Playback - Digital Watchdog Stand-alone DVMR User Manual

8Channel stand-alone DVMR
3) Example of Port Forwarding
Because ADSL is the most popular Internet service widely available in most of countries, we explain more
details about how to connect DVMR unit to ADSL line via Router or Gateway, to allow accessing to this
DVMR unit via Internet line far apart from DVMR unit.
Port forwarding : Port forwarding is called differently by each of router manufacturers, like IP forwarding,
IP bounding, port forwarding, port bounding or port routing. Our users can set port forwarding stated in
installation manual of router or gateway without big trouble, and complete IP network to which user can
connect many of our DVMRs, that are 1 ch DVMR, 4 ch DVMR, 8 ch DVMR and 16 ch DVMR,
to access to those units via Internet line far apart from those units.
Port forwarding is a kind of arrangement we have to set in web site of Router or Gateway to connect
external port to internal IP address, for example in above picture, PORT 8000 to IP 192.168.1.150,
PORT 8001 to IP 192.168.1.151, an so on.
According to our own test with NETGEAR Router, it is working perfectly, and we recommend our users
to adopt NETGEAR Router in case DVMR unit is connected to ADSL line.
3. OPeration
ALL ABOUT IMAGE RECOGINITON & PROCESSING
25
8Channel stand-alone DVMR

3-3. Playback

1. Playback setup
1) Press [PLAY] button to enter into playback mode.
2) [PLAY] button is is pressed shortly, it just start playback
from the previous stop point.
3) If you press [PLAY] button for longer time, you can enter
into GO TO MENU, and set the point from which you want to
start playback. You can set starting point of playback by
setting PERCENT, TIME/DATE, or EVENT LIST in GO TO
MENU.
4) Display screen will appear as shown on the right picture.
2. How to set in GO TO MENU
1) First select any one of PERCENT, TIME/DATE, and EVENT LIST using [UP] and [DOWN] buttons.
If you select PERCENT, you are supposed to set starting point of playback by percent.
If you select TIME/DATE, you are supposed to set starting point of playback by time and date.
If you select EVENT LIST, you will enter into event list and select one of event list to start playback
from selected event.
2) PERCENT
Press [ENTER] button when triangular cursor is in front of PERCENT to select target by percent.
In [PERCENT GO TO] menu, start and end point of recording shall be displayed. At the same time,
how many % of total HDD(1 or 2 units in DVMR unit) space is recorded is displayed. Under this line,
you are requested to set starting point of playback by % using [LEFT] and [RIGHT] button and [UP]
and [DOWN] button.
After you set starting point by %, press [ENTER] button shortly, and Target(starting point) is display in
time/date and at the same time playback starts from the point you set, while all message is displayed.
If it is the right point you want to start playback, then press [PLAY] button for longer time again to make
messages disappear.
To stop playback and go back to recording mode, press [PLAY] button shortly again.
3) TIME/DATE
Press [ENTER] button when triangular cursor is in front of TIME/DATE to select target by time/date.
In [TIME/DATE GO TO] menu, start and end point of recording shall be displayed.
Under this line, you are requested to set starting point of playback by time and date. Using [LEFT]
and [RIGHT] button and [UP] and [DOWN] button, set time and date from which you want to start
playback. Then press [PLAY] button shortly, and it starts to playback from the point you set, however
all messages are still displayed. If it is the right point from which you want to start playback, press
[ENTER] button for longer time once more, and messages shall be disappeared..
4) EVENT LIST
Press [ENTER] button when triangular cursor is in front of EVENT LIST to select target by event list.
In [EVENT-LIST GO TO] menu, list of event shall be displayed.
Just select event from which you want to start playback using [DOWN] and [UP] buttons, and then
press [PLAY] button shortly to start playback. If it is the right point from which you want to start
playback, press [ENTER] button once more to make all messages disappeared.
3. OPeration
ALL ABOUT IMAGE RECOGINITON & PROCESSING
GO TO MENU
14