Table of Contents
Advertisement
8Channel stand-alone DVMR
3. DISPLAY SETUP
1) Edit camera title
Camera tile is 9 characters in length and includes alphabet in
a capital letter or small letter, numbers, and some special
letters.
Default camera title is CAM 1, CAM 2, and so on for channel 1,
channel 2 and so on.
Moving to a channel you want to change is done by pressing
[UP] and [DOWN] button, moving next character in a specific
camera tile is done by pressing [ENTER] button.
On the right side of display, there is series of letters in vertical,
and letter just behind triangular cursor is written whenever you
press [LEFT] or [RIGHT] button.
To save and exit EDIT CAMERA TITLE mode, press [MENU]
button.
2) Adjust colors
You can change parameter of camera color like brightness,
contrast, and others for each channel.
First select channel number whose parameters you want to
change, using [LEFT] and [RIGHT] button.
When you select channel, image from selected channel is
displayed. Then select element you want to change by pressing
UP] and [DOWN] button and adjust by pressing [LEFT] and
[RIGHT] button. You can see how it looks like whenever you
change values.
After you adjust parameters for channel you selected, then
select next channel for change.
To save and exit ADJUST COLOR mode, press [MENU] button.
3) Motion setup
In motion setup mode, you can set motion detection
area, sensitivity of motion, and detect windowrespectively,
channel by channel.
It is very important to set motion detection area,
sensitivity, and detect window, when you are going to
record just when motion is detected.
Motion detection area is important because DVMR
system just recognize motion in this area.
Sensitivity of motion specifies the sensitivity with
which DVMR system detect motion, and very slow
movement may not be detected if sensitivity of motion
is set at very low level.
Detection windows specifies size of moving object,
and DVMR system does not detect moving object
which is smaller in numbers of cell than detection
windows fixed in advance.
3. OPeration
ALL ABOUT IMAGE RECOGINITON & PROCESSING
EDIT CAMERA TITLE
ADJUST COLOR
MOTION SETUP
17
8Channel stand-alone DVMR
2) ALARM SETUP
In DVMR system, 8 alarm input, one for each channel, and 1
alarm output(relay out) is provided, and we can set type of
alarm sensor independently in ALARM SETUP.
Or you can set all of input alarm sensors at "NO", "NC" or
DISABLE by setting ALL at "NO", "NC" or DISABLE, by pressing
[ENTER] button or [LEFT] or [RIGHT] button.
In the same way, we can set type of relay out at "NO", "NC" or
DISABLE, by pressing [ENTER] button or [LEFT] or [RIGHT]
button.
To save settings and exit, press [MENU] button.
3) TIMER SETUP
In DVMR system, we have 3 kind of timer settings as follows.
FULL SCREEN timer :
Rotating cycle time of full screen in live mode, when [SEQ]
button is pressed for long time.
QUAD SCREEN timer :
Rotating cycle time of quad(4-split) screen in live mode, when
[SEQ] button is pressed for long time.
PIP SCREEN timer :
Rotating cycle time of PIP screen in live mode, when [PIP] button
is pressed in live mode.
If you press [SEQ] button for long time, full screen picture also
rotates with time interval of FULL SCREEN timer, in addition
to PIP.
To save settings and exit, press [MENU] button.
4) PAN/TILT CMD SETUP
Just with operation buttons on the front panel of DVMR unit,
we can control PTZ camera connected to DVMR unit via RS-485
port, if protocol of PTZ camera connected to DVMR unit is same
as one of built-in protocols, just select model among models in
PAN/TILT CMD SETUP.
In case PTZ camera you connected to DVMR unit is not a model
whose protocol in incorporated into DVMR unit, you are
requested to select USER DEFINE and input protocol by
yourself.
To save settings and exit, press [MENU] button.
3. OPeration
ALL ABOUT IMAGE RECOGINITON & PROCESSING
ALARM SETUP
TIMER SETUP
PAN/TILT CMD SETUP
22
Advertisement
Table of Contents
