Bosch Solution 16plus Quick Start Manual page 27

Comms > Remote Access >
DTMF Options
1
DTMF Arming
2
DTMF Disarming
3 DTMF User Functions
4 DTMF Quick Arm ([0] + [#])
5
Reserved
6
Reserved
7 Reserved
8 Reserved
Use Keys [] and [] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [] will display
to indicate option set. Press [OK] To Save when finished.
Comms > Remote Access >
Voice Access Code
If a Voice Module is used enter the 2-digit access code used to access the
system. Use [] and [] Keys To Scroll Cursor Left and Right. Enter [0]
– [9] For Digits and Use [] and [] To Toggle Special Characters.
Comms > Remiote Access >
CLI Number
1
First
Number
1
Second
Number
1
Third
Number
Use [] and [] Keys To Scroll Cursor. Enter [0] – [9] For Telephone
Digits. Use [] and [] To Toggle Special Characters  # and , (Pause)
Up to 3 Phone numbers can be entered for CLI Call
i
Line Identification for remote access detection.
Note
You must enter STD code plus the compete number
for this option to work. Press [OK] after each
telephone number is entered to save and move to
the next number.
Comms > Dialler Reporting >
TX Format Dest 1
0 = Disable
1 = Contact ID 7 = Domestic
2 = SIA 8 = Voice
3 = Serial STU 9 = SIA +
4 = GSM 10 = Reserved
5 = WEB MAIL 11 = Reserved
6 = SMS 12 = Reserved
Use Keys [] and [] keys or enter 0 – 15 Then Press [OK] To Program
The Transmission Format The Control Panel Will Use To Report To
Destination 1. Only 1 Option Can Be Programmed.
Bosch Security Systems 09/06 BLCC100R
MENU 5-3-5
MENU 5-3-6
9
MENU 5-3-7
Digits
Digits
Digits
MENU 5-4-0
13 = Reserved
14 = Reserved
15 = Reserved
Comms > Dialler Reporting >
TX Format Dest 2
Y
0 = Disable
N
1 = Contact ID
N 2 = SIA
3 = Serial STU
Y
4 = GSM
N
5 = WEB MAIL
N
6 = SMS
N
Use Keys [] and [] keys or enter 0 – 15 Then Press [OK] To Program
N
The Transmission Format The Control Panel Will Use To Report To
Destination 2. Only 1 Option Can Be Programmed.
Comms > Dialler Reporting
Test Route
0 = Report Events To Log Only
#
1 = Report Events To Destination 1 + Log
2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
4 = Report Events To Destination 2 If Destination 1 Fails + Log
Use Keys [] and [] keys or enter 0 - 4 + [OK]. To Enter Single Option
Only.
(*** System Wide Parameter ***)
32
Comms > Dialler Reporting
Status Route
32
0 = Report Events To Log Only
1 = Report Events To Destination 1 + Log
32 2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
4 = Report Events To Destination 2 If Destination 1 Fails + Log
MENU 5-5-4 Routes System Status Reports. Use Keys [] and [] keys
or enter 0 - 4 + [OK]. To Enter Single Option Only.
(*** System Wide Parameter ***)
Comms > Dialler Reporting
Emergency Route
0 = Report Events To Log Only
1 = Report Events To Destination 1 + Log
2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
1
4 = Report Events To Destination 2 If Destination 1 Fails + Log
Use Keys [] and [] keys or enter 0 - 4 + [OK]. To Enter Single Option
Only.
(*** System Wide Parameter ***)
Comms > Dialler Reporting >
Swinger Dialler
Enter 0 – 15 + [OK] To Program Number Of Times The Dialler Can
Report Before Lockout.
0 = Unlimited
Solution 16 Quick Start Guide
plus
7 = Domestic
8 = Voice 13 = Reserved
9 = SIA + 14 = Reserved
10 = Reserved 15 = Reserved
11 = Reserved
12 = Reserved
(*** System Wide Parameter ***)
MENU 5-4-1
1
MENU 5-4-2
1
MENU 5-4-3
1
MENU 5-4-4
1
MENU 5-4-5
0 6
27