Advertisement
S
T E P 3 ASSE MBL E SE AT FR AME AND SE AT BAC K
1. Attach Seat Frame(11) to Front Upright(4) using two 3/8"X3" Bolts(88), four 3/8" Washers(101) and two
3/8" Nuts(107). Attach Seat Frame(11) to Base Frame(1) using 3/8"X4-1/2" Bolt(87), two 3/8"
Washers(101) and one 3/8" Nut(107).
2. Attach Leg Extension Arm with bearing pre-installed(12) to Seat Frame(11) by aligning holes and then
inserting Leg Extension Axle(33). Fasten Leg Extension Axle(33) using two 5/16" Spring Washers(104),
two 5/16" Washers(102) and two 5/16"X5/8" Set Screws(97). Check to ensure that Leg Extension
Arm(12) pivots freely. Attach the Right and Left Leg Extension Arms(12R & 12L) to the Leg Extension
Arm(12) by 5/16"X1/2" Set Screw(113). Moisten the center of two Cover of Foam Pads(75A) and slide
onto each end of the Right and Left Leg Extension Arms(12R & 12L). Attach Plastic Washer (45A) at
both side of Cover of Foam Pad(75A) and secure the pads with 5/16"x32mm Sunken Head Screw(116).
Note: The L Pin(55) is used to lock the Leg Extension Arm(12) into place when using the low
cable for exercises such as arm curls, leg kicks, upright rows, etc. Remove the L Pin(55) when
performing leg extensions and leg curls.
3. Insert Foam Roller Bar(23) into hole in Chromed Seat Adjuster(16). Moisten Foam Pad(75) with water
and slide onto each end of Foam Rollers Bar(23). Attach Plastic Washer(45A) to both side of Cover of
Foam Pad(75A) and secure the Pads with 5/16"X32mm Sunken Head Screw(116).
4. Attach Seat Pad(77) to Chromed Seat Adjuster(16) using two 3/8" Washers(101) and two 3/8"X1-3/4"
Bolts(92). Attach 25X50mm Plug(44) to Chromed Seat Adjuster(16) and 50mm SQ. Plug(41) to Seat
Frame(11). Insert Chromed Seat Adjuster(16) into Seat Frame(11) and lock into place with Pop Pin(53)
with Spring(115).
5. Attach Seat Back Adjuster(17) to Front Upright(4) using one 3/8"X3" Bolt(88), two 3/8" Washers(101)
and 3/8" Nut(107). It may be necessary to tighten this bolt, then lossen just enough to let Seat Back
Adjuster(17) pivot freely. Attach Pop Pin(53) for Seat Back Adjuster(17) to Front Upright(4). Attach two
Metal Hinges(19) to top of Seat Back Adjuster(17), then attach Back Pad(76) to Metal Hinges(19) using
two 3/8"X1-3/4" Bolts(93) and two 3/8" Washers(101). Insert Foam Roller Bar(23) into hole in Seat
Back Adjuster(17). Moisten two Foam Pads(75) with water and slide onto each end of Foam Roller(23),
then attach Plastic Washer(45A) at both side of Cover of Foam Pads(75A) and secure pads with
5/16"x32mm Sunken Head Screw(116). Lock into place with pre-installed Set Screw.
6. Attach Weight Shroud(28) to Base Frame(1) and Top Guide Rod Retainer(7) using four 5/16"X1/2"
Bolts(95) and four 5/16" Washers(102).
Tighten all the bolts and nuts gradually.
116
45
23
76
75A
116
45
102
97
113
12R
12
110
116
45
75A
45A
45A
101
75
110
93
17
66
101
101
19
99
107
45A
45A
77
99
44
107
16
101
104
101
115
92
33
66
97
107
55
102
11
104
101
45A
99
12L
75A
93
88
4
75
45
116
45A
23
75A
45
116
101
88
45
116
8
1
101
87
7
102
95
102
95
28
28
102
95
102
95
Hide quick links:
Advertisement
