Terminal Descriptions; Board Connectors; About The Keypad; Keypad Key Functions - Bosch Solution 16plus Quick Start Manual

Te rmi nal De sc ri pti on s
Nº Name
Earth wire from this terminal is connected
1 Earth
to the Mains earth.
2 ~ (AC) Connection of the A.C. plug pack
3 ~ (AC) transformer
4 BAT (-) Negative and positive connections to the
5 BAT (+) stand-by battery. 12 VDC / 7AH
6 +12 V
7 +12 V
These terminals are used to power
8 +12 V
detectors and LAN devices up to 750
9 GND
mA.
10 GND
11 GND
12 LAN + These terminals are used to power LAN
13 LAN - devices up to 750 mA.
Connect the LAN A data terminal of any
LAN device (eg. Keypads, expansion
14 LAN A boards) to this terminal. The control
panel supports up to 300 m of 24/0.20
(18 AWG) wire on these terminals.
Connect the LAN B data terminal of any
LAN device (eg. Keypads, expansion
15 LAN B boards) to this terminal. The control
panel supports up to 300 m of 24/0.20
(18 AWG) wire on these terminals.
Alarm power capable of providing a
16 COMM+ maximum of 2 Amp (+). This terminal is
PTC Fuse protected.
17 OUT 1 Programmable
18 OUT 2 providing a maximum of 500 mA (-). This
19 OUT 3 terminal is PTC Fuse protected.
20 N/C
2 A @ 24 VDC Relay Output -
21 COM
Form C contact
22 N/O
Programmable Input for RF Receivers,
23 INPUT
Keyswitch and other devices.
24 ZN 1 Zone 1 and 9 sensor loop input (+).
Common (-) for Zone 1 and 2 sensor
25 GND
loop.
26 ZN 2 Zone 2 and 10 sensor loop input (+).
27 ZN 3 Zone 3 and 11 sensor loop input (+).
Common (-) for Zone 3 and 4 sensor
28 GND
loop.
29 ZN 4 Zone 4 and 12 sensor loop input (+).
30 ZN 5 Zone 5 and 13 sensor loop input (+).
Common (-) for Zone 5 and 6 sensor
31 GND
loop.
Bosch Security Systems 09/06 BLCC100R
Description
output, capable
Nº Name
32 ZN 6 Zone 6 and 14 sensor loop input (+).
33 ZN 7 Zone 7 and 15 sensor loop input (+).
Common (-) for Zone 7 and 8 sensor
34 GND
loop.
35 ZN 8 Zone 8 and 16 sensor loop input (+).
36 IN These terminals are used to connect the
37 IN telephone line from the street.
38 OUT These terminals are used to connect the
39 OUT premises telephones.

Table 4: Terminal Block Descriptions

B oa rd Co nnec tor s
Connector
This socket allow you to connect a service
Service
Keypad to the panel during installation.
This socket is used to connect the panel
Tamper
enclosure tamper switch.
This push button is used to reset the con-
Default
trol panel back to factory default.
Voice This is used to connect the optional Voice
Module Command Module (CM100).
This socket is used to connect serial devic-
Serial es to the control system like the direct link
programming module.
This is a RJ12 6P/4C connector that allows
Telco you to connect the control panel to the
PSTN telephone line.
of
The relay select PIN's allow you to eas-
ily program the relay common contact to
Relay
switch either +12v or GND by fitting a plug
on link.

Table 5: Board Connector Descriptions

Abou t The Key pa d
The Graphic Keypad has 20 keys or buttons. The buttons
allow you to input instructions and navigate the menu
screens as required. Some buttons have a secondary
function which is activated by holding them down for two
seconds. Each button's function is described below
Key pa d Key Fu nc tions
Key
to
Solution 16 Quick Start Guide
plus
Description
Description
Description
The numeric keys allow you to enter
you numbers when required
Use the [MENU] and the numeric keys
to enter commands. The [MENU] key
is also used to go back one level when
navigating through menus or to exit a
programming location without saving
changes.
9