Defaulting The System; Domestic Template Defaults; Direct Link Programming; Zone Array - Bosch Solution 16plus Quick Start Manual

Solution 16 Quick Start Guide
plus
To Hardware Default
1) Remove All Power To The System. AC and
Battery.
2) Press and Hold The Default Push Button
Down Then Apply Power To The System.
3) Release Button, The Panel Will Reset And
Revert To Normal Operation When Default Is
Complete.
To Software Default
1) Enter Program Mode.
[1234 +MENU]
2) Select Factory Default Option.
[MENU 7-0-4)
3) The Panel Will Reset And Revert To Normal
Operation When Default Is Complete.
You can disable factory defaulting using MENU 7-7-
i
4. If factory defaulting has been disabled you must
Note
know the installer code to perform a factory default
otherwise the system will need to be returned to
your supplier for defaulting or you can purchase a
CM255 Default Unlock Key which will unlock the
panel in the field. Charges apply for defaulting if
retuned to the distributor.
D om e s t ic Tem p late D efau lts
The following table list the changes that will occur when
you select domestic default.
Program Option
All Trouble Reports
All Bypass Reports
All Restore Reports
Destination 1 TX Format
Open / Close Reports
System Events Route

Table 10: Domestic Keypad DIP Switch Address Settings

D ire c t Link Programm i n g
The panel can be programmed via the Solution Link
Upload/Download software in either Direct Link or Remote
Link modes. For Direct Link you will need a CM900 Direct
Link module which connected the panels serial port to the
PC.
Once the cable is connected you will need to hold down
the default switch on the panel for 5 seconds to initiate the
programming session. See Figure 12: for the default switch
location. It is also possible to initiate the programming
session via [MENU 5-0-5] Start Direct Link.
14
Domestic Default Value
Disabled
Disabled
Disabled
Domestic Reporting
Disabled (all areas)
Log Only
Zo ne Array
The feature allows you to view the condition of 16 zones
at a time on a single display. From the installer programing
mode press [Menu] 3-0-1 to access the zone array.
Use Keys [] and [] to scroll up and down the zone bank
Press [OK] or [MENU] when finished.
N= NORMAL
S = SHORTED
A= ALARM
T= TAMPER
- = DISABLED
0000000001111111
1234567890123456
NSA-ANAT--------

PRESS , OK or MENU

Figure 20: Sample Zone Array Display

In the above example screen,
N = Zone 01 and 06 are Normal (Sealed)
S = Zone 02 is Shorted
A = Zone 03,05,07 are in Alarm (Unsealed)
T = Zone 08 is in Tamper Alarm (Unsealed)
- = Zone 04, 09-16 are Disabled (Unused)
B a s ic R epor ting R efe ren ce
A complete reporting template is available on the Solution
Link CD or from your nearest Bosch security products
outlet. Your base station will need to create a specific
reporting template for this and other new model Solution
panels.
Point ID Table
Ur999
Ur998
Ur001 - 256
Ur000
Zn301-428
Zn891-898
Zn881-888
Zn871-878
Zn861-868
Zn851-858
Zn841-848
Zn831-838
Zn821-828
Zn811-818
Zn801-808
Zn781-788
Zn791-798
Zn001-128

Table 11: Basic Reporting Code Reference Listing

Module Description
Installer
Remote User
Users
Quick Arm
User Keyfob 1 - 128
Panels 1-8
Keypads 1-8
Ethernet 1-8
GSM 1-8
Output Expander 1-8
Serial Expander 1-8
Lan P/Supply 1-8
RF Reciever 1-8
Access 1-8
X10 1-8
Input Expander
Lift 1-8
Zones
Bosch Security Systems 09/06 BLCC100R