ProScan Monitor/Receiver Owner's Manual page 45

P r o g r a m m i n g R e m o t e t o C o n t r o l a C a b l e B o x o r a n R C A D S S
If your cable box has its own remote to change channels,
you will probably be able to program the TV's remote to
control both the TV and the device. To program the
remote, just press and hold the
the two-digit code number for your brand of cable box.
Refer to the chart below to find the code number for your
cable box. Press the
POWER
operation. You may need to try each of the code numbers
listed until you find the one that works.
1 PRESS AND HOLD
DSS•CABLE.
REW
REC
DISPLAY
MUTE
1
4
2 PRESS TWO
7
INPUT
NUMBER
CLEAR
BUTTONS.
PIP
MOVE PIP
Brand of Cable-TV Box
ABC
Anvision
Cablestar
Diamond
Eagle
Eastern International
General Instrument
GI 400
Hamlin
Hitachi
Jerrold
MACOM
Magnavox
NSC
Oak
Oak Sigma
Panasonic
Philips
Pioneer
Randtek
RCA
Regal
Regency
Samsung
Scientific Atlanta
Signature
Sprucer
Starcom
Stargate 2000
Sylvania
Teknika
Texscan
Tocom
Unika
Universal
Viewstar
Warner Amex
Zenith
Note: Refer to the information sheet packed with your remote control
for the latest list of brand names and code numbers. Because this list is
constantly growing, the information sheet packed with your remote
control may be a later version of this list and contain additional brands
and/or code numbers.
button, then enter
DSS•CABLE
button next to confirm
VCR 2 • LD AUDIO
PLAY FF
STOP STOP PAUSE
SKIP
3 PRESS POWER
PREV CH
2 3
5 6
8 9
ANTENNA
0
•
RESET
SWAP
+
–
MOVE
FREEZE
CC
Code Number(s)
22, 46, 53, 54
07, 08
07, 08
07, 08
04, 05, 15, 23, 24, 25, 30, 36
03, 12, 13, 34, 48
37, 43, 46
04, 05, 15, 23, 24, 25, 30, 36, 45, 46, 47, 62
37, 43
07, 08, 19, 21, 26, 28, 29, 32, 33, 40, 41
01, 16, 38
03, 27, 39, 61
07, 08, 19, 21, 26, 28, 29, 32, 33, 40, 41
18, 20, 44
07, 08
00, 27
03, 12, 13
02, 33
03, 22, 35
11, 49
10, 11, 59
17, 21, 49, 50, 55
31, 32, 41
51, 52, 60
07, 08, 19, 21, 26, 28, 29, 32, 33, 40, 41
14, 42, 57
After the TV's remote is programmed, you'll be able to
turn on the cable box by pressing the
You can change channels on the cable box by
POWER.
pressing the
CHANNEL
"cable" mode. To put the remote in the "cable mode",
press the button. Press the
CABLE
remote back into the TV mode so the remote buttons will
control the TV again.
Programming Remote To Control Cable Box
with remote only
Refer to the chart at the left to find the code number that
corresponds to the brand name of your cable box. Keep
this number in mind. If more than one number is listed,
you may need to try each one separately until you find the
one that works.
1 Press and hold
DSS•CABLE
2 Press two number buttons (first one, then the other) to enter
the code number for your brand of cable box.
3 Point the remote at the cable box and press the power button
to test the code number.
• If the right number was entered, the cable box should turn
on. Pressing the
CHANNEL
channels on the cable box.
56
• If the cable box does not react to the remote (or if the remote
02
turns on the cable box but does not change channels), repeat
46
steps 1 thru 3 with another code number.
Operating Notes: After the remote is programmed, it will turn on
the cable box whenever you press
To turn off the cable box, press
To change channels on the cable box, press
09
up or down.
16
Programming Remote To control an RCA DSS
with remote only
44
The TV's remote has been pre-programmed to control the
46
®
RCA DSS Digital Satellite System receiver.
27
46
To control RCA DSS
58
button to put the remote in the "DSS
06
shown below will then control the DSS
1 Press
button to put the remote in
DSS•CABLE
Use the buttons and the
MOVE
44
®
through the DSS
®
R e c e i v e r
button, then
DSS•CABLE
buttons whenever the remote is in the
button to put the
TV
button on remote.
buttons should then also change
and then
•
POWER
DSS CABLE
then .
• ,
POWER
DSS CABLE
• then
DSS CABLE
® Receiver
®
receiver, first press the
DSS•CABLE
®
mode". The buttons
®
receiver.
®
"DSS
button to navigate
MENU•PROG
on-screen menus and features.
.
CHANNEL
mode."
41