Honeywell MS-5UD Series Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Smoke Alarm
  5. MS-5UD Series
  6. Manual

Honeywell MS-5UD Series Manual

Hide thumbs Also See for MS-5UD Series:
Table of Contents

Advertisement

Quick Links

PN: 52626:B
ECN 08-084
Fire Alarm Control Panels
MS-5UD Series
MS-10UD Series
Document
#52626
B
8/01/08
Revision:

Advertisement

Table of Contents
loading

Related Manuals for Honeywell MS-5UD Series

Summary of Contents for Honeywell MS-5UD Series

  • Page 1 PN: 52626:B ECN 08-084 Fire Alarm Control Panels MS-5UD Series MS-10UD Series Document #52626 8/01/08 Revision:...

  • Page 2: Fire Alarm System Limitations

    While a fire alarm system may lower insurance Fire Alarm System Limitations rates, it is not a substitute for fire insurance! An automatic fire alarm system–typically made up of age of flammable materials, etc.). smoke detectors, heat detectors, manual pull stations, Heat detectors do not sense particles of combustion and audible warning devices, and a fire alarm control panel with alarm only when heat on their sensors increases at a...

  • Page 3: Installation Precautions

    Adherence to the following will aid in problem-free Installation Precautions installation with long-term reliability: WARNING - Several different sources of power can be Like all solid state electronic devices, this system may connected to the fire alarm control panel. Disconnect all operate erratically or can be damaged when subjected to sources of power before servicing.

  • Page 4: Table Of Contents

    Table of Contents Product Description ..............................12 Product Features ..............................13 Specifications ..............................14 Controls and Indicators ............................16 Digital Alarm Communicator/Transmitter ......................17 Components ...............................18 Optional Modules and Accessories ........................18 Telephone Requirements and Warnings ......................20 Telephone Circuitry ............................20 Digital Communicator ..........................20 Telephone Company Rights and Warnings ....................21 For Canadian Applications .........................22 Installation ................................23 Backbox Mounting ............................23...
  • Page 5 Table of Contents ANN-LED Connection to FACP ......................51 ANN-RLY Relay Module ..........................52 ANN-RLY Board Layout ........................52 Specifications ............................52 Mounting/Installation ..........................52 ANN-RLY Connection to FACP ......................53 ANN-BUS Audio Panel ............................54 Programming .................................55 User Programming ............................55 Initial Power-up ..............................56 Programming Screens Description ........................56 Programming and Passwords ..........................57 Master Programming Level ..........................58 Input Zones ..............................59...
  • Page 6 Table of Contents Erase History ............................101 Walktest ..............................102 Clear Program .............................103 Password Change ............................103 Maintenance Programming Level ........................104 Input Zones - Enable/Disable ........................105 History ................................105 Walktest ..............................106 Time-Date ..............................107 Operating Instructions ............................108 Panel Control Buttons ............................108 Acknowledge/Step ............................108 Alarm Silenced ............................108 Drill/Hold 2 Sec ............................108 Reset ................................108 LED Indicators ..............................109...
  • Page 7 Table of Contents Transferring a Program ............................131 Security Features ............................131 Power Supply Calculations ............................133 Overview ................................133 Calculating the AC Branch Circuit ........................133 Calculating the System Current Draw .......................134 Overview ..............................134 How to Use Table 7-3 on page 134 to Calculate System Current Draw ............134 Calculating the Battery Size ..........................136 NFPA Battery Requirements ........................136 Selecting and Locating Batteries ........................136...
  • Page 8 Notes MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...
  • Page 9 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the standards set forth by the following regulatory agencies: • Underwriters Laboratories Standards • NFPA 72 National Fire Alarm Code • CAN/ULC - S527-99 Standard for Control Units for Fire Alarm Systems Before proceeding, the installer should be familiar with the following documents.
  • Page 10 MS-5UD Series Main Circuit Board MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...
  • Page 11 MS-10UD Series Main Circuit Board MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...

  • Page 12: Product Description

    Product Description Product Description SECTION 1 The MS-5UD is a five zone FACP (Fire Alarm Control Panel) and the MS-10UD is a ten zone FACP. The information in this manual refers to both the MS-5UD and MS-10UD unless otherwise specified. The combination control and digital communicator panels provide reliable fire signaling protection for small to medium sized commercial, industrial and institutional buildings.

  • Page 13: Product Features

    Product Description The following versions of the MS-5UD and MS-10UD are available: FACP Version Description MS-5UD-3 Five Zone Panel: 120 VAC with FLPS-3 power supply providing 3.0 amps total 24 VDC output current MS-5UD-7 Five Zone Panel: 120 VAC with FLPS-7 power supply providing 7.0 amps total 24 VDC output current MS-5UD-7C Five Zone Panel: 120 VAC with FLPS-7 power supply providing 7.0 amps...

  • Page 14: Specifications

    Product Description • Control Buttons ACK (Acknowledge) Alarm Silence System Reset/Lamp Test Drill • LED Indicators Fire Alarm Supervisory Trouble AC Power Alarm Silence Primary and Secondary Phone Line Active LEDs • Piezo sounder for alarm, trouble and supervisory • 24 volt operation •...
  • Page 15 Product Description Battery (sealed lead acid only) - J12 Maximum Charging Circuit - Normal Flat Charge: 27.6 VDC @ 1.4 amp Supervised, nonpower-limited Maximum Charger Capacity: 18 Amp Hour battery for MS-5UD-3(E), MS-10UD-3(E) and 26 Amp Hour battery for MS-5UD-7(E), MS-10UD-7(E) [two 18 Amp Hour batteries can be housed in FACP cabinet.

  • Page 16: Controls And Indicators

    Product Description Remote Sync Output - TB2 Remote power supply synchronization output, only required for the MS-5UD-3(E), MS-10UD- 3(E) [refer to "Remote Synchronization Output" on page 31] 24 VDC nominal special application power Maximum current is 40 mA End-of-Line Resistor: 4.7KΩ Supervised and power-limited circuit Auxiliary Trouble Input - J6 The Auxiliary Trouble Input is an open collector circuit which can be used to monitor an...

  • Page 17: Digital Alarm Communicator/Transmitter

    Product Description LED Indicators LEDs are provided to annunciate the following conditions: • Fire Alarm - red LED • Supervisory - yellow LED • AC Power - green LED • System Trouble - yellow LED • Alarm Silence - yellow LED •...

  • Page 18: Components

    Product Description 1.5 Components Main Circuit Board The main circuit board contains the system’s CPU, DACT and other primary components and wiring interface connectors. Optional modules plug in and are mounted to the main circuit board. Power Supply One power supply is provided standard with each FACP, mounted to a chassis. •...
  • Page 19 Product Description TR-CE Trim-ring A trim-ring TR-CE is available as an option. The trim-ring allows semi-flush mounting of the cabinet. Battery Box The BB-26 or BB-55 battery box may be used to house two batteries greater than 18 Amp Hour. The battery box mounts directly below the control panel cabinet, centered to the main circuit board.

  • Page 20: Telephone Requirements And Warnings

    Product Description 1.7 Telephone Requirements and Warnings 1.7.1 Telephone Circuitry Ringer Equivalence Number (REN) = 0.0B AC Impedance: 10.0 Mega Ohm Complies with FCC Part 68 Mates with RJ31X Male Connector Supervision Threshold: loss of phone line voltage for 2 minutes The REN is used to determine the quantity of devices which may be connected to the telephone line.

  • Page 21: Telephone Company Rights And Warnings

    Product Description 1.7.3 Telephone Company Rights and Warnings The telephone company, under certain circumstances, may temporarily discontinue services and/or make changes in its facilities, services, equipment or procedures which may affect the operation of this control panel. However, the telephone company is required to give advance notice of such changes or interruptions.

  • Page 22: For Canadian Applications

    Product Description 1.7.4 For Canadian Applications The following is excerpted from CP-01 Issue 5: NOTICE: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s).

  • Page 23: Installation

    Installation Installation SECTION 2 The cabinet can be surface mounted or semi-flush mounted. The door is removable during the installation period by opening and lifting it off the hinges. The cabinet mounts using two key slots at the top of the backbox and two additional securing holes located at the bottom. Carefully unpack the system and check for shipping damage.
  • Page 24 Installation Semi-Flush Mounting Do not recess box more than 3.875” into wall to avoid covering venting Hinge Slot for holes on top of box. optional Dress Panel Mounting slots for optional Trim Ring Semi- Flush mounting hole Hinge Slot for optional Dress Panel Figure 2.2 Cabinet Dimensions MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...
  • Page 25 Installation Figure 2.3 Backbox and Battery Box MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...

  • Page 26: Operating Power

    Installation 2.2 Operating Power WARNING: Several different sources of power can be connected to this panel. Disconnect all sources of power before servicing. The panel and associated equipment may be damaged by removing and/or inserting cards, modules or interconnecting cables while this unit is energized. Primary Power Source (AC) and Earth Ground Connections AC power connections are made inside the control panel cabinet.

  • Page 27: Input Circuits

    Installation 2.3 Input Circuits The MS-5UD has five IDCs (Initiating Device Circuits) and the MS-10UD has ten IDCs. Each circuit is compatible with System Sensor’s i smoke detectors which generate a maintenance signal when the detector becomes dirty and a separate supervisory ‘freeze’ signal when ambient temperature falls below the detector rating of approximately 45 F.
  • Page 28 Installation Combination Waterflow/Supervisory Zone A combination Waterflow/Supervisory circuit allows an FACP to distinguish between an Alarm switch (waterflow device) and a Supervisory switch (tamper) installed on the same circuit. Any circuit can be programmed as a Combo Type zone. The following figure illustrates the wiring of Zone 2 as a Style B (Class B) Waterflow/Supervisory circuit.

  • Page 29: Output Circuits

    Installation 2.4 Output Circuits 2.4.1 Notification Appliance Circuits Total current drawn from the four Style Y (Class B) Notification Appliance Circuits as well as other DC power outputs cannot exceed 3.0 amps for the MS-5UD-3(E), MS-10UD-3(E) [2.5 amp maximum per NAC] powered by the FLPS-3 power supply or 7.0 amps for the MS-5UD-7(C/E), MS-10UD-7(C/E) [3.0 amps maximum per NAC] powered by the FLPS-7 power supply (refer to "Power Supply Calculations"...

  • Page 30: Special Application Dc Power Output Connections

    Installation 2.4.2 Special Application DC Power Output Connections Special Application Resettable and Nonresettable 24 VDC power is available on the MS-5UD and MS-10UD control panel. Special Application 4-Wire Smoke Detector Power (500 mA) 24 VDC filtered, resettable power for 4-wire smoke detectors can be obtained from these terminals (power-limited) Special Application Resettable or Nonresettable Power (500 mA)

  • Page 31: Remote Synchronization Output

    Installation 2.4.4 Remote Synchronization Output Synchronization is a feature that controls the activation of notification appliances in such a way that all devices will turn on and off at exactly the same time. This is particularly critical when activating strobes which must be synchronized to avoid random activation and a potential hazard to individuals.

  • Page 32: Power-Limited Wiring Requirements

    Installation 2.5 Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” (6.35 mm) away from any nonpower- limited circuit wiring. Furthermore, all power-limited and nonpower-limited circuit wiring must enter and exit the cabinet through different knockouts and/or conduits.

  • Page 33: Digital Communicator

    Installation 2.6 Digital Communicator Two independent telephone lines can be connected to the control panel. Telephone line control/ command is made possible via double line seizure as well as usage of an RJ31X style interconnection. Note that it is critical that the panel's digital communicator be located as the first device on the incoming telephone circuit to properly function.

  • Page 34: Installation Of Optional Modules

    Installation 2.7 Installation of Optional Modules CAUTION: Remove all power (AC and DC) before installing or removing modules or wiring. 2.7.1 CAC-5X Class A Converter Module 2.7.1.1 Installation The CAC-5X Module can be used to convert five Style B (Class B) Initiating Device Circuits to Style D (Class A) and the two Style Y (Class B) Notification Appliance Circuits to Style Z (Class A).

  • Page 35: Wiring Nacs And Idcs For Class A

    Installation 2.7.1.2 Wiring NACs and IDCs for Class A Wire the Style Z (Class A) Notification Appliance Circuits using TB5 of the MS-5UD/MS- 10UD and TB2 of the CAC-5X module. Wire the Style D (Class A) Initiating Device Circuits using TB4 of the MS-5UD/MS-10UD and TB1 of the CAC-5X. Note that the wiring will be identical when using TB7 NAC and TB6 IDC of the MS-10UD.

  • Page 36: 4Xtmf Option Module

    Installation 2.7.2 4XTMF Option Module The 4XTMF module can be plugged into connectors J4 and J5 on the main circuit board. The following steps must be followed when installing the 4XTMF module: 1. Remove all power (AC and DC) from the FACP before installing the modules 2.

  • Page 37: 4Xtmf Transmitter Module Installation

    Installation 2.7.2.1 4XTMF Transmitter Module Installation The 4XTMF provides a supervised output for a local energy municipal box transmitter in addition to alarm and trouble reverse polarity. A jumper option allows the reverse polarity circuit to open with a system trouble condition if no alarm condition exists. A disable switch allows disabling of the transmitter output during testing to prevent accidental calling of the monitoring service.

  • Page 38: Ann-Bus Devices

    Installation 2.8 ANN-BUS Devices WARNING! Disconnect all sources of power (AC and DC) before installing or removing any modules or wiring. A variety of optional devices can be connected to the FACP ANN-BUS communication circuit. Compatible devices include: • ANN-80 LCD Annunciator •...
  • Page 39 Installation After calculating the total worst case current draw, Table 2.1 specifies the maximum distance the modules can be located from the FACP on a single wire run. The table ensures 6.0 volts of line drop maximum. In general, the wire length is limited by resistance, but for heavier wire gauges, capacitance is the limiting factor.

  • Page 40: Wiring Configuration

    Installation Wiring Distance Calculation Example: Suppose a system is configured with the following ANN-BUS modules: • 2 ANN-80 Remote Fire Annunciators • 1 ANN-S/PG Serial/Parallel Printer Interface Module • 1 ANN-I/O LED Driver Module The total worst case current is calculated as follows: ANN-80 Current Draw = 2 X 0.040 amps = 0.080 amps...

  • Page 41: Powering Ann-Bus Devices From Auxiliary Power Supply

    Installation 2.8.1.3 Powering ANN-BUS Devices from Auxiliary Power Supply Figure 2.19 illustrates the powering of ANN-BUS devices from an auxiliary power supply such as the FCPS-24FS6/8, when the maximum number of ANN-BUS devices exceeds the ANN- BUS power requirements. Cut Ground Fault Detection jumper JP1 (FACP monitors for ground faults) MS-5UD/MS-10UD ANN-BUS -24 VDC...

  • Page 42: Remote Fire Annunciator

    Installation 2.8.3 ANN-80 Remote Fire Annunciator The ANN-80 Annunciator is a compact, 80 character, backlit LCD remote fire annunciator which mimics the FACP display. It also provides system status indicators for AC Power, Alarm, Trouble, Supervisory and Alarm Silenced conditions. Communication between the ANN-80 and FACP is accomplished over a two wire serial interface employing the ANN-BUS communication format.

  • Page 43: Wiring Ann-80 To Facp

    Installation 2.8.5.3 Wiring ANN-80 to FACP The following steps can be used as a guide to wire the annunciator. Make certain all power has been removed from the FACP prior to annunciator installation. 1. Route wires from hole in backplate, through wiring channel and then to ANN-80 terminal block TB1 wiring channel wires...
  • Page 44 Installation FACP 4 3 2 1 ANN-BUS and power wiring are supervised and power-limited ANN-80 Figure 2.20 ANN-80 Wiring to FACP The following table shows the ANN-80 connections to the MS-5UD/MS-10UD. MS-5UD/MS-10UD (TB3) ANN-80 (TB1) Terminal 4 GND (-) Terminal 1 (-) Terminal 3 PWR (+) Terminal 2 (+) Terminal 2 A (ANN-BUS)

  • Page 45: Ann-S/Pg Serial/Parallel Printer Interface Installation

    Installation 2.8.6 ANN-S/PG Serial/Parallel Printer Interface Installation The ANN-S/PG Serial/Parallel Printer Interface module allows the ancillary connection of a serial or parallel printer to the FACP for a real-time log of system events, detector status reports and event history. Proceed with the installation as described in the following: 1.

  • Page 46: Connecting Prn-6F Printer

    Installation 2.8.6.2.1 Connecting PRN-6F Printer Remote printers require a primary AC power source. If required for the fire alarm system configuration (for example, a Proprietary Fire Alarm System), a remote printer requires a secondary power source (battery backup). Since a secondary power source is not provided as a standard feature, a separate UL-listed Uninterruptible Power Supply (UPS) should be used.

  • Page 47: Ann-I/O Led Driver Module

    Installation 2.8.7 ANN-I/O LED Driver Module The ANN-I/O is an LED driver module that can be used in a wide variety of applications, including as an interface with most customized graphic annunciators. The ANN-I/O can drive up to 40 LEDs. The following sections describe hardware installation. Refer to the section titled "ANN- BUS"...

  • Page 48: Ann-I/O Connection To Facp

    Installation 2.8.7.3 ANN-I/O Connection to FACP The ANN-I/O connects to the FACP via the ANN-BUS as illustrated in Figure 2.23. After the ANN-I/O is connected to the panel, it must be added to the system via FACP programming. ANN-I/O Module MS-5UD/MS-10UD ANN-BUS and power wiring are supervised and power-limited...

  • Page 49: Ann-I/O Module Led Wiring

    Installation 2.8.7.4 ANN-I/O Module LED Wiring There are four 12-pin connectors on the ANN-I/O module for connecting LEDs. Each set of 10 LEDs get their power from Pin 11 of the corresponding connector. Internal resistors are sized so that there is approximately 10 mA of current for each LED. No series resistors are required. LED outputs are mapped to output circuits.

  • Page 50: Ann-Led Annunciator Module

    Installation 2.8.8 ANN-LED Annunciator Module The ANN-LED annunciator module provides LED annunciation of general system faults and input zones when used with a compatible FACP. The ANN-LED module provides alarm (red), trouble (yellow) and supervisory (yellow) indication for up to ten input zones. Canadian Applications: The ANN-LED is supplied standard with the MS-5UD-7C and MS-10UD- 7C models.

  • Page 51: Ann-Led Connection To Facp

    Installation 2.8.8.4 ANN-LED Connection to FACP Figure 2.26 illustrates the ANN-LED board wiring connections to the FACP. ANN-LED FACP -24 VDC +24 VDC ANN-BUS Figure 2.26 ANN-LED Connection to FACP MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...

  • Page 52: Ann-Rly Relay Module

    Installation 2.8.9 ANN-RLY Relay Module The ANN-RLY relay module provides 10 programmable Form-C relays when used with a compatible FACP. 2.8.9.1 ANN-RLY Board Layout Figure 2.27 illustrates the ANN-RLY board showing locations of screw terminals for connection to the FACP and the DIP switches for selecting the ANN-BUS ID number. ANN-BUS (ID#) Address DIP switch ANN-BUS Connector...

  • Page 53: Ann-Rly Connection To Facp

    Installation 2.8.9.4 ANN-RLY Connection to FACP Figure 2.28 illustrates the ANN-RLY board wiring connections to the FACP. ANN-RLY FACP -24 VDC +24 VDC ANN-BUS Figure 2.28 ANN-RLY Connection to FACP MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...

  • Page 54: Ann-Bus Audio Panel

    Installation 2.9 ANN-BUS Audio Panel WARNING! Disconnect all sources of power (AC and DC) before installing or removing any wiring. The FACP must be enabled to communicate with the ACC-25/50ZS Audio Panel over the ANN- BUS (refer to "ANN-BUS Enabled" on page 80). This is accomplished by programming the Audio Panel ANN-BUS address into the FACP (refer to "BUS Modules"...

  • Page 55: Programming

    Programming Programming SECTION 3 NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION AND OTHER INVOLVED PARTIES This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to specific values or not used at all as indicated below: Program feature Permitted in...

  • Page 56: Initial Power-Up

    Programming Pressing 1, while this screen is being displayed, will cause the control panel to enter the Read Status Mode which allows the user to view the programmed features and status of the control panel The Read Status feature is not password protected. Refer to "Read Status" on page 118 for a detailed description of this feature.

  • Page 57: Programming And Passwords

    Programming 3.4 Programming and Passwords There are two factory set programming passwords which will access the Programming screens as indicated in the following examples. From either of the screens, access to specific system and device features or programming may be obtained. All user programming entries are stored in nonvolatile memory.

  • Page 58: Master Programming Level

    Programming 3.5 Master Programming Level When the Master Program Level password is entered, the control panel will enter user Programming mode. In this mode, the piezo sounder remains off, the trouble relay is activated and the system Trouble LED flashes until Programming mode is exited. The following display will appear: PROGRAMMING 1=INPUT ZONES...

  • Page 59: Input Zones

    Programming 3.5.1 Input Zones The Input Zones option allows the user to initially program or change the programming for the five input zones (circuits) on the MS-5UD or the ten input zones (circuits) on the MS-10UD. Pressing 1, while viewing Programming Screen #1, will select the Input Zones option and display a screen similar to the following: INPUT ZONES PROGRAMMING...

  • Page 60: Zone Type

    Programming The following examples show the editing of Input Zone 1: INPUT ZONE 1 1=ENABLED 2=TYPE PULL STATION 3=VERIFICATION Edit Input Zone Screen #2 INPUT ZONE 1 1=PAS/PRE-SIG DELAY NO DELAY Edit Input Zone Screen #3 INPUT ZONE 1 1=FREEZE SUPV. 2=ACC MSG# Edit Input Zone Screen #4 INPUT ZONE 1...
  • Page 61 Programming Pressing the down arrow key will display additional zone types as indicated in the following table. Note: Some of the following Zone Types are not available for Canadian applications. Refer to "Canadian Option" on page 79 for additional details. Zone Type Action When Activated Pull-Station...
  • Page 62 Programming PAS/Pre-Signal Delay Pressing 1 while viewing Edit Input Zone Screen #3 will display the following screen: PAS/PRE-SIG DELAY 1=NO DELAY 2=PRE-SIGNAL DELAY 3=PAS DELAY INPUT ZONE # 1=PAS/PRE-SIG DELAY NO DELAY PAS/Pre-Signal Delay Screen Edit Input Zone Screen #3 Pre-signal The Pre-signal option programs the zone to delay panel activation for a preprogrammed time delay of up to three minutes while allowing for visual verification by a person.
  • Page 63 Programming ACC Message Pressing 2 for ACC MSG # while viewing Edit Input Zone Screen #4 will cause the following screens to be displayed: ACC MSG NUMBER 1=NO MSG-ACTIVE INPUT ZONE # 2=NO MSG-INACTIVE 1=FREEZE SUPV. 3=MESSAGE 1 2=ACC MSG # Edit Input Zone Screen #4 ACC Message Screen #1 ACC MSG NUMBER...
  • Page 64 Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. Press the number corresponding to the adjective that is to be used as a descriptor for the location of the detector currently being programmed.
  • Page 65 Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be 1=STANDARD ADJECTIVE displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens. 2=STANDARD NOUN Press the number corresponding to the noun that is to be used as a descriptor for the location of 3=CUSTOM ADJECTIVE the detector currently being programmed.
  • Page 66 Programming Pressing 3 or 4 while viewing the Noun/Adjective Screen will display screens similar to the previous Adjective and Noun Screens. The new screens will list custom Adjectives and Nouns which have been programmed into the control panel by the user utilizing the PK-CD programming kit.

  • Page 67: Nac (Notification Appliance Circuit)

    Programming As an example, the user could quickly enter ‘FLR_3_ROOM_305’ as follows: 1. The cursor is on the first letter of the Adjective field. Press the zero key twice to display FLR_3 2. With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304.

  • Page 68: Enabled

    Programming 3.5.2.1 Enabled Pressing 1 while viewing NAC Screen #1 will cause the display to change to Enabled No. This will prevent the selected main circuit board NAC from activating its devices. Each press of the 1 key will cause the display to toggle between Enabled Yes and Enabled No. Note that if a circuit is disabled, a trouble will be logged on the FACP until the circuit is enabled.

  • Page 69: Two Stage Operation

    Programming The programmer can select the notification appliance output by pressing the number corresponding to the desired output. The coding selections are: • Steady - a continuous output with no coding • March Time - 120 ppm (pulse-per-minute) output • California - 10 seconds on and 5 seconds off •...

  • Page 70: Silence

    Programming 3.5.2.2.2.1 Maximum Number of Strobes for Synchronization The maximum current draw for a Notification Appliance Circuit cannot exceed 2.5 amps for models with the FLPS-3 power supply or 3.0 amps for models with the FLPS-7 power supply (refer to the AC Power section under "Specifications" on page 14). Refer to the manufacturer’s documentation supplied with the Strobes to determine the maximum current draw for each strobe and ensure that the circuit maximum is not exceeded.

  • Page 71: Auto Silence

    Programming 3.5.2.4 Auto Silence The Auto Silence feature, when enabled, automatically silences all main circuit board silenceable notification appliances after a programmed length of time. To enable this feature and program the time delay before Auto Silence activation, press 2 while viewing NAC Screen #2.

  • Page 72: Relay Type

    Programming To program Relay 1, 2 or 3, press the number corresponding to the selected relay. The following screens will appear for each relay to be programmed: RELAY TYPE RELAY TYPE 1=ALARM 1=COMM FAIL 2=TROUBLE 2=MEDICAL 3=SUPERVISORY 3=SILENCEABLE ALARM Relay Screen #1 Relay Screen #3 RELAY TYPE 1=PROCESS MONITOR...

  • Page 73: System Setup

    Programming 3.5.4 System Setup System Setup allows the programmer to configure the following control panel features: • Timers: This option allows the programmer to set the PAS (Positive Alarm Sequence) time delay, Pre-Signal time delay and Waterflow time delay • Banner: This option allows the user to change the top two lines of the LCD display from the factory default readout, which is blank, to a user defined readout when the control panel is in Normal condition...

  • Page 74: Timers

    Programming 3.5.4.1 Timers Timer delays for PAS, Pre-signal and waterflow activation can be programmed by pressing 1 while viewing System Setup Screen #1. The following screen will be displayed: TIMERS 1=PAS DELAY 2=PRE SIGNAL SYSTEM SETUP 1=TIMERS 3=WATERFLW DELAY 2=BANNER 3=TIME-DATE Timer Screen #1 System Setup Screen #1...

  • Page 75: Waterflow Delay

    Programming A flashing cursor is positioned in the lower left corner of the display. Enter a delay time consisting of three digits, such as 009 for nine seconds. Upon entering the third digit, the time delay will be stored in the control panel memory and the display will return to the Delay Screen which will indicate the new delay time.

  • Page 76: Banner

    Programming 3.5.4.2 Banner The top line of the display, which appears when the control panel is in normal mode, can be changed by using the Banner option. Pressing 2 while viewing System Setup Screen #1 will cause the following to be displayed: SELECT BANNER SYSTEM SETUP 1=FACTORY BANNER...

  • Page 77: Time-Date

    Programming 3.5.4.3 Time-Date SYSTEM SETUP 1=TIMERS The control panel time and date can be changed by pressing 3 while viewing the System Setup 2=BANNER Screen #1. The following screen will be displayed: 3=TIME-DATE System Setup Screen #1 TIME AND DATE 1=TIME 10:00 AM 2=DATE...

  • Page 78: Date

    Programming 3.5.4.3.2 Date To change the date, press 2 while viewing the Time-Date Screen. The following screen will be displayed: ENTER DATE **-**-**** MONTH DAY YEAR 07-07-2007 Date Screen A flashing cursor is located toward the top left of the display. Below the cursor is the current date.

  • Page 79: Trouble Reminder

    Programming Pressing 1 while viewing Daylight Savings Screen #2 will display another screen which allows the programmer to select the month that daylight savings time will end. In this sub-screen, pressing 1 will select September, 2 will select October and 3 will select November. Pressing 2 while viewing Daylight Savings Screen #2 will display two sub-screens which allow the programmer to select the week of the month that daylight savings time will end.

  • Page 80: Ann-Bus

    Programming 3.5.5.1 ANN-BUS Pressing 1 while viewing the Option Modules screen will cause the control panel to display the following screens. ANN-BUS 1=BUS ENABLED 2=BUS MODULES 3=AUTO CONFIGURE ANN-BUS Screen #1 ANN-BUS 1=ANN-S/PG OPTIONS 2=ANN-80 OPTIONS 3=ANN-RLY OPTIONS ANN-BUS Screen #2 ANN-BUS 1=ANN-AUDIO OPTIONS ANN-BUS Screen #3...

  • Page 81: Auto-Configure

    Programming In the technical information screen, pressing 1 for Type will display the following screens: ANN-BUS MODULE TYPE 1=NOT INSTALLED 2=ANN-80 3=ANN-I/O Module Type Screen #1 ANN-BUS MODULE TYPE 1=ANN-S/PG 2=ANN-RLY 3=ANN-LED Module Type Screen #2 ANN-BUS MODULE TYPE 1=ANN-AUDIO MODULE Module Type Screen #3 Press the number corresponding to the module type, if any, that is installed with the selected address.

  • Page 82: Ann-S/Pg Options Screen

    Programming 3.5.5.1.4 ANN-S/PG Options Screen The Printer Option allows the user to configure the optional printer. Pressing 1 while viewing the ANN-BUS Screen #2 will display the following screens: ANN-S/PG OPTIONS 1=PORT PARALLEL 2=PRINTER SUPV 3=OFFLINE TIMER PROGRAMMING 1=ANN-S/PG OPTIONS 2=ANN-80 OPTIONS Printer Options Screen #1 3=ANN-RLY OPTIONS...

  • Page 83: Ann-I/O Led Zone Assignments

    Programming 3.5.5.1.5 ANN-I/O LED Zone Assignments The information displayed by LEDs on every ANN-I/O module is not programmable and will therefore be as indicated in the following table. Zone (any address) AC Fault General Alarm General Supervisory General Trouble Alarm Silenced Earth Fault Battery Fault Charger Fault...

  • Page 84: Options Screen

    Programming 3.5.5.1.6 ANN-80 Options Screen Pressing 2 while viewing ANN-BUS screen #2 will display the following screen: ANN-80 OPTIONS 1=PIEZO ENABLE 2=LOCK ENABLE 3=ACK BTN ENABLE ANN-80 Options Screen #1 ANN-80 OPTIONS 1=SIL BTN ENABLE 2=RST BTN ENABLE 3=DRL BTN ENABLE ANN-80 Options Screen #2 The Piezo Enable option allows the programmer to select whether the piezo sounder on any installed ANN-80 module will ever sound.

  • Page 85: Ann-Rly Options Screen

    Programming 3.5.5.2 ANN-RLY Options Screen PROGRAMMING Pressing 3 for ANN-RLY Options while viewing ANN-BUS Screen #2 will cause the following 1=ANN-S/PG OPTIONS screen to be displayed: 2=ANN-80 OPTIONS 3=ANN-RLY OPTIONS ANN-RLY OPTIONS ANN-BUS Screen #2 1=RELAY 1 IN ZONE 1 2=RELAY 2 IN ZONE 2 3=RELAY 3...

  • Page 86: Ann-Audio Options Screen

    Programming 3.5.5.3 ANN-AUDIO Options Screen PROGRAMMING Pressing 1 for ANN-AUDIO Options while viewing ANN-BUS Screen #3 will cause the 1=ANN-AUDIO OPTIONS following screen to be displayed: ANN-BUS Screen #3 ANN-AUDIO OPTIONS 1=ALL CALL ZONE ANN-AUDIO Options Screen This screen shows the Input Zone that has been assigned to be the All-Call Zone. In this example, Zone 1 is the All-Call Zone.

  • Page 87: Onboard Dact

    Programming 3.5.5.4 Onboard DACT The Onboard DACT (Digital Alarm Communicator/Transmitter) provides communication to a central station. Pressing 2 while viewing the Option Module Screen will cause the following screens to be displayed: ON BOARD DACT 1=PRIM PHONE TCH TNE 2=SCND PHONE TCH TNE OPTION MODULES 3=CENTRAL STATION...

  • Page 88: Central Station

    Programming 3.5.5.4.3 Central Station Central Station programming configures the control panel DACT for contacting the central station. Pressing 3 while viewing Onboard DACT Screen 1 will cause the following screens to be displayed: ON BOARD DACT CENTRAL STATION 1=PRIM PHONE 1=REPORTING 2=SCND PHONE 3=CENTRAL STATION...

  • Page 89: Test Time Interval

    Programming 3.5.5.4.3.3 Central Station Primary and Secondary Phone Numbers Pressing 1 for Primary or 2 for Secondary, while viewing Central Station Screen #2, will display the following screens. Note that the following information must be entered for both the Primary and Secondary Central Station Phone Numbers.

  • Page 90: Account Code

    Programming Account Code Pressing 2 while viewing Primary/Secondary Screen #1 will cause the following screen to be displayed: ACCOUNT CODE RANGE 0000-FFFF Account Codes Screen The Account Code, which is assigned by a Central Station, depends on the communication format being used. The Account Code screen will have a flashing cursor in the lower left corner.

  • Page 91: Event Codes

    Programming Enter the digits as you would like the number to be dialed. For example, if it’s necessary to dial 9 before dialing a number outside the building, you may wish to pause after dialing 9. Enter 9 followed by D for a three second pause or E for a five second pause then the phone number followed by an F to indicate the end of the number.
  • Page 92 Programming The following table lists the Zone Alarm Types that can be programmed for zones 1 through 10 and the corresponding Event Codes for Ademco Contact ID and SIA DCS Formats. Note that Table 3.3 on page 93, Table 3.4 on page 94, Table 3.5 on page 95 and Table 3.6 on page 97 list the default settings for Zone 1 through Zone 10.
  • Page 93 Programming Ademco Contact ID Format - Primary Central Station Phone Number The information shown in Table 3.3 is automatically programmed for the Primary Central Station phone number Event Codes when Ademco Contact ID Format is selected. To disable event reporting, select the desired Event Code to be disabled and press 0 or Clear and then Enter to disable it.
  • Page 94 Programming Ademco Contact ID Format - Secondary Central Station Phone Number The information shown in Table 3.4 is automatically programmed for the Secondary Central Station phone number Event Codes when Ademco Contact ID Format is selected. To disable event reporting, select the desired Event Code to be disabled and press 0 or Clear and then Enter to disable it.
  • Page 95 Programming SIA-DCS Format - Primary Central Station Phone Number The information shown in Table 3.5 is automatically programmed for the Primary Central Station phone number Event Codes when SIA-DCS Format is selected. To disable event reporting, select the desired Event Code to be disabled and press 0 or Clear and then Enter to disable it.
  • Page 96 Programming Table 3.5 SIA-DCS Primary # Event Codes (Continued) Primary # Zone 5 Dirty Primary # Zone 6 Dirty Primary # Zone 7 Dirty Primary # Zone 8 Dirty Primary # Zone 9 Dirty Primary # Zone 10 Dirty FT10 FJ10 Primary # Earth Fault ET38...
  • Page 97 Programming SIA-DCS Format - Secondary Central Station Phone Number The information shown in Table 3.6 is automatically programmed for the Secondary Central Station phone number Event Codes when SIA-DCS Format is selected. To disable event reporting, select the desired Event Code to be disabled and press 0 or Clear and then Enter to disable it.
  • Page 98 Programming Table 3.6 SIA-DCS Secondary # Event Codes (Continued) Secondary # Zone 3 Dirty Secondary # Zone 4 Dirty Secondary # Zone 5 Dirty Secondary # Zone 6 Dirty Secondary # Zone 7 Dirty Secondary # Zone 8 Dirty Secondary # Zone 9 Dirty Secondary # Zone 10 Dirty FT10 FJ10...

  • Page 99: Service Terminal

    Programming 3.5.5.4.3.4 Trouble Call Limit (Dialer Runaway Prevention) CENTRAL STATION The Call Limit option limits the number of DACT trouble calls to the Central Station, to a 1=PRIMARY programmed amount between 0 and 99, for each unique trouble within a 24 hour period. 2=SECONDARY 3=CALL LIMIT Separate limit counters keep track of each unique type of trouble.

  • Page 100: Supervised Phone Line

    Programming 3.5.5.4.4.1 Ring Count The ring count designates the number of rings allowed on the phone line prior to answering an SERVICE TERMINAL 1=RING COUNT incoming call from a service terminal. The factory default is 0 which means the control panel will not answer an incoming call.

  • Page 101: View Events

    Programming 3.5.6.1 View Events HISTORY Pressing 1 while viewing the History Screen will allow the user to select the events to be 1=VIEW EVENTS viewed as illustrated in the following: 2=ERASE HISTORY History Screen HISTORY 1=VIEW ALL 2=VIEW ALARMS 3=VIEW OTHER EVENTS View Events Screen While displaying the View Events screen, press 1 to view all events, 2 to view only alarms or 3 to view other events.

  • Page 102: Walktest

    Programming 3.5.7 Walktest Walktest allows an individual to test the fire alarm system without the necessity to reset the control panel after each device activation. Refer to the sections titled "Walktest" on page 106 and "Walktest" on page 117 for additional information regarding the Walktest feature. Pressing 1 while viewing the Programming Screen #3 will cause the following Walktest options to be displayed: WALKTEST 1=SILENT...

  • Page 103: Clear Program

    Programming 3.5.8 Clear Program Pressing 2 while viewing Programming Screen #3, will select the Clear Program option. The control panel will provide a warning to the user by prompting with the following display: WARNING! SYSTEM CHANGE PROGRAMMING 1=WALKTEST PROCEED? 2=CLEAR PROGRAM 1=YES 2=NO 3=PASSWORD CHANGE...

  • Page 104: Maintenance Programming Level

    Programming 3.6 Maintenance Programming Level To access Maintenance Programming mode, press the Enter key. The LCD will display the following: 1=READ STATUS 2=PROGRAMMING 3=REMOTE DOWNLOAD To enter the Maintenance Programming mode, press 2. The display will read as follows: PROGRAMMING ENTER PASSWORD When the Maintenance level password (default 11111) is entered, the following screen will appear: PROGRAMMING...

  • Page 105: Input Zones - Enable/Disable

    Programming 3.6.1 Input Zones - Enable/Disable The Zone Setup option allows the user to enable or disable desired zones. Pressing 1 for Zone Setup, while viewing Maintenance Screen #1 will cause the following screens to be displayed: POINT PROGRAM 1=ZONE 1 PROGRAMMING 2=ZONE 2 1=INPUT ZONES...

  • Page 106: Walktest

    Programming Pressing 1 while viewing the History screen will cause the following screen to be displayed: HISTORY 1=VIEW ALL 2=VIEW ALARMS 3=VIEW OTHER EVENTS To view all the events which have occurred in the control panel since the history file was last erased, press 1 while viewing the Events screen.

  • Page 107: Time-Date

    Programming 3.6.4 Time-Date To program the time and date into the control panel, press 1 while viewing Maintenance Screen #2. The following display will appear: TIME AND DATE PROGRAMMING 1=TIME 01:00 AM 1=TIME-DATE 2=DATE 01-01-2001 3=CLOCK FORMAT 12HRS Maintenance Screen #2 Time and Date Screen To change the time, press 1 to display the following screen: ENTER TIME AS 12HRS...

  • Page 108: Operating Instructions

    Operating Instructions Operating Instructions SECTION 4 4.1 Panel Control Buttons 4.1.1 Acknowledge/Step The first press of the Acknowledge/Step key silences the piezo sounder, changes flashing LEDs to steady and also changes the status field on the LCD display from capital letters to small letters (TROUBL to Troubl).

  • Page 109: Led Indicators

    Operating Instructions 4.2 LED Indicators The five LED indicators, which are located on the front panel, operate as follows: AC Power This is a green LED which illuminates if AC power is applied to the FACP. A loss of AC power will turn off this LED Fire Alarm This red LED flashes when one or more alarms occur.

  • Page 110: Trouble Operation

    Operating Instructions 4.4 Trouble Operation With no alarms in the system, the detection of a trouble will cause the following: • The piezo to pulse 1 second On and 1 second Off • The system Trouble LED to flash one second On and one second Off •...

  • Page 111: Alarm Operation

    Operating Instructions Pressing the Acknowledge/Step or Alarm Silence key will cause the pulsing piezo to silence and the system Trouble LED to change from flashing to on steady. This block acknowledgment occurs regardless of the number of troubles, alarms and supervisory events active in the system. When the Acknowledge/Step key is pressed and at least one new alarm or trouble exists in the system, the ‘acknowledge’...

  • Page 112: Supervisory Operation

    Operating Instructions • Fourth line in display: Time; the current time in this example is 10:00A which represents 10:00 AM Date; the current month, day and year in this example is 09 for September, 08 for the 8th day of the month and 07 for the year 2007 4.6 Supervisory Operation Supervisory operation is similar to alarm operation but with the following differences: •...

  • Page 113: Process Monitor Operation

    Operating Instructions 4.7 Process Monitor Operation Process Monitor operation will initiate the following events: • The piezo sounder pulses ¼ second On and ¼ second Off • The LCD displays a process monitor message along with the device name, type, adjective/ noun, associated zones and time/date •...

  • Page 114: Disable/Enable Operation

    Operating Instructions 4.10 Disable/Enable Operation Input zones which are disabled do not cause an alarm or any zone activation. Disabled NACs are held in the off state. All disabled zones/NACs are treated as if they were in trouble, with the exception being the status label that will be displayed is DISABL.

  • Page 115: Presignal

    Operating Instructions 4.15 Presignal Presignal option programs an initiating device to delay the activation of NACs while allowing visual verification by a person. Once a detector triggers an alarm, the onboard piezo sounds immediately, but the NACs are not activated for a user programmed time duration of up to three minutes.

  • Page 116: Special System Timers

    Operating Instructions 4.17 Special System Timers 4.17.1 Silence Inhibit Timer This option, if selected, prevents the Alarm Silenced and Reset keys from functioning for 60 seconds following an alarm. A new alarm during the initial 60 second period will not cause the timer to restart with a new 60 seconds.

  • Page 117: Alarm Verification (None Or One Minute)

    Operating Instructions 4.17.5 Alarm Verification (None or One Minute) If alarm verification is selected, a smoke detector activation will cause the FACP to reset the detector by removing power for 6 seconds. Power is reapplied and a 17 second retard period begins which allows all detectors to stabilize.

  • Page 118: Read Status

    Operating Instructions 4.19 Read Status Read Status functions do not require a password. The control panel will continue to provide fire protection while in Read Status mode. This mode can be entered while the control panel is in alarm or trouble. If a new alarm or trouble occurs during these functions, the Read Status is exited to prevent confusion.

  • Page 119: Input Zones

    Operating Instructions 4.19.1 Input Zones Pressing 1 while viewing Read Status Screen #1 will cause the following screens to be displayed: ZONE STATUS 1=ZONE 1 2=ZONE 2 READ STATUS 1=INPUT ZONES 3=ZONE 3 2=NACS 3=RELAYS Read Status Screen #1 Pressing the down arrow key will allow the selection of Zones 4-5 for the MS-5UD and Zones 4-10 for the MS-10UD.

  • Page 120: Relays

    Operating Instructions The resulting screens will display the following information: • Enable/Disable Status • Coding Selection (Temporal, Steady, etc.) • Silenceable/Nonsilenceable • Auto Silence Enable/Disable and time delay (in minutes) • Silence Inhibit Enabled/Disabled 4.19.3 Relays READ STATUS Pressing 3 while viewing Read Status Screen #1 will display the following screen: 1=INPUT ZONES 2=NACS 3=RELAYS...

  • Page 121: Timers

    Operating Instructions 4.19.5 Timers Pressing 2 while Read Status Screen #2 will display the following screen: TIMERS PAS DELAY READ STATUS PRE SIGNAL 1=SYSTEM SETTINGS 2=TIMERS WATERFLW DELAY 3=DAYLIGHT SAVINGS Read Status Screen #2 TIMERS AC LOSS DELAY These screens allow the operator to view the various timer settings. 4.19.6 Daylight Savings Pressing 3 while Read Status Screen #2 will cause the following screens to be displayed: DAYLIGHT SAVINGS...

  • Page 122: History

    Operating Instructions 4.19.7 History Pressing 1 while viewing Read Status Screen #3 will display the following screens: HISTORY 1=VIEW ALL 2=VIEW ALARMS READ STATUS 3=VIEW OTHER EVENTS 1=HISTORY 2=PRINTER 3=ANN-BUS Read Status Screen #3 The operator can view all events which have been stored in the history file, only alarms or other events, such as troubles or supervisories, by pressing the corresponding number key.

  • Page 123: Ann-Bus

    Operating Instructions 4.19.9 ANN-BUS Pressing 3 while viewing Read Status Screen #3 will display the settings for the ANN-BUS options as shown in the following screens: ANN-BUS READ STATUS BUS ENABLED 1=HISTORY 2=PRINTER 1=BUS MODULES 3=ANN-BUS 2=ANN-S/PG OPTIONS Read Status Screen #3 ANN-BUS Screen #1 ANN-BUS 1=ANN-80 OPTIONS...

  • Page 124: Central Station

    Operating Instructions 4.19.10 Central Station Pressing 1 while viewing Read Status Screen #4 will display the following screens: CENTRAL STATION REPORTING READ STATUS REPORT STYLE 1=CENTRAL STATION BOTH 2=PHONE LINES 3=SERVICE TERMINAL Central Station Screen #1 Read Status Screen #4 CENTRAL STATION 1=PRIMARY 2=SECONDARY...

  • Page 125: Phone Line 2

    Operating Instructions 4.19.11 Phone Line Pressing 1 while viewing Read Status Screen #4 will display the following screen: PHONE LINES PRIMARY TCH TNE SECONDARY TCH TNE 3=SUPERV PHONE LINE The second and third lines of this screen indicate that both the Primary and Secondary phone lines have been configured for touchtone dialing operation.

  • Page 126: Central Station Communications

    Central Station Communications Central Station Communications SECTION 5 The control panel transmits zone and system status reports to Central Stations via the public switched telephone network. Two supervised telephone line connections are made to interface the control panel to the telephone lines. Two optional 7 foot telephone cords are available for this purpose and can be purchased separately.

  • Page 127: Transmittal Priorities

    Central Station Communications 5.1 Transmittal Priorities The integral communicator transmits highest priority events first. Events, in terms of priority, are listed below in descending order: 1. Alarms (highest priority level) Pull stations Waterflow Smoke detector Other alarm types 2. Supervisory Zone 3.
  • Page 128 Central Station Communications The table below shows UL listed receivers which are compatible with the MS-5UD and MS-10UD. Table 5.1 Compatible UL Listed Receivers Format SIA-DCS-8 SIA-DCS-20 Ademco Contact ID 1. With 685-8 Line Card with Rev. 4.4d software 2. With 124060V206B and 124063 Line Card Rev. B 3.

  • Page 129: Local/Remote Site Upload/Download

    Local/Remote Site Upload/Download Local/Remote Site Upload/Download SECTION 6 The control panel may be programmed or interrogated off-site via the public switched telephone ™ network or locally using a USB cable. Any personal computer with Windows XP or later, with a 2400 baud compatible modem or USB port and Upload/Download software PS-Tools on the CD ROM P/N PK-CD, may serve as a Service Terminal.
  • Page 130 Local/Remote Site Upload/Download Pressing 3 for Remote Download while viewing the main menu will cause the following screen to be displayed: REMOTE DOWNLOAD ENTER PASSWORD ***** The Remote Download password (default 00000) must be entered to access the Remote Download feature.

  • Page 131: Transferring A Program

    Local/Remote Site Upload/Download 6.2 Transferring a Program The first time that the control panel is contacted, a secret code is loaded in by a Service Terminal. Future upload or download requests cause verification of the secret code by the control panel before processing of data is allowed.
  • Page 132 Local/Remote Site Upload/Download Error Checking As each block of data is received by the control panel, it is checked for accuracy. If an error is detected, the block is retransmitted until correct, up to a maximum of four times. If the Secret Code is not verified and four errors occur, the call is disconnected and the report that the upload/ download was not successful is called to the Central Station(s).

  • Page 133: Power Supply Calculations

    Power Supply Calculations Power Supply Calculations SECTION 7 7.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step process, consisting of the following: 1. Calculating the total amount of AC branch circuit current required to operate the system 2.

  • Page 134: Calculating The System Current Draw

    Power Supply Calculations Calculating the System Current Draw 7.3.1 Overview The control panel must be able to power all internal and external devices continuously during the non-fire alarm condition. To calculate the non-fire alarm load on the system power supply when primary power is applied, use Calculation Column 1 in Table 7-3 on page 135.
  • Page 135 Power Supply Calculations Table 7-3 contains three columns for calculating current draws. For each column, calculate the current and enter the total (in amperes) in the bottom row. When finished, copy the totals from Cal- culation Column 2 and Calculation Column 3 to Table 7-4 on page 136. TABLE 7-3:System Current Draw Calculations Calculation Column 1 Calculation Column 2...

  • Page 136: Calculating The Battery Size

    Power Supply Calculations Calculating the Battery Size Use Table 7-4 to calculate the total Standby and Alarm load in ampere hours (AH). This total load determines the battery size (in AH), required to support the control panel under the loss of AC power.

  • Page 137: Ademco Contact Id Format Event Code Descriptions

    Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Format APPENDIX A Event Code Descriptions This appendix describes the various Event Codes and their messages which are available for the Ademco Contact ID Format. A.1 Transmission Format Between DACT and Receiver The transmission string for the Ademco Contact ID Format is as follows: SSSS 18 QXYZ GG CCC where SSSS...
  • Page 138 Ademco Contact ID Format Event Code Descriptions EVENT CODE CLASSIFICATIONS ALARMS SUPERVISORY TROUBLES DISABLES/ OPEN/CLOSE TEST/ BYPASSES REMOTE ACCESS MISC. Medical Fire System Open/Close System Test Fire Sounder/Relay Remote Access Sounder/Relay Panic System Peripheral Access Control System Peripheral Burglary Communication Communication General Protective Loop...
  • Page 139 Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE 24 Hour Non-Burglary - 150 and 160 150 24-Hour Non-Burg ALARM - 24-Hr. Non-Burg - # 151 Gas detected ALARM - Gas Detected - # 152 Refrigeration ALARM - Refrigeration - # 153 Loss of heat ALARM - Heating System - # 154 Water leakage...
  • Page 140 Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE Communication Troubles - 350 and 360 350 Communication TROUBLE - Communication Trouble 351 Telco 1 fault TROUBLE - Phone Line #1 352 Telco 2 fault TROUBLE - Phone Line #2 353 Long range radio xmitter fault TROUBLE - Radio Transmitter 354 Fail to communicate TROUBLE - Fail to Communicate...
  • Page 141 Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE Sounder/Relay Disables - 520 520 Sounder/Relay disable DISABLE - Sounder/Relay - # 521 Bell 1 disable DISABLE - Bell/Siren - #1 522 Bell 2 disable DISABLE - Bell/Siren - #2 523 Alarm relay disable DISABLE - Alarm Relay 524 Trouble relay disable DISABLE - Trouble Relay...

  • Page 142: Nfpa Standard-Specific Requirements

    NFPA Standard-Specific Requirements NFPA Standard-Specific Requirements APPENDIX B The MS-5UD/MS-10UD has been designed for use in commercial, industrial and institutional applications and meets the requirements for service under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: MS-5UD/MS-10UD Control Panel Contains the main control board, cabinet (backbox and door), main power supply and transformer.
  • Page 143 NFPA Standard-Specific Requirements The following figure illustrates an example of Central Station/Remote Station Reporting using a 411UD. The relay contacts from the MS-5UD/MS-10UD may be used to trip any dialer UL listed for Central Station/Remote Station Reporting Services. 411UD Channel1 Channel 2 Channel 3 Channel 4 (2.2K ELR)
  • Page 144 NFPA Standard-Specific Requirements 411UD FACP Alarm TB2-1 TB8-1 TB2-2 TB8-3 Trouble TB2-3 TB8-4 TB2-4 TB8-6 Supervisory TB2-5 TB8-7 TB2-6 TB8-9 Table B.1 411UD Connections to FACP Notes: 1. Reference the 411UD Manual for additional information 2. Program the 411UD for slave operation 3.
  • Page 145 NFPA Standard-Specific Requirements NFPA 72 Auxiliary Fire Alarm System All connections are power-limited and supervised. This application is not suitable for separate transmission of sprinkler supervisory or trouble conditions. Notes: 1. 3 ohms maximum loop resistance allowed for wiring from control panel to Municipal Box. 2.
  • Page 146 NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: 1. Cut Jumper JP30 on the MS-5UD/MS-10UD main circuit board to supervise placement of the 4XTMF module. 2. Refer to "4XTMF Transmitter Module Installation" on page 37 for detailed information. RS82 Remote Station Receiver UL listed.
  • Page 147 NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems Fire Alarm Control Panel FACP Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automatically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition.

  • Page 148: Central Station/Remote Station Transmitter: Connection To Facp Dry Contacts

    NFPA Standard-Specific Requirements B.1 Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts The dry contacts of the FACP programmable relays can be used to trip a UL-864 Listed Central Station/Remote Station Transmitter. The FACP contacts must be supervised by the Central Station/ Remote Station Transmitter module using End-of-Line Resistors (ELRs) with a value determined by the Transmitter manufacturer.

  • Page 149: Facp With Keltron

    FACP with Keltron FACP with Keltron APPENDIX C The following figure illustrates the connections between the FACP and Keltron Receiver/Transmitter. CAUTION! For reasons of wiring diagram clarity, terminal designations of Keltron modules are not shown in actual order. Follow Keltron manual and module markings for exact terminal locations to prevent severe module damage! IMPORTANT! All connections between the FACP and Keltron modules must be made within 20 feet and enclosed within conduit or equivalently protected against mechanical...

  • Page 150: Wire Requirements

    Wire Requirements Wire Requirements APPENDIX D Connecting external system accessories to the main circuits must be carefully considered to ensure proper operation. It is important to use the correct type of wire, gauge and run length for each circuit. Reference the chart below to specify wire requirements and limitations for each circuit. Table D.1 FACP Wire Specifications CIRCUIT CONNECTIONS WIRE REQUIREMENTS...

  • Page 151: Ms-5Ud-3(E) & Ms-10Ud-3(E) Nac Wiring

    Wire Requirements D.1 MS-5UD-3(E) & MS-10UD-3(E) NAC Wiring The following table lists NAC wiring requirements for the MS-5UD-3(E) & MS- 10UD-3(E) FACP which utilizes the FLPS-3 power supply. Table D.2 NAC Wiring Requirements for FACP with FLPS-3 Power Supply CLASS-B CLASS-A Max.
  • Page 152 Notes MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...
  • Page 153 Index Numerics Backup Reporting 88 10 Zone Main Circuit Board 11 Banner 73 24 Hour Test Time 90 setting 76 4XTM 146 battery 18, 26 4XTMF 146 precautions 26 installation 37 rating 15 see also Transmitter module 18, 37 battery box 19 4XTMF installation 36 mounting 24, 25 5 Zone Main Circuit Board 10...
  • Page 154 Index Control Buttons 108 see also relay 12 control buttons 14 freeze 27 controls 16 freeze signal current see also smoke detector monitoring 12 nonresettable power 30 resettable power 30 Hazard Condition 113 total output 29 History 100 current requirements for system 134, 135 erase 101 Maintenance Level 105 DACT...
  • Page 155 Index Fire Alarm 14, 17, 109 NFPA Standard 142 Supervisory 14, 17, 109 nonpower-limited wiring 32 System Trouble 17 nonresettable power 12, 15, 30 Trouble 14, 109 current 30 Local Programming 55 maximum current 15 Normal 109 main circuit board normal display 55 see also 10 zone main circuit board 11 Notification Appliance Circuit 12, 15, 29, 67...
  • Page 156 Index see also battery 26 Reporting Enable 88 power supply calculations 133 Reset 14, 16, 108 power-limited wiring 32 resettable power 12, 15, 30 Power-up current 30 first time 56 maximum current 15 Pre-signal 62 reverse polarity circuit function 115 see also Transmitter module 18 Pre-signal Delay timer 74 Ring Count 100...
  • Page 157 Index Time-Date combination waterflow/supervisory 28 Maintenance Level 107 IDC 27 Time-Date setting 73, 77 NAC 29 Time-out 131 nonpower-limited 32 Timers 73 power-limited 32 Transmittal Priorities 127 UL requirements 32 Transmitter Module 18 Transmitter module Zone operation 37 type 60 specifications 37 verification 61 transmitter module 37...
  • Page 158 Notes MS-5UD/MS-10UD Series PN 52626:B 8/01/2008...

  • Page 159: Limited Warranty

    This warranty is void if the product is altered or repaired by anyone other than Honeywell International Inc. or as expressly authorized by Honeywell International Inc.
  • Page 160 World Headquarters 1 Firelite Place Northford, CT 06472-1653 USA 203-484-7161 fax 203-484-7118 www.firelite.com...

This manual is also suitable for:

Ms-10ud series

Table of Contents