Device Programming - Bosch Solution 16plus Quick Start Manual

Solution 16 Quick Start Guide
plus
Comms > Dialler Reporting >
Burg Report Delay
Enter 0 – 255 seconds + [OK] To Program The Delay Time In Seconds
Before Reports Are Sent. 0 = No Delay
Comms > Dialler Reporting >
Fire Report Delay
Enter 0 – 255 seconds + [OK] To Program The Delay Time In Seconds
Before Reports Are Sent. 0 = No Delay
Comms > Comms Test >
Send Test Report
Comms > Comms Test >
Test Report Time
Use the [] and [] keys to move to the field then [] and [] to
change. Press [OK] to save or [MENU] to exit without saving.
Scroll through hours using the
i
from am to pm.
Note
Comms > Comms Test >
Test Report Period
0 = No Test Report
1 = Every Day
2 = Every Week
3 = Every Month
MENU 5-9-3 Programs The Interval Between Automatic Test Reports.
Use Keys [] and [] keys or enter [0] to [3] + [OK] To Program.
(*** System Wide Parameter ***)
Comms > Comms Test >
Test Report Options
1 Send Test Reports Only If No Other Report
2 Send Test Reports On Siren Reset / Time Out
3
Reserved
4
Reserved
5 Reserved
6 Reserved
7 Reserved
8
Reserved
Use Keys [] and [] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [] will display
to indicate option set. Press [OK] To Save when finished.
28
MENU 5-4-6
0 0
SECONDS
(*** System Wide Parameter ***)
MENU 5-4-7
0 0
SECONDS
(*** System Wide Parameter ***)
MENU 5-9-0
MENU 5-9-1
Test Time
02 : 00 am
HH MM
and to change
[] []
MENU 5-9-2
MENU 5-9-3
Comms > Comms Test >
Test Route
0 = Report Events To Log Only
0
1 = Report Events To Destination 1 + Log
2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
4 = Report Events To Destination 2 If Destination 1 Fails + Log
Use Keys [] and [] keys or enter 0 - 4 + [OK]. To Enter Single Option
Only.
(*** System Wide Parameter ***)
0
Comms > Comms Test >
Dial Number Test
Use the option to test the system dialer to your mobile or other phone.
Enter the digits to dial and press OK. The system will call the number
entered. This function will stop after 30 seconds or by pressing OK.
Enter [0] – [9] For Telephone Digits.
Use [] and [] To Toggle Special Characters  # and , (Pause)
Dev ice Progra m ming
Devices > Commands >
LAN Status
LAN Secure
Devices > Keypads >
Keypad Volume
Keypad Contrast
Keypad Backlight
Devices > Keypads >
Home Area
1
Use Keys [] and [] keys or enter 1 - 4 Then Press [OK] To Set The
Home Area. This is the Area which will be diplayed on the keypad by
default.
All keypads must have a home area programmed
i
to work correctly.
Note
Devices > Keypads >
General Options
N
1 Keypad Extinguish
Y
2 Greeting On Arming
N 3
Greeting On Disarming
N 4
Enable Rear Tamper
N
5 PIN To Change Area
N
6 Home Area Only
N
7
Report/Display Keypad Temperature
N 8
Display Area ICON Indicators
Use Keys [] and [] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [] will display
to indicate option set. Press [OK] To Save when finished.
MENU 5-9-4
1
MENU 5-9-5
MENU 6-0-0
MENU 6-0-1
MENU 6-1-0
MENU 6-1-1
MENU 6-1-2
MENU 6-1-3
1
MENU 6-1-4
N
Y
Y
N
N
N
Y
N
Bosch Security Systems 09/06 BLCC100R