Korg pa 900 User Manual: Filter: Filter Eg

Professional arranger.
Hide thumbs
   
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450

Advertisement

Sound mode
220

Filter: Filter EG

Intensity to A
Specifies the depth and direction of the effect that "AMS" will
have on filter A.
For example if "AMS" is Joystick Y+, higher settings of this
parameter will allow greater change to be applied to LFO1 when
you move the Joystick up in the Y axis.
-99...+99
Parameter value.
Intensity to B
Specifies the depth and direction of the effect that "AMS" will
have on filter B (see "Intensity to A").
LFO 2
Adjusts the depth of the cyclic modulation applied by LFO2 (set
on "LFO: LFO2") to the cutoff frequency of filters A and B. For
more information on the parameters see "LFO 1" above.
Filter: Filter EG
Here you can make settings for the EG that will produce time-
varying changes in the cutoff frequency of filters A and B for the
selected oscillator. The depth of the effect that these settings will
have on the filter cutoff frequency is determined by the "Veloc-
ity" and "Intensity" parameters.
Diagram
The diagram on top of the page shows the Filter envelope line.
Filter envelope
Attack Level
Note-on
The specified
cutoff
frequency
Start
Attack
Decay
Level
Time
Time
Level
These are the envelope segment levels. The result will depend on
the filter that was selected in "Filter Type". For example, with the
Low Pass Resonance filter, positive (+) values of EG Intensity
will cause the tone to be brightened by positive (+) levels, and
darkened by negative (–) levels.
Note-off
Sustain Level
Release
Level
Break
Point
Time
Level
Slope
Release
Time
Time
Start
This parameter specifies the change in cutoff frequency at the
time of note-on.
-99...+99
Level value.
Attack
This parameter specifies the change in cutoff frequency after the
attack time has elapsed.
-99...+99
Level value.
Break (Break Point)
This parameter specifies the change in cutoff frequency after the
decay time has elapsed.
-99...+99
Level value.
Sustain
This parameter specifies the change in cutoff frequency that will
be maintained from after the slope time has elapsed until note-
off occurs.
-99...+99
Level value.
Release
This parameter specifies the change in cutoff frequency that will
occur when the release time has elapsed.
-99...+99
Level value.
Time
These parameters specify the time over which the filter change
will occur.
Attack
This parameter specifies the time over which the level will
change from note-on until the attack level is reached.
0...99
Time value.
Decay
This parameter specifies the time over which the level will
change from the attack level to the break point level.
0...99
Time value.
Slope
This parameter specifies the time over which the level will
change after the decay time has elapsed until the sustain level is
reached.
0...99
Time value.
Release
This parameter specifies the time over which the level will
change after note-on occurs until the release level is reached.
0...99
Time value.

Advertisement

   Also See for Korg pa 900

   Related Manuals for Korg pa 900

Comments to this Manuals

Symbols: 0
Latest comments:
  • Vikas kumar Mar 30, 2017 03:31:
    By mistake I delete my synth fx get back please tell me, I'm worried about my korg pa 900 , how can I get my effects.
  • Jorge Leiva Sep 10, 2016 01:25:
    Port favor, me pueden ayudar a traducir este manual (el de 450 páginas?
    Gracias.