart the system in order to activate the new settings. ESC X A xxxx Reset of speed / acceleration / timeout (xxxx w/o significance) to reset value ESC X B xxxx... -
Page 30: Programming Control Sequences
EXHIBIT Programming Control Sequences: The required parameters are set according to the table above. Thereafter the positioning is activated with the ESC X Y command. Parameters can be altered or a new positioning can be called during the positioning process. The following parameters are executed immediately during the positioning process: •... -
Page 31: Crimping A Bnc Plug
EXHIBIT Crimping a BNC plug 1) Preparing the coaxial cable: To slip the rubber cap onto the end to be crimped, it must first be prepared. Dip the coaxial cable about 10 cm into metylated spirits (see fig. 2). Now slip on the rubber cap about 10 cm and the crimping cover about 5 cm (see fig. - Page 32 Tel.: 04321-879-0 Fax: 04321-879-97 Lahnstraße 1 D-24539 Neumünster/Germany Irrtümer sowie Änderungen, die dem technischen Fortschritt dienen, vorbehalten. Technical specifications are subject to change without prior notice. Bestell-Nr. M560413AG/032003 2003, videotronic infosystems Germany - printed in Germany Order No. M560413AC/032003...